Master Bond, Inc.

Epoxy Adhesive is chemical and temperature resistant.
Adhesives & Sealants

Epoxy Adhesive is chemical and temperature resistant.

Formulated to withstand repeated cycles of steam, ethylene oxide, radiation, and chemical sterilization, EP62-1MED 2-component epoxy adhesive system cures at 150-200°F temperatures and is serviceable up to 400°F. USP Class VI approved adhesive contains no solvents or volatiles and has 100:10 mix ratio by weight. Available in pint, quart, 1 and 5 gal kits, product exhibits less than...

Read More »
Epoxy Adhesive acts as electrical insulator.
Adhesives & Sealants

Epoxy Adhesive acts as electrical insulator.

Model EP21 2-component, room temperature curing, epoxy adhesive allows adjustment of properties by altering mix ratio. Adhesive holds up to thermal cycling and resists chemicals including water, oils, fuels, acids, bases, and salts. With gap filling properties and operating temperature of -60 to 250°F, adhesive bonds to variety of substrates and does not contain any diluents or solvents.

Read More »
Adhesive/Sealant offers long-term storage capability.
Adhesives & Sealants

Adhesive/Sealant offers long-term storage capability.

Master Bond Polymer System Supreme 10HTFL is single-component, epoxy resin-based adhesive/sealant with -300 to +300°F service temperature range. Cured to flexible thermoset polymer at temperatures of 250-300°F and above, product does not require refrigeration for extended storage before use. It adheres to metallic and non-metallic substrates, even upon prolonged exposure to hostile...

Read More »
Silicone Polymer Compound cures with UV or RTV.
Adhesives & Sealants

Silicone Polymer Compound cures with UV or RTV.

Formulated to react with UV light and atmospheric humidity, UV71DC is suited for applications involving complex product geometries. Single-component product cures to produce optically clear, flexible, non-yellowing, and chemically resistant adhesive, sealant, or coating. Employed over -80 to +400°F range, compound exhibits thermal shock resistance and adheres to substrates from glass and...

Read More »
Sealant has -300 to 600°F service temperature range.
Adhesives & Sealants

Sealant has -300 to 600°F service temperature range.

One component, heat curing epoxy adhesive/sealant EP17 cures at temperatures from 300-350°F for 60-90 minutes. Flowable paste has 8,700 psi tensile strength, 387,000 psi tensile modulus, Shore D hardness greater than 90, and compressive strength greater than 13,000 psi. MIL-MMM-A-132 compliant, 100% reactive compound is resistant to chemicals, including fuels and acids, and bonds to metals,...

Read More »
Two-Part Epoxy features low exotherm during cure.
Adhesives & Sealants

Two-Part Epoxy features low exotherm during cure.

Master Bond Polymer System EP37-3FLSP bonds to substrates such as metals, glass, ceramics, plastics, and elastomers. Optically clear epoxy features electrical insulation properties and exhibits resistance to vibration, shock, and thermal cycling. Suited for large-volume castings, product has 20 Shore D hardness, 1,000 psi tensile strength, and over 400 V/mil dielectric strength. Pot life after...

Read More »
Epoxy Adhesive meets NASA low outgassing specifications.
Adhesives & Sealants

Epoxy Adhesive meets NASA low outgassing specifications.

Formulated to setup in 3-5 min in 10-20 g masses at room temperature, EP65HT-1 ultra-fast curing, high temperature resistant epoxy adhesive bonds with metals, glass, ceramics, woods, vulcanized rubbers, and plastics. It has Shore D hardness of >75 and volume resistivity of >1014 ohm-cm. Mixed viscosity is 60-70,000 cps and mix ratio is 10 to 1 by weight. Available in pint, quart, gal, and 5 gal...

Read More »
Reworkable UV Adhesive is removable by most solvents.
Adhesives & Sealants

Reworkable UV Adhesive is removable by most solvents.

Flexible, one-component UV14-3 Polymer Adhesive is 100% reactive with moderate viscosity at ambient temperatures, and does not contain any solvents or other volatiles. Cured in section thicknesses up to 1/8 in. deep, non-yellowing formula is not oxygen inhibited and can be used as adhesive, sealant, and coating at temperatures from -60 to +250°F. Flexibility imparts vibration and shock...

Read More »
Adhesives & Sealants

Epoxy Adhesive has tensile shear strength of 2,000 psi.

Two component, room temperature curing, nickel filled, electrically conductive EP76M epoxy adhesive features thermal conductivity of 8-9 Btu/in/ftÂ-²/hr/°F. Featuring one to one mix ratio by weight or volume, it offers 5-10 ohm-cm volume resistivity. EP76M exhibits 30 in/in x 106/°C thermal expansion coefficient, and service operating temperature range of -60 to +250°F....

Read More »
Adhesives & Sealants

Polymer Adhesive has flexible, low-viscosity formula.

Designed for bonding, sealing, and casting engineering plastics and metals, EP40 cures at ambient or elevated temperatures with 1:1 mix ratio by weight or volume. Flexible, 2-component epoxy resin compound is resistant to thermal cycling as well as mechanical vibration and shock. Shear and peel strengths for bonding polycarbonates are 1000 psi and 20 pli, respectively, while steel and aluminum...

Read More »

All Topics