Murata Power Solutions
Mansfield, MA 02048
Image Signal Processor offers single-chip solution.
Application-specific ADCDS-1410, suited for electronic-imaging applications that employ CCDs as photodetector, delivers 14-bit resolution and throughput rate of 10 Megapixels/sec. Utilizing multi-process technologies, product combines mixed-signal ICs and passive components in 800 mW typ solution with signal-to-noise ratio of 73 dB min. Its 40-pin TDIP package incorporates user-configurable input...
Read More »
Transformers measure and monitor ac currents.
Combining isolation voltage of 500 Vdc and primary current rating of 10 A, 5600 range of current sensing transformers are available in 50, 100, 200, and 300 turn variants. Center tapped versions are available, reducing component count in full wave analysis configuration. Products have operating frequency range of 20-200 kHz, and, when used in switched mode power supplies, act as feedback elements...
Read More »
DC/DC Converters use synchronous rectifier technology.
Producing 6 A output currents and 10.8-19.8 W of power, NPX20 series single-output, isolated converters are available in 3 pin patterns. Surface mount and through hole converters are offered with choice of 2 input voltage ranges: nominal 24 V input devices accommodate voltages from 18-36 V, while nominal 48 V input parts accept voltages from 36-75 V. Output voltage options are 1.8, 2.5, and 3.3...
Read More »
Voltage Regulators help maximize battery life.
Supplied in TO-220 SIP packaging, step-down Series 78SR is pin- and size-compatible with LM78xx devices. Three models offer outputs of +5 V/0.5 A, +12 V/0.4 A, and +3.3 V/0.5 A. Switching frequency of 260 kHz produces efficiencies as high as 95% for 12 V part and 85% for 3.3 and 5 V regulators. Offering full load operation from 9, 12, 24, 28, or 36 V supplies, at ambient temperatures as high as...
Read More »
POL Converter powers DDR2 memory up to 75 A.
From 12 Vdc input, non-isolated Model VCN75-018V provides programmable output of 1.7-1.95 Vdc with full-load efficiency of 85%. Unit has maximum input current of 16.0 A, no-load input current of 300 mA, and minimal output voltage ripple and noise of 50 mV p-p at 20 MHz. Supplied in vertical-mount 22-pin SIP, Model VCN75-018V includes remote sense, output enable, and power good signal. Turn on...
Read More »
POL Converters support intermediate bus converters.
Available in packages with surface mount, open frame, PTH design, NFA Series DC-DC converters come in 10, 16, and 20 A models. Non-isolated Point-Of-Load converters, featuring efficiencies up to 95%, come in positive and negative enable logic models with monotonic start-up with pre-bias. With input voltage range of 6-14 V, products support 4:1, 5:1, and 6:1 intermediate bus converters. Series...
Read More »
Sampling ADCs feature noise levels to 150 -µVrms.
Analog-signal-processing (ASP), multi-chip ADSD-1410 uses active laser trimming of thin-film resistors, weaving different semiconductor chips into one ASP function. It has 2 input channels, wideband (30 MHz) sample-hold amplifiers, and independently clocked, 14-bit, 10 MSPS ADCs. Housed in 28-pin, double-DIP, ceramic package, unit employs proprietary gate array that provides timing and control...
Read More »
Configurable Dual Winding Inductors provide EMI shielding.
SMT inductors in 4700 and 4800 series are bobbin format devices with 1:1 winding ratio that can be connected in series or parallel for range of inductance combinations. With respective heights of 5.0 and 6.2 mm, 4700 and 4800 series incorporate integral EMI shield and offer nominal inductance values from 1.0-400 Ã-µH @ 10 kHz and 100 mVac. Devices in 4700 series handle max continuous current...
Read More »
Non-Isolated DC/DC Converters offer 10 A output.
Available in 16 models, NNL10 series point of load (PoL) DC/DC converters address voltage and current requirements of high-performance FPGAs, ASICs, DSPs, and microprocessors. SMD devices operate with voltage input from 3.0-5.5 V and are available with output voltages of 0.9, 1.0, 1.2, 1.5, 1.8, 2.0, 2.5, and 3.3 V. Each unit offers continuous short circuit protection, under voltage lockout, and...
Read More »
DC/DC Converters have user-programmable output voltages.
Offered in vertical or horizontal orientations, LSN-16A Series enables true point-of-use (point-of-load) power processing. Non-isolated power converters accept 3.3/5 V inputs for W3 models and 12 V inputs for D12 models and deliver 0.75/1/1.2/1.5/1.8/2/2.5/3.3/5 V outputs, fully rated at 16 A. Fixed-frequency, 220/300 kHz, synchronous buck topologies deliver conversion efficiencies to 96% with...
Read More »