Mill-Max Mfg. Corp.
Oyster Bay, NY 11771
New Omniball Spring-Loaded Contact Features Barb and Knurl Press-fit
Rolling ball interface feature enables mating components to engage in lateral, rotational and angular alignments. Includes .030” (.762 mm) maximum stroke; gold plating on all components and a .091” diameter ball interface. Tested to 1,000,000 compression cycles and rolled over 67 miles (108 km) at half stroke.
Read More »
New Spring-loaded Pins Deliver High Current Carrying Capacity
Available in three different termination styles such as surface mount, through-hole and solder cup. Includes gold plating on all components, cycle life rating of 1,000,000 at half stroke, contact resistance of 20m-ohms max and spring force of 60 grams at mid stroke. Ideal for charging applications as well as for directly delivering power via cable or board-to-board interconnects.
Read More »
New SMT Discs Machined from Brass
Includes 1593, 1618, 1625 and 1656-X SMT discs with diameters of 0.093", 0.118”, 0.125” and 0.156" respectively. Comes standard with a 10 u" hard gold finish with a nickel under-plate. Ideal for surface mount soldering and as the conductive mating surface for spring-loaded pins and connectors as well as test probes.
Read More »
New Omniball Spring-Loaded Contacts with 6.76 mm of Height
Available as individual pins and in a 4-pin circular connector which is offered in tubes and tape as well as in reel packaging. Features .030” maximum stroke, gold plating on all components and surface mount termination. Suitable for any application that involves sliding or rotating connections.
Read More »
New Crimp Pins and Receptacles are Ideal for Use in Cable Assembly Connectors
Available in broad range of wire sizes (16-24 AWG) and mating leads (.022 in. - .063 in.) . Precision-machined to exacting tolerances and gold plated for conductivity and durability. Can be used to terminate discrete wires, such as in board-toboard or intra-board connections for power or signal.
Read More »
New Spring-Loaded Connectors Eliminate Stray Currents from Damaging Devices
First Mate/Last Break connectors feature spring pins with precision-machined external components and high reliability internal springs. Connector housings are molded from high-temperature thermoplastic and suitable for most soldering processes. Support applications where electrical signals must be made and broken in sequence rather than all at once, such as in hot swapping or hot plugging.
Read More »
New Pre-Wired Spring-Loaded Connectors with PVC Insulation and 7/32 Stranding
867-22-002-70-501010 connector features precision-machined and gold-plated spring pins on 0.100” (2.54 mm) centers. Combines high quality mill-max spring-loaded pogo pins with the convenience of a 12” pig-tail to suit a wide variety of applications. Each wire end is stripped to a length of 0.140” with slug on to prevent fraying.
Read More »
New Receptacles Designed to Work with Shorter Mating Leads
Designed to be soldered in a .071” minimum mounting hole. Fitted with beryllium copper contact clip. Accepts lead diameters from .037” - .043” with minimum mating lead length of .058” for top entry insertion.
Read More »
New Compression Style Spring-loaded Connectors Include Two Active Plungers
Ideal for situations in which a soldered connection is not desirable or may not be possible due to design constraints. Incorporates spring pins with active plungers at each end. Connector is sandwiched between two mating surfaces using screws to compress the plungers on the base end, eliminating the need for soldering.
Read More »
New Solder Cup from Mill Max Delivers Flexible Array of Solutions for Wire Termination Requirements
Suitable for spacing, height and orientation requirements. Features include discrete receptacles, terminal pins, spring-loaded pins, standard .100” pitch headers, sockets and spring-loaded connectors. Configurations are .050” and 2 mm pitch headers with straight and right-angle solder tail options, .050” pitch sockets, .050” pitch spring-loaded connectors and .100” pitch low profile...
Read More »
New Omniball Spring-Loaded Contact Features Barb and Knurl Press-fit
Rolling ball interface feature enables mating components to engage in lateral, rotational and angular alignments. Includes .030” (.762 mm) maximum stroke; gold plating on all components and a .091” diameter ball interface. Tested to 1,000,000 compression cycles and rolled over 67 miles (108 km) at half stroke.
Read More »
New Spring-loaded Pins Deliver High Current Carrying Capacity
Available in three different termination styles such as surface mount, through-hole and solder cup. Includes gold plating on all components, cycle life rating of 1,000,000 at half stroke, contact resistance of 20m-ohms max and spring force of 60 grams at mid stroke. Ideal for charging applications as well as for directly delivering power via cable or board-to-board interconnects.
Read More »
New SMT Discs Machined from Brass
Includes 1593, 1618, 1625 and 1656-X SMT discs with diameters of 0.093", 0.118”, 0.125” and 0.156" respectively. Comes standard with a 10 u" hard gold finish with a nickel under-plate. Ideal for surface mount soldering and as the conductive mating surface for spring-loaded pins and connectors as well as test probes.
Read More »
New Omniball Spring-Loaded Contacts with 6.76 mm of Height
Available as individual pins and in a 4-pin circular connector which is offered in tubes and tape as well as in reel packaging. Features .030” maximum stroke, gold plating on all components and surface mount termination. Suitable for any application that involves sliding or rotating connections.
Read More »
New Crimp Pins and Receptacles are Ideal for Use in Cable Assembly Connectors
Available in broad range of wire sizes (16-24 AWG) and mating leads (.022 in. - .063 in.) . Precision-machined to exacting tolerances and gold plated for conductivity and durability. Can be used to terminate discrete wires, such as in board-toboard or intra-board connections for power or signal.
Read More »
New Spring-Loaded Connectors Eliminate Stray Currents from Damaging Devices
First Mate/Last Break connectors feature spring pins with precision-machined external components and high reliability internal springs. Connector housings are molded from high-temperature thermoplastic and suitable for most soldering processes. Support applications where electrical signals must be made and broken in sequence rather than all at once, such as in hot swapping or hot plugging.
Read More »
New Pre-Wired Spring-Loaded Connectors with PVC Insulation and 7/32 Stranding
867-22-002-70-501010 connector features precision-machined and gold-plated spring pins on 0.100” (2.54 mm) centers. Combines high quality mill-max spring-loaded pogo pins with the convenience of a 12” pig-tail to suit a wide variety of applications. Each wire end is stripped to a length of 0.140” with slug on to prevent fraying.
Read More »
New Receptacles Designed to Work with Shorter Mating Leads
Designed to be soldered in a .071” minimum mounting hole. Fitted with beryllium copper contact clip. Accepts lead diameters from .037” - .043” with minimum mating lead length of .058” for top entry insertion.
Read More »
New Compression Style Spring-loaded Connectors Include Two Active Plungers
Ideal for situations in which a soldered connection is not desirable or may not be possible due to design constraints. Incorporates spring pins with active plungers at each end. Connector is sandwiched between two mating surfaces using screws to compress the plungers on the base end, eliminating the need for soldering.
Read More »
New Solder Cup from Mill Max Delivers Flexible Array of Solutions for Wire Termination Requirements
Suitable for spacing, height and orientation requirements. Features include discrete receptacles, terminal pins, spring-loaded pins, standard .100” pitch headers, sockets and spring-loaded connectors. Configurations are .050” and 2 mm pitch headers with straight and right-angle solder tail options, .050” pitch sockets, .050” pitch spring-loaded connectors and .100” pitch low profile...
Read More »
