Teledyne LeCroy Corporation

Software

Design Verification Software provides PCIe 3.0 protocol testing.

Addressing pre-silicon simulation and design verification phases of development, SimPASS allows RTL simulation vector files that describe PCI Express 3.0 I/O traffic in pre-silicon phase to be displayed and analyzed in same way as hardware-derived trace files in post-silicon phase. By extracting features that show potential flaws in data and transaction packets from I/O stream, SimPASS enables...

Read More »
Laboratory and Research Supplies and Equipment

Protocol Tester supports PCI Express® 3.0.

Able to assist developers working on PCIe-® 3.0 designs, Summit(TM) Z3-16 offers testing capabilities for developing script level traffic generation as well as range of pre-programmed manual test features for root complex and end point device testing. Features that include recreating ACK latencies, manual error injection, end point and host emulation, as well as capture/playback of traces taken...

Read More »
Test & Measurement

Oscilloscopes facilitate design, debug, and troubleshooting.

Available in bandwidths from 60-300 MHz, 4-channel WaveAce(TM) Oscilloscopes provide sample rate up to 2 GS/s and up to 10 kpts/ch memory, while 2-channel, 40 MHz model provides sample rate up to 500 MS/s and 4 kpts/ch memory. Units feature 32 built-in automated parameters and internal storage that holds up to 20 waveforms and 20 setups. With USB host and device ports, plus LAN connection,...

Read More »
Fluid & Gas Flow Equipment

Mid-Bus Probe supports PCI Express® 3.0 specification.

Mid-bus probe for Summit(TM) T3-16 Protocol Analyzer supports 8 GT/sec data rates of PCI Express 3.0 specification and can be connected to systems that utilize Intel-® mid-bus probe footprint specification. Probe uses full-size connector that supports PCIe-® x8 lanes, and 2 probes can be connected to analyzer to support x16 lane widths. Ability to be used in conjunction with lane swizzling...

Read More »
Fluid & Gas Flow Equipment

Mini Card Interposer speeds Gen2 PCI Express® analysis.

Accommodating 2 types of setups, Mini Card Interposer serves as dedicated probe that makes it possible to analyze data traffic from Mini Card that uses PCIe interface to connect to laptop/notebook/tablet system. It supports probing at speeds up to 5 GT/s (Gen2) and, in addition to being able to probe PCIe interface, also provides connectivity to LeCroy's USB analyzers for USB 2.0 protocol...

Read More »
Laboratory and Research Supplies and Equipment

LeCroy First to Ship PCI Express 3.0 Protocol Analyzer

Santa Clara, CA - LeCroy Corporation, a leading supplier of serial data test solutions, today announced the first shipments of PCI Express-®: 3.0 Protocol Analyzers in the protocol test equipment industry. The new Summit(TM) T3-16 is LeCroy's fifth generation of protocol analyzers targeted at high speed PCI Express I/O-based applications. The LeCroy Summit T3-16 captures, decodes and analyzes...

Read More »
Controls & Controllers

Mezzanine Card Interposer facilitates PCIe 2.0 analysis.

Designed for Summit(TM) PCI Express Protocol Analyzers, XMC Mezzanine Card Interposer provides dedicated probe that enables users to analyze data traffic from XMC module that uses PCI Express interface to connect to carrier board system. Card supports PCI Express data channels with lane widths up to x8 at data rates up to 5 GT/s. With protocol analyzers, users can identify, diagnose, and solve...

Read More »
Architectural & Civil Engineering Products

DDR3 Compliance Test Package enables high-speed evaluation.

QualiPHY automated serial data compliance test solutions include support for DDR3 via full suite of Clock, Electrical, and Timing tests as defined by JESD79-3D JEDEC specification. Available for WavePro 7 Zi and WaveMaster 8 Zi oscilloscopes, QualiPHY DDR3 can perform measurements on 800, 1,066, 1,333, and 1,600 MHz DDR3 signals as well as custom speed grades. It also enables debug capability for...

Read More »
Software

Compliance Test Software targets USB 3.0 protocol.

Built on Voyager protocol verification platform, Compliance Test Suite for USB 3.0 provides automated, turnkey test application that allows device vendors to begin pre-testing SuperSpeed USB designs in advance of industry's certification program. Software addresses Command Layer and Link Layer compliance verification, including Chapter 9 framework tests for USB 2.0 and 3.0 devices. Console steps...

Read More »
Fluid & Gas Flow Equipment

Circuit Test Probe monitors embedded USB 2.0 and inter-chip links.

USB probe monitors embedded USB 2.0 and interchip links within multichip PCB assembly. Operating with entire line of LeCroy USB analyzers, probe supports tapping chip-to-chip links using low or full speed inter-chip signaling at all defined IC-USB voltages. Flying lead tap can be connected directly to inter-chip probe points using solder-in resistor connections. Probe can also be used to tap USB...

Read More »

All Topics