Kistler Instrument Corp.
Amherst, NY 14228
Contact Elements help transmit pressure signals within injection molds.
Contact elements Type 1712A... and Type 1714A... facilitates transmission of pressure signals within injection molds by providing electrical connection between cables in different mold components. During mold assembly, these cables are connected via contacts of both elements. Products eliminate need for sensor cables to be guided through several mold plates and support 1- or 4-channel elements,...
Read More »
Multichannel Charge Amplifier targets laboratory applications.
Intended for mounting in 19 in. racks, Type 5080A features modular design that allows expansion to 8 amplifier modules. Unit can accommodate both charge modules for piezoelectric sensors and dual-mode modules with charge/Piezotron® input, enabling acquisition of force signals as well as signals from sensors measuring pressure, torque, or acceleration. Featuring frequency range of 0-200+...
Read More »
Wheel Force Transducer suits fuel-efficient cars.
RoaDyn® S615 System 2000 6-component unit is based on 3 load cell concept and features carbon fiber reinforced plastic rim, rim ring, and wheel disk. Device allows maximum vertical load Fz of approximately 15 kN. Mounted on vehicle as complete wheel, it measures forces Fx, Fy, and Fz and torques Mx, My, and Mz on rotating wheel. Measurement signals are converted to digital in wheel...
Read More »
Triaxial Force Sensors measure from ±1.8k to ±33.7k lbf.
Three-component triaxial force links are fully calibrated and preloaded for dynamic force measurements in 3 orthogonal directions, in both tension and compression modes, across various applications and regardless of acting point of force. All dynamic sensing elements are located in rust-free, sealed, stainless steel housing. Type 9327C triaxial quartz force link includes rigid construction and...
Read More »
Measuring Hub for Tire Test Stands meets resistance standards.
Featuring 2-component design, RoaDyn® S220 measuring hub Type 9289A103 measures changes in rolling resistance in tangential direction Fx as close as possible to tire footprint. Use of strain gage technology allows static measurement of contact force Fz and control of test stand. Reliant upon force measurement method, product meets requirements of rolling resistance standards ISO 28580, SAE...
Read More »
Ethernet Interface for RoaDyn® System 2000 Allows Evaluation of Measurement Data from Wheel Force Transducers with SCADAS Durability Recorder from LMS
Measurement data from Kistler wheel force measuring systems can now also be recorded and evaluated with the SCADAS Durability Recorder, a mobile data acquisition system from LMS. LMS has developed the Wheel Force Transducer Module (WF12) for connecting Kistler's electronic RoaDyn System 2000. The System 2000 acquires and transfers data from Kistler's wheel force measuring systems and can be...
Read More »
Tension/Compression Sensors have ±8 kN measuring range.
Preloaded in 42 x 42 x 42 mm sealed, stainless-steel housing, 3-component type 9327C Force Link sensors measure tension and compression forces regardless of point of application. Measurement ranges are Fx,y = ±4 kN and Fz = ±8 kN, and design is intended to reduce crosstalk as well as hysteresis. Operating from -40 to +120°C, sensors use V3 multipole connector and are available...
Read More »
Triaxial Accelerometer features low-mass design.
Type 8688A IEPE triaxial accelerometer simultaneously measures vibration in 3 orthogonal axes. Unit incorporates Kistler PiezoBeam® technology, with ceramic cantilevered beam enclosed within lightweight welded titanium housing. Low-noise charge amplifier and 4-pin connector, for mounting in confined areas, are included. Operating from internal power source found in most FFT analyzers,...
Read More »
Torque Sensor features contact-free signal transmission.
Based upon strain gage technology, type 4520A torque sensor measures torques in accuracy class 0.5 at speeds up to 10,000 rpm. It is offered with torques of 1, 2, 5, 10, 20, 50, 100, 200, 500, 1,000 Nm and features ±10 V torque signal, speed output with 60 pulses/rev, and externally switchable control signal. Suited for use in production, quality control, and laboratory, sensor is...
Read More »
Press Force Sensors feature 3 calibrated measuring ranges.
Type 9383A piezoelectric press force sensors feature calibrated measuring ranges of 0-3, 0-30, and 0-300 kN for measuring dynamic and quasistatic forces. Force acting on quartz element generates proportional electric change at output, which is converted by connected in-line charge amplifier into process signal. Unit features flange connections at both ends, centering rings for axial adjustment,...
Read More »
