Glenro, Inc.
Paterson, NJ 07501
Infrared System heat-shrinks FEP tubing on catheters.
Automated system employs Radround(TM) IR heater rated at 2 kW and mounted on vertical axis. Heater has cylindrical inner quartz core that produces uniform IR heat, while thermocouple feedback control loop allows for temperature control. System measures 11 x 2.75 x 2.5 ft and accommodates motorized mandrel/cable hoist to automate product feed. Integral control system is mounted in a NEMA 12...
Read More »
Conveyorized Coater/Dryer offers speeds up to 20 ipm.
Model 4246 dip coater and infrared dryer system dip coats printed circuit boards in protective conformal coatings, and dries coatings at rates between 2-20 ipm. Stainless steel dip tank includes recirculation and filtration system to maintain quality of conformal coating. Dryer section consists of 6 Glenro Radplane(TM) Series 36 low-temperature electric infrared heaters, which are regulated in...
Read More »
Predryer handles woven fabrics before they enter tenter.
Gas Infrared Predryer, measuring 11 x 7 x 4 ft, predries dyed woven fabrics from 52-65 in. wide before they enter main tenter range. Ten Radplane(TM) gas infrared heaters, rated at 332,904 BTU/hr each, are mounted on 2 vertical structural steel frames to form 2-pass gas infrared oven. Insulated, adjustable reflectors at predryer's entrance and exit minimize ambient air infiltration. Electrical...
Read More »
IR Curing Tower improves manufacturing of medical tubing.
Infrared tower uses 2 Radround(TM) short wave IR heaters and drive system to cure silicone tubing at adjustable rates. Heaters have clamshell design and consist of rapid-response T3 lamps. Focused, 91.2 kW IR heat ensures tubing reaches green strength. Ready for product processing almost immediately on power-up, it cools fast enough so that product is not damaged when line stops. Parabolic...
Read More »
Conveyor Oven dries products up to 65 in. wide.
Infrared Conveyor Oven features bank of 6 Radplane(TM) electric infrared heaters rated at 9.8 kW each, controlled in single zone, for total power of 58.8 kW. Air input plenum provides air across full width of heated area. Temperature is regulated by SCR control system, housed in NEMA 12 enclosure, that uses thermocouple feedback control loop to regulate voltage and maintain constant element...
Read More »
Infrared Oven speeds wire processing.
Infrared Oven preheats fine-gauge and braided wire prior to fluoropolymer extrusion. Cylindrical Radround(TM) Series 40 electric infrared heaters incorporate quartz tubes that keep heat in process area. Oven packs 3 kW of power and measures 1.5 ft wide x 4 ft high. CS2000 controls use SCRs to regulate power input to infrared heating elements via thermocouple feedback control loops. Temperatures...
Read More »
IR Conveyor Oven suits cleanrooms and food processing.
Stainless steel electric infrared oven, rated at 58.32 kW, measures 9.75 x 5.5 x 5.5 ft and is mounted on casters. Its 36 in. wide wire conveyor belt moves product through oven at rates from 4-40 fpm, while 36 medium wave quartz tube IR heaters with gold reflective backing provide cleanroom-quality heat transfer. There is 22 in. of conveyor at entrance and exit ends, and double-wall construction...
Read More »
Infrared System heat-shrinks FEP tubing on catheters.
Automated system employs Radround(TM) IR heater rated at 2 kW and mounted on vertical axis. Heater has cylindrical inner quartz core that produces uniform IR heat, while thermocouple feedback control loop allows for temperature control. System measures 11 x 2.75 x 2.5 ft and accommodates motorized mandrel/cable hoist to automate product feed. Integral control system is mounted in a NEMA 12...
Read More »
Conveyorized Coater/Dryer offers speeds up to 20 ipm.
Model 4246 dip coater and infrared dryer system dip coats printed circuit boards in protective conformal coatings, and dries coatings at rates between 2-20 ipm. Stainless steel dip tank includes recirculation and filtration system to maintain quality of conformal coating. Dryer section consists of 6 Glenro Radplane(TM) Series 36 low-temperature electric infrared heaters, which are regulated in...
Read More »
Predryer handles woven fabrics before they enter tenter.
Gas Infrared Predryer, measuring 11 x 7 x 4 ft, predries dyed woven fabrics from 52-65 in. wide before they enter main tenter range. Ten Radplane(TM) gas infrared heaters, rated at 332,904 BTU/hr each, are mounted on 2 vertical structural steel frames to form 2-pass gas infrared oven. Insulated, adjustable reflectors at predryer's entrance and exit minimize ambient air infiltration. Electrical...
Read More »
IR Curing Tower improves manufacturing of medical tubing.
Infrared tower uses 2 Radround(TM) short wave IR heaters and drive system to cure silicone tubing at adjustable rates. Heaters have clamshell design and consist of rapid-response T3 lamps. Focused, 91.2 kW IR heat ensures tubing reaches green strength. Ready for product processing almost immediately on power-up, it cools fast enough so that product is not damaged when line stops. Parabolic...
Read More »
Conveyor Oven dries products up to 65 in. wide.
Infrared Conveyor Oven features bank of 6 Radplane(TM) electric infrared heaters rated at 9.8 kW each, controlled in single zone, for total power of 58.8 kW. Air input plenum provides air across full width of heated area. Temperature is regulated by SCR control system, housed in NEMA 12 enclosure, that uses thermocouple feedback control loop to regulate voltage and maintain constant element...
Read More »
Infrared Oven speeds wire processing.
Infrared Oven preheats fine-gauge and braided wire prior to fluoropolymer extrusion. Cylindrical Radround(TM) Series 40 electric infrared heaters incorporate quartz tubes that keep heat in process area. Oven packs 3 kW of power and measures 1.5 ft wide x 4 ft high. CS2000 controls use SCRs to regulate power input to infrared heating elements via thermocouple feedback control loops. Temperatures...
Read More »
IR Conveyor Oven suits cleanrooms and food processing.
Stainless steel electric infrared oven, rated at 58.32 kW, measures 9.75 x 5.5 x 5.5 ft and is mounted on casters. Its 36 in. wide wire conveyor belt moves product through oven at rates from 4-40 fpm, while 36 medium wave quartz tube IR heaters with gold reflective backing provide cleanroom-quality heat transfer. There is 22 in. of conveyor at entrance and exit ends, and double-wall construction...
Read More »