Master Bond, Inc.

Clear Compound laminates, seals, bonds, and coats.
Adhesives & Sealants

Clear Compound laminates, seals, bonds, and coats.

Single-component UV19LV bonds and seals clear films and sheets to other films, paper, and foil substrates. Uninhibited by air, 100% reactive, acrylic-based polymer composition does not emit any VOCs during cure. Mobile liquid has viscosity under 300 cps @ 75°F and cures in 10-15 sec using UV cure equipment in 365 nm range. With operating temperature range of -60 to +250°F, cured...

Read More »
UV Curable Compound adheres to plastic, glass, and metals.
Adhesives & Sealants

UV Curable Compound adheres to plastic, glass, and metals.

Flexible, optically clear UV19 cures upon exposure to UV light at ambient temperatures. Compound is 100% reactive, does not contain any volatiles, and offers abrasion resistance and heat stability. With tensile strength in excess of 800 psi and viscosity of less than 300 cps at 75°F, compound is suited for laminating, sealing, and bonding to substrates with different thermal expansion...

Read More »
Epoxy Adhesive offers electrically insulating properties.
Adhesives & Sealants

Epoxy Adhesive offers electrically insulating properties.

Thermally conductive, 2-part EP21TDCAOHT bonds dissimilar substrates with different coefficients of expansion and contraction. Adhering to metals, ceramics, glass, rubbers, and plastics, product has 1:1 mix ratio by weight or volume and cures at room temperature or more rapidly at elevated temperatures. Exhibiting thermal and mechanical shock resistance, it has paste viscosity, 35 pli T-peel...

Read More »

Optically Clear Epoxy cures at room temperature.

Suited for bonding, coating, sealing, and casting, EP30LV bonds to similar and dissimilar substrates. Once hardened, product provides electrical insulation with service operating temperature of -60 to +250°F. Formulation is 100% reactive and does not contain solvents or other volatiles. Bonds are rigid and resistant to water, oil, and most organic solvents. Epoxy offers tensile strength of...

Read More »
Flexible Adhesive/Sealant meets USP Class VI requirements.
Adhesives & Sealants

Flexible Adhesive/Sealant meets USP Class VI requirements.

Optically clear, UV-curable UV15X-6 polymer system adheres to various substrates, including plastics and elastomers. Suited for medical device assemblies, single-component urethane formulation is 100% reactive, does not contain any volatiles, and also acts as electrical insulator. Cure is not affected by air or moisture, and cured material exhibits abrasion resistance. Bonds resist exposure to...

Read More »
Epoxy Potting Compound provides electrical insulation.
Adhesives & Sealants

Epoxy Potting Compound provides electrical insulation.

Two-component EP121AO-1 offers thermal conductivity as well as thermal and dimensional stability. It features chemical resistance even when exposed to adverse environmental conditions. Service operating temperature is 475-500°F for limited time periods and 400-450°F for prolonged exposures. Medium-viscosity liquid adheres to metallic and non-metallic surfaces. It has 100:80 mix ratio...

Read More »
Silver Conductive Epoxy Adhesive sets up in 5-10 minutes.
Adhesives & Sealants

Silver Conductive Epoxy Adhesive sets up in 5-10 minutes.

Suited for similar and dissimilar substrates, EP77M-F forms bonds that are resistant to thermal cycling and chemicals. Full cure takes 8-12 hr at room temperature, and electrical conductivity is first detectable within 30-60 min. With low volume resistivity of 10-3 ohm-cm, 2-component, silver-filled, 100% reactive epoxy adhesive has 4°K to 125°C service operating temperature and 1:1...

Read More »
Adhesive/Sealant bonds dissimilar substrates.
Adhesives & Sealants

Adhesive/Sealant bonds dissimilar substrates.

Cured at room or elevated temperatures, 2-component EP21TDCHT-1 has temperature range serviceability of -100 to +400°F. Compound serves as electrical insulator with volume resistivity of 1014 ohm-cm. Epoxy adhesive/sealant is resistant to vibration, impact, and thermal shock as well as exposure to water, oils, and organic solvents. It has 70 Shore D hardness, 3,000+ psi tensile strength,...

Read More »
Epoxy Adhesive/Sealant/Coating is chemical-resistant.
Adhesives & Sealants

Epoxy Adhesive/Sealant/Coating is chemical-resistant.

Featuring thermal stability, 2-component EP21ARHT-1 is 100% reactive and does not contain any solvents or diluents. It has 2:1 mix ratio by weight and cures at room temperature. Exhibiting minimal shrinkage upon cure, product does not sag or drip on vertical surfaces. Designed to withstand thermal shock and abrasion, it adheres to metals, glass, ceramics, cements, woods, vulcanized rubbers, and...

Read More »
UV Curable Epoxy Resin exhibits 2-3% shrinkage upon cure.
Adhesives & Sealants

UV Curable Epoxy Resin exhibits 2-3% shrinkage upon cure.

Suited for bonding, sealing, and coating, UV16 single-component, epoxy resin based polymer system bonds to plastics, glass, ceramics, and metals. Product is 100% reactive and does not contain any solvents or other volatiles. With operating temperature range of -60 to +300°F, resin has glass transition temperature over 125°C after post curing at 90 to 125°C for 30 min. It cures...

Read More »

All Topics