Fluke Corporation
Everett, WA 98203
Share:
New Valve Tester from Fluke Reduces Test Time
Fluke’s new Loop Valve Tester is a handheld device that simplifies testing by performing a quick health check. The device allows for testing without removal of the valve, simplifying the process. Technicians can source the 4-20 mA signal while the device is interrogating HART data, collecting critical information about the valve’s position and status. With its built-in tests and interface,...
Read More »
New Fluke 3561 FC Vibration Sensor Allows Wireless Transmission via Fluke 3502 FC Gateway
The Fluke 3561 FC Vibration Sensor detects and notifies the user with conditional changes caused due to imbalance, misalignment, looseness and bearing wear. The unit provides a frequency range of 10 to 1,000 Hz and enables maintenance teams to improve uptime by adding continuous vibration monitoring of any rotating equipment. The Fluke Connect™ Condition Monitoring software allows teams to...
Read More »
Fluke 729 Automatic Pressure Calibrator is Finalist in Control Engineering's Engineers' Choice Awards
New pressure calibrator recognized for improving repeatability and simplifying the calibration process EVERETT, Wash., Oct. 31, 2017 - The Fluke® 729 Automatic Pressure Calibrator is a finalist in the Hardware - Handheld Test, Measurement, Calibration category of the Control Engineering 2018 Engineers' Choice Awards. The awards honor the best control, instrumentation, and automation products as...
Read More »
Fluke T6 Electrical Testers come with backlight reading display.
Fluke® T6 Electrical Testers are offered in T6-600 and T6-1000 models. Units are used to measure true-rms in crowded junction boxes or conductors and come with open fork. Products are 1000 V CAT III, 600 V CAT IV safety rated and use Fluke FieldSense technology. Testers offer voltage and current readings. T6 can measure voltage up to 1000V and 4/0 wires up with current up to 200 A.
Read More »
DATAPAQ® EasyTrack®3 Data Logger features polycarbonate casing.
Capable of storing 18,000 readings per channel, DATAPAQ® EasyTrack®3 Data Logger uses 9 V replaceable batteries which provide more than 50 profiling runs. Featuring traffic light indicator, product is embedded with Insight™ Professional software for analyzing rise/fall, peak difference, area under curve calculation.
Read More »
5128A RHapid-Cal Humidity Generator provides six-point calibration in two hours.
Used for calibrating probes and loggers in the field or in laboratory, 5128A RHapid-Cal Humidity Generator is suitable for pharmaceuticals, medical devices, semiconductors, chemicals, and food production industries. Offering ± 1.0% RH system accuracy for dependable humidity probe calibration, unit provides rapid humidity and temperature stabilization time 10ºC/minute and 1.5ºC/minute for...
Read More »
Fluke 1630-2 FC Stakeless Earth Ground Clamp performs automatic data recording.
Capable of storing 32,760 measurements in memory, Fluke 1630-2 FC Stakeless Earth Ground Clamp automatically records data at pre-set intervals. Product is integrated with Fluke Connect® which helps in viewing, recording and sharing measurements through smartphones or tablets. Unit helps electrician for measuring earth ground loop resistance using dual-clamp jaw.
Read More »
DATAPAQ MonoPaq2 System offers accuracy of
Measuring merely 41 x 48 x 195 mm, DATAPAQ MonoPaq2 system profiles metal temperature of coated aluminum bottles, aerosols, and collapsible tubes both in IBO and OBO lines. Featuring DATAPAQ Insight software, system allows reviewing of versatile visualization, analysis and reporting functions. Logging up to 32,000 readings per channel with adjustable interval of 0.05 s or more, unit’s Q18...
Read More »DATAPAQ SelectivePaq System offers wave contact times data analysis.
Combining four-channel Q18 micro data logger with latest micro-miniature thermocouple plugs and low-mass thermal shield of 20 mm high and 40 mm wide, DATAPAQ SelectivePaq thermal profiling system features data logger of ±0.5 °C accuracy and 0.1°C resolution. Including aluminum logger case and rechargeable battery, unit offers soldering process sensor array. With Insight Reflow software, device...
Read More »
Plant Engineering Recognizes the Fluke Connect Reliability Platform for Improving Workforce Efficiency and Productivity
Fluke Condition Monitoring and 279 FC Thermal Multimeter, both part of the Fluke Connect system, are finalists in the magazine's awards EVERETT, Wash., Dec. 1, 2016 - Fluke® Condition Monitoring and the Fluke® 279 FC Thermal Multimeter are finalists in the Maintenance Tools and Equipment category of the Plant Engineering 2016 Product of the Year Awards. The awards honor new products that help...
Read More »
New Valve Tester from Fluke Reduces Test Time
Fluke’s new Loop Valve Tester is a handheld device that simplifies testing by performing a quick health check. The device allows for testing without removal of the valve, simplifying the process. Technicians can source the 4-20 mA signal while the device is interrogating HART data, collecting critical information about the valve’s position and status. With its built-in tests and interface,...
Read More »
New Fluke 3561 FC Vibration Sensor Allows Wireless Transmission via Fluke 3502 FC Gateway
The Fluke 3561 FC Vibration Sensor detects and notifies the user with conditional changes caused due to imbalance, misalignment, looseness and bearing wear. The unit provides a frequency range of 10 to 1,000 Hz and enables maintenance teams to improve uptime by adding continuous vibration monitoring of any rotating equipment. The Fluke Connect™ Condition Monitoring software allows teams to...
Read More »
Fluke 729 Automatic Pressure Calibrator is Finalist in Control Engineering's Engineers' Choice Awards
New pressure calibrator recognized for improving repeatability and simplifying the calibration process EVERETT, Wash., Oct. 31, 2017 - The Fluke® 729 Automatic Pressure Calibrator is a finalist in the Hardware - Handheld Test, Measurement, Calibration category of the Control Engineering 2018 Engineers' Choice Awards. The awards honor the best control, instrumentation, and automation products as...
Read More »
Fluke T6 Electrical Testers come with backlight reading display.
Fluke® T6 Electrical Testers are offered in T6-600 and T6-1000 models. Units are used to measure true-rms in crowded junction boxes or conductors and come with open fork. Products are 1000 V CAT III, 600 V CAT IV safety rated and use Fluke FieldSense technology. Testers offer voltage and current readings. T6 can measure voltage up to 1000V and 4/0 wires up with current up to 200 A.
Read More »
DATAPAQ® EasyTrack®3 Data Logger features polycarbonate casing.
Capable of storing 18,000 readings per channel, DATAPAQ® EasyTrack®3 Data Logger uses 9 V replaceable batteries which provide more than 50 profiling runs. Featuring traffic light indicator, product is embedded with Insight™ Professional software for analyzing rise/fall, peak difference, area under curve calculation.
Read More »
5128A RHapid-Cal Humidity Generator provides six-point calibration in two hours.
Used for calibrating probes and loggers in the field or in laboratory, 5128A RHapid-Cal Humidity Generator is suitable for pharmaceuticals, medical devices, semiconductors, chemicals, and food production industries. Offering ± 1.0% RH system accuracy for dependable humidity probe calibration, unit provides rapid humidity and temperature stabilization time 10ºC/minute and 1.5ºC/minute for...
Read More »
Fluke 1630-2 FC Stakeless Earth Ground Clamp performs automatic data recording.
Capable of storing 32,760 measurements in memory, Fluke 1630-2 FC Stakeless Earth Ground Clamp automatically records data at pre-set intervals. Product is integrated with Fluke Connect® which helps in viewing, recording and sharing measurements through smartphones or tablets. Unit helps electrician for measuring earth ground loop resistance using dual-clamp jaw.
Read More »
DATAPAQ MonoPaq2 System offers accuracy of
Measuring merely 41 x 48 x 195 mm, DATAPAQ MonoPaq2 system profiles metal temperature of coated aluminum bottles, aerosols, and collapsible tubes both in IBO and OBO lines. Featuring DATAPAQ Insight software, system allows reviewing of versatile visualization, analysis and reporting functions. Logging up to 32,000 readings per channel with adjustable interval of 0.05 s or more, unit’s Q18...
Read More »DATAPAQ SelectivePaq System offers wave contact times data analysis.
Combining four-channel Q18 micro data logger with latest micro-miniature thermocouple plugs and low-mass thermal shield of 20 mm high and 40 mm wide, DATAPAQ SelectivePaq thermal profiling system features data logger of ±0.5 °C accuracy and 0.1°C resolution. Including aluminum logger case and rechargeable battery, unit offers soldering process sensor array. With Insight Reflow software, device...
Read More »
Plant Engineering Recognizes the Fluke Connect Reliability Platform for Improving Workforce Efficiency and Productivity
Fluke Condition Monitoring and 279 FC Thermal Multimeter, both part of the Fluke Connect system, are finalists in the magazine's awards EVERETT, Wash., Dec. 1, 2016 - Fluke® Condition Monitoring and the Fluke® 279 FC Thermal Multimeter are finalists in the Maintenance Tools and Equipment category of the Plant Engineering 2016 Product of the Year Awards. The awards honor new products that help...
Read More »