Pulse Instruments
Torrance, CA 90502-1200
Share:
VCO Clock Source provides 100 ppm resolution.
Manually programmable, self-contained Model PRL-174ANT-1350 generates TTL and ECL clock signals from 1.2 MHz to 1.35 GHz. Clock frequency is continuously adjustable from 600 MHz to 1.35 GHz from front panel. In fine adjust mode, full operating range is divided via 16-position rotary switch. In coarse adjust mode, 10-turn pot controls entire 600 MHz to 1.35 GHz range. Typical stability is 100 ppm...
Read More »Receiver and Line Driver suit long-distance applications.
Universal Differential Receivers and Line Drivers in PRL 425 Series are compact, self-contained buffer pods that can receive any differential signal with min amplitude of 100 mV and CMR between -2.4 and +4 V. Long line drivers have differential TTL and RS-422 outputs that can run up to 300 MHz and NECL outputs up to 1.8 GHz. PRL-425 Universal Differential Receiver suits line-driver applications...
Read More »TTL/NECL Frequency Divider has programmable, 2-phase design.
Self-contained divider pod, PRL-260ANT, accepts input frequency f from dc to 1 GHz and outputs divided TTL and ECL clock signals with ratios from f/2-f/4096. Able to be cascaded with additional PRL frequency dividers, it accepts TTL and ECL clock signals as well as ac-coupled PECL, LVPECL, or sinewave signals. All divided outputs are synchronous with input frequency, and division ratios are...
Read More »
Frequency Divider accepts TTL clock signals from DC-100 MHz.
Self-contained, 4 Decade TTL Model PRL 230 generates f/10, f/100, f/1,000, and f/10,000 divided outputs. TTL input has switchable 50 ohm/500 ohm input impedance, and can toggle up to 100 MHz. Four divided TTL outputs are back-matched, and each delivers greater than 2.2 V into 50 ohm load. Outputs are synchronous with input frequency and can be used for triggering data acquisition systems, pattern...
Read More »
Switch/Signal Router features 1x4, 1.75 GHz configuration.
Measuring 1.3 x 2.9 x 2.9 in., self-contained PRL-854 switches one 50 ohm input to any of four 50 ohm outputs under manual or remote control. It has 3 dB bandwidth of 1.75 GHz typ and works for microwave and high-speed digital signals from dc to 2.5 GHz. Unit can also be used as reflective scanner, switching 4 inputs to one output. Manual models have rotary switch for channel selection, and...
Read More »
Line Driver drives 4 TTL/CMOS signals into 50 ohm loads.
With 10 kohm input impedance, self-contained Model PRL-444 can receive signals from devices with low drive current such as sensors, PC-based digital I/O cards, and optical transceivers. Each input has 10 kohm pulled up to 2.5 V so it can also be driven by open-collector devices. With 50 ohm terminations, all outputs can drive 100 ft of 50 ohm cables at clock rates greater than 60 MHz. Driver...
Read More »
Quad-Channel Line Driver is suited for laboratory use.
Featuring 10 kohm input impedance, PRL 444 self-contained buffer pod drives 4 TTL/CMOS signals into 50 ohm loads and can receive signals from devices with low drive current. Unit comes in aluminum housing with ac adapter and BNC or SMA signal connectors. With 50 ohm load terminations, all outputs can drive 100 ft of 50 ohm cables at clock rates exceeding 60 MHz. Applications include digital...
Read More »
Data Acquisition Card is suited for image capture.
Model PI-41000 offers twin, software configurable, 100 MHz inputs that can acquire digital data at rates up to 400 MBps. CompactPCIÃ-® instrument card has on-board memory of 128-512 MB. With optional 4:1 multiplexer cards, one PI-41000 can acquire up to 8 digital channels. Suited for synchronous data capture and testing imaging devices, unit offers continuous acquisition at full frame rate...
Read More »
Data Acquisition System offers multi-channel capabilities.
Model PI-3105 tests analog imaging devices with multiple outputs. It offers programmable gain, filter, strobe timing, and CDS timing on per channel basis, and provides global offset control. All analog components are electronically isolated from digital section ensuring low noise environment. Scalable system offers 1-32 channels of signal conditioning and A/D conversion. Digital data are...
Read More »Line Driver sends up to 4 identical signals over long lines.
Self-contained Model PRL-414B is a 1:4 TTL fanout line driver that delivers precision clock and logic signals from DC to 100 MHz to multiple loads over long lines. With 50 ohm line drivers, outputs of PRL-414B can drive up to 100 ft of 50 ohm cables at clock rates greater than 80 MHz. Typical output rise and fall times are 2 ns. Applications include data acquisition monitoring and synchronous...
Read More »VCO Clock Source provides 100 ppm resolution.
Manually programmable, self-contained Model PRL-174ANT-1350 generates TTL and ECL clock signals from 1.2 MHz to 1.35 GHz. Clock frequency is continuously adjustable from 600 MHz to 1.35 GHz from front panel. In fine adjust mode, full operating range is divided via 16-position rotary switch. In coarse adjust mode, 10-turn pot controls entire 600 MHz to 1.35 GHz range. Typical stability is 100 ppm...
Read More »Receiver and Line Driver suit long-distance applications.
Universal Differential Receivers and Line Drivers in PRL 425 Series are compact, self-contained buffer pods that can receive any differential signal with min amplitude of 100 mV and CMR between -2.4 and +4 V. Long line drivers have differential TTL and RS-422 outputs that can run up to 300 MHz and NECL outputs up to 1.8 GHz. PRL-425 Universal Differential Receiver suits line-driver applications...
Read More »TTL/NECL Frequency Divider has programmable, 2-phase design.
Self-contained divider pod, PRL-260ANT, accepts input frequency f from dc to 1 GHz and outputs divided TTL and ECL clock signals with ratios from f/2-f/4096. Able to be cascaded with additional PRL frequency dividers, it accepts TTL and ECL clock signals as well as ac-coupled PECL, LVPECL, or sinewave signals. All divided outputs are synchronous with input frequency, and division ratios are...
Read More »
Frequency Divider accepts TTL clock signals from DC-100 MHz.
Self-contained, 4 Decade TTL Model PRL 230 generates f/10, f/100, f/1,000, and f/10,000 divided outputs. TTL input has switchable 50 ohm/500 ohm input impedance, and can toggle up to 100 MHz. Four divided TTL outputs are back-matched, and each delivers greater than 2.2 V into 50 ohm load. Outputs are synchronous with input frequency and can be used for triggering data acquisition systems, pattern...
Read More »
Switch/Signal Router features 1x4, 1.75 GHz configuration.
Measuring 1.3 x 2.9 x 2.9 in., self-contained PRL-854 switches one 50 ohm input to any of four 50 ohm outputs under manual or remote control. It has 3 dB bandwidth of 1.75 GHz typ and works for microwave and high-speed digital signals from dc to 2.5 GHz. Unit can also be used as reflective scanner, switching 4 inputs to one output. Manual models have rotary switch for channel selection, and...
Read More »
Line Driver drives 4 TTL/CMOS signals into 50 ohm loads.
With 10 kohm input impedance, self-contained Model PRL-444 can receive signals from devices with low drive current such as sensors, PC-based digital I/O cards, and optical transceivers. Each input has 10 kohm pulled up to 2.5 V so it can also be driven by open-collector devices. With 50 ohm terminations, all outputs can drive 100 ft of 50 ohm cables at clock rates greater than 60 MHz. Driver...
Read More »
Quad-Channel Line Driver is suited for laboratory use.
Featuring 10 kohm input impedance, PRL 444 self-contained buffer pod drives 4 TTL/CMOS signals into 50 ohm loads and can receive signals from devices with low drive current. Unit comes in aluminum housing with ac adapter and BNC or SMA signal connectors. With 50 ohm load terminations, all outputs can drive 100 ft of 50 ohm cables at clock rates exceeding 60 MHz. Applications include digital...
Read More »
Data Acquisition Card is suited for image capture.
Model PI-41000 offers twin, software configurable, 100 MHz inputs that can acquire digital data at rates up to 400 MBps. CompactPCIÃ-® instrument card has on-board memory of 128-512 MB. With optional 4:1 multiplexer cards, one PI-41000 can acquire up to 8 digital channels. Suited for synchronous data capture and testing imaging devices, unit offers continuous acquisition at full frame rate...
Read More »
Data Acquisition System offers multi-channel capabilities.
Model PI-3105 tests analog imaging devices with multiple outputs. It offers programmable gain, filter, strobe timing, and CDS timing on per channel basis, and provides global offset control. All analog components are electronically isolated from digital section ensuring low noise environment. Scalable system offers 1-32 channels of signal conditioning and A/D conversion. Digital data are...
Read More »Line Driver sends up to 4 identical signals over long lines.
Self-contained Model PRL-414B is a 1:4 TTL fanout line driver that delivers precision clock and logic signals from DC to 100 MHz to multiple loads over long lines. With 50 ohm line drivers, outputs of PRL-414B can drive up to 100 ft of 50 ohm cables at clock rates greater than 80 MHz. Typical output rise and fall times are 2 ns. Applications include data acquisition monitoring and synchronous...
Read More »