Dymax Corp.
Torrington, CT 06790
Needle-Bonding Adhesives increased throughput via cure speed.
With typical cure time of 2.5 sec or less, 1400 Series LED-curable needle bonders increase production speed and throughput while promoting quality control with aid of fluorescing technology. Adhesives cure with 385 or 405 nm wavelengths, allowing design flexibility within automation process, and are available in 15 L pails.- Products pass ISO 10993-5 Cytotoxicity testing and support short-term (
Read More »UV Light-Curing Flood-Lamps are CE-marked for global use.
Designed to optimize safety for process-controlled cures, ECE Series is capable of curing adhesives, coatings, and inks. Lamps are suitable for curing parts with large bond lines or for simultaneously curing of multiple parts in trays. Modular units consist of power supply, reflector housing, and 400 W metal halide UV-curing bulb. By adding accessories such as UV shielding and shutter assemblies,...
Read More »
FIP/CIP Gasket helps eliminate adhesion loss-induced failures.
Intended for fuel cell sealing applications, Ultra Light-Weld-® GA-145 UV/Visible light-curable Form-In-Place (FIP) and Cure-In-Place (CIP) gasket is formulated to be tack free, soft, and flexible with low outgassing after cure. Chemical-resistant product, which- can be dispensed in intricate and complex configurations, supports- in-line curing and bonds to metals, glass, and PC. Gasket cures...
Read More »
LED Curable Coating targets medical micro circuits.
Developed to be tack-free after curing, MD-® 1901-M helps prevent potential defects that could occur from components being handled too soon.- Flexible product- is ISO-10993-5 approved for customers who are looking for medical grade electronics coating, seal, or moisture barrier. Able to resist cracking or delamination while board is being flexed, low-durometer coating is suited for circuits...
Read More »
Adhesive is resistant to high temperature and moisture.
Intended for glass-to-glass and glass-to-metal applications, Ultra Light-Weld-® 431 can be used in high-temperature and high-moisture environments while maintaining adhesion and flexibility. Product bonds upon exposure to UV/Vis light for immediate use in assembly process, and minimal shrinkage reduces stress on bond line or larger cured surfaces. This adhesive may also be considered for use in...
Read More »
Water-Dilutable Oligomer exhibits water resistance after cure.
Providing water-barrier coating with anti-fogging characteristics, Bomar™ XR-9416 contains no water but is infinitely dilutable. Uncured 100%-solids material has viscosity of 7,000 cP at 25-
Read More »Conformal Coating eliminates need for additional processing.
Specially formulated to cure in shadowed areas underneath components on printed circuit boards, Dual-Cure 9482 is tack-free immediately after curing, helping to avoid defects such as fingerprints. Light- and moisture-cure coating is engineered for thicknesses up to 0.010 in. and demonstrates optimal re-workability. Fluorescing vivid blue when exposed to UV light, 9482 enables obvious detection of...
Read More »
Hand-Held Spray Guns handle medium- and high-viscosity fluids.
Available in standard- and high-flow models, Series SG-100 facilitates manual spraying of materials for masking and coating applications. Pneumatically operated systems can dispense from pressurized cartridges, bottles, and pails. All wetted components are stainless steel, Teflon-®, or Kalrez-® for compatibility with variety of fluids. With adjustment of material flow and spray atomization,...
Read More »
Valve Dispensing System is built for accuracy, consistency.
Utilizing pneumatic, NC diaphragm valve, Model 475 dispenses low- to high-viscosity fluids. Design of internal diaphragm and adjacent parts prevents migration of fluid into actuating section within valve, while diaphragm toughness and materials selection for component construction promote extended life between maintenance schedules. Along with 25 micron air filter regulator, features include...
Read More »
Strippable Mask for Electronic Applications Cures in Seconds to Maximize Production Speed
Easily dispensed for accurate placement Torrington, Connecticut - Dymax Corporation's Ultra Light-Weld-® 9-20479-B is a blue, peelable masking material that cures in seconds when exposed to UV/Visible light. This material is designed for rapid masking of electronic components and assemblies, provides protection from reflow or wave soldering operations, and shields keep-out areas during conformal...
Read More »