Kistler Instrument Corp.
Amherst, NY 14228
Sensor Amplifiers support industrial process monitoring.
Type 5030A MiniAmp series of sensor amplifiers measures less than 1.5 in. square and can be mounted close to sensor on moving machinery components. Amplifier inputs accept any piezoelectric sensor operating in high impedance, charge mode. Momentary data events are reproduced due to wide bandwidth, and with 2 measuring ranges, products can be digitally switched while in operation. Enclosure is...
Read More »Pressure Sensing System suits polymer molding process.
Consisting of piezoresistive pressure sensor and digital charge amplifier, 4079A series enables measurement of cavity pressure in polymer molding with long cycle times. With ability to be integrated into injection molding machines, sensors record reaction temperatures and are free of harmful media. Versions are available for 5, 10, 20, and 50 bar pressure ranges in applications to 180Ã-
Read More »Calibration Systems suit testing facilities and laboratories.
Accelerometer calibration systems line includes 8802A Laboratory Calibration Reference Standard System and 8804A Laboratory Vibration Calibration System and features 5022 frequency compensated charge amplifier. Systems exhibit repeatability from 10-10,000 Hz over wide amplitude range, and are calibrated for sensitivity of 10 mV/g that is adjustable to tolerance of Ã-
Read More »Software optimizes injection molding quality.
DataFlow(TM) v2.3 molding process analysis software, type 2805A, includes provision that permits split operation into set-up mode and utilizes data compression technology to facilitate data processing. While floating tolerance band accommodates sporadic disruptions, filter features can be used during offline phase to aid with analysis and generation of software configurations. Off-line graphics...
Read More »Pressure Sensor offers 2 mounting options.
With features that simplify between-run inspections and protect wiring, 6155AE cavity pressure sensor may be mounted by adapter on baseplate to permit separation of mold insert without disassembly of sensor. Alignment guide holes permit precise positioning. Secondary approach for alternate mold configurations makes use of sleeve to retain sensor. Sensor uses single conductor wire that maybe...
Read More »Accelerometers measure slow-moving events.
Supplied in integral and unattached cable versions, K-BeamÃ-® 8310A25 and 8310A50 measure to 25 and 50 g respectively in slow-moving applications from 0-300 Hz. Products, used to measure tilt and other static or dynamic conditions, have micro-machined capacitive sensing element that provides stability over -40 to +185Ã-
Read More »Portable Meter aids in gasoline engine maintenance.
Equipped with LCD, 300 Hz Butterworth low pass filter, and RS-232 interface capability, Type 2515A1 engine peak meter simplifies maintenance and monitoring programs. Calculations include arithmetic mean value of peak pressure, standard deviation, steepest slope of pressure curve, and engine speed. Able to operate for 20 hr from 9 V battery, unit provides data storage for 36 successive pressure...
Read More »Engine Monitoring Sensors have minimum life of 16,000 hr.
Suited for monitoring cylinder pressure in stationary gas engines, sensor type 6613CA incorporates knock- and corrosion-resistant diaphragm as well as piezoelectric quartz measuring element that minimizes thermal shock and instability. Anti-strain internal design negates sensitivities to mounting stress and particulate contamination. Inline charge amplifier has 2 measuring ranges, to 100 and 250...
Read More »Foot Plates aid in rehabilitation of foot and leg.
Instrumentation grade Type 9281 and 9287B force plates incorporate piezoelectric force sensors with quartz crystals that convert force into data signal. Designed into foot tracks that don't reveal instrumentation beneath, patient steps, walks, or runs as instructed on outlined zone. Graduated force patterns visually represent physical condition, and impressions are captured for gait in motion...
Read More »Molding Pressure Sensors use single wire technology.
With respective front diameters of 4 and 6 mm, models 6157B and 6152A use single wire technology to speed in-the-mold pressure sensor installation for large plastics molds. Handling wire lengths up to 5 m, procedures such as shortening cables and attachment to connectors are accomplished without soldering. Push-on connectors enable slipping-in stripped wires to make connections. Sensors are...
Read More »