Minarik Corp.
Glendale, CA 91201
Share:
Regenerative Drive offers speed and torque control.
Rated to withstand 1 G of vibration, RG60U-T controls motors up to 2 hp and utilizes speed/torque adder card that enables velocity or torque control of motor. Enable and Inhibit terminals may be inverted, and invert jumpers choose whether drive runs or stops when terminals are opened or closed. Other features include choice of tachometer or armature feedback, 9 trimmer pots, and independently...
Read More »
DC Motor Control simultaneously operates 2 motors.
Microprocessor-based M2 drive can operate 2 DC motors at same time in independent or speed ratio mode. In independent mode, each side of M2 can be controlled with different trimmer pot settings and speeds; user chooses speed or torque control. In speed ratio mode, one speed potentiometer sets main speed while other determines ratio of speeds between motors. Drive is rated for 1 1/8 hp @ 115 Vac...
Read More »
Dual Voltage DC Drive includes speed and torque controls.
Capable of operating in speed or torque control mode, MM23002D series dual voltage drives are available in NEMA 1 and 4X models with wired and mounted operators and switches on front cover and AC line fuses inside. User-selectable inhibit modes enable users to choose whether inhibit function is activated by NO or NC condition. Jumper selects whether inhibiting directs motor to min speed or stop....
Read More »
Isolated DC Drive can control DC motors up to 2 hp.
Housed in NEMA 4X enclosure, Patriot Model MC10-PCM accepts any 0-10 V or 1-5 mA reference signal. Shunt resistor terminals are provided in case 4-20 mA or other current signal is to be used. Drive includes power and current limit LEDs, line fuses, and inhibit pins for remote start/stop control. Mounted on cover is speed adjust knob, on/off switch, and manual/signal switch. Drive has 1% speed...
Read More »
PWM Dual Voltage AC Drives include isolated front end.
Series VFD05-D230-PCM features minimum speed adjustment potentiometer, DC injection braking, and automatic or manual restarts. Available to 1.5 hp, drives can be used with 3-phase induction, single-phase PSC, shaded-pole, and synchronous motors. Doubling jumper can be set to output 230 Vac when only 115 Vac power supply is available. With automatic restart, inverter will restart after low voltage...
Read More »
Volts/Hertz AC Drive features isolated front end.
Dual voltage Model VFP4X04-D230-PCM includes minimum speed adjustment potentiometer, DC injection braking, and automatic or manual restarts. It can control variety of motors including 3-phase induction, single-phase permanent split capacitor, shaded pole, and synchronous motors. Doubling jumper can be set to output 230 Vac when only 115 Vac power is available. Offered to 1 hp, drive comes in...
Read More »
DC to DC Drive suited for battery-operated vehicles.
Series DC500 PWM Drive includes runaway and rollaway protection, battery under-voltage control, and protection from overheating. Programmable safety parameters are set via any terminal program on Windows-based PC. Temperature sensor on heatsink triggers warning signal with field current boosting and armature cutbacks at 60Ã-
Read More »
Variable Speed DC Drive controls 90 Vdc motors.
Mounted on unanodized chassis, EC2 series SCR drive provides features for driving 90 Vdc brush motors up to 5 A with 115 Vac power supply. Start-stop control is available through inhibit terminals, and set-up is accomplished using on-board trimmer pots to adjust for min speed, max speed, IR compensation, current limit, and acceleration/deceleration. Applications include conveying, material...
Read More »
DC Drive offers 1% speed regulation.
M1 DC drive is mounted on gold chassis and measures only 4.30 x 2.64 in. It is rated for 5 A (1/2 hp) with 115 Vac input and 10 A (1 hp) with addition of optional heatsink. Programmable chip sets range for acceleration, deceleration, current limit, and IR compensation trimmer pots. Inhibit function and jumper can adjust factory set trimmer pot ranges to fit smaller motors. M1 will follow...
Read More »
Regenerative Drive offers dual voltage (115/230 Vac) input.
RG60U is available for 1/8 to 1 hp motors, or up to 2 hp with optional heatsink. It includes enable and inhibit terminals with option to invert functions. Invert jumpers allow user to decide if drive runs or stops when terminals are opened or closed. RG60U offers tacho-generator or armature feedback, 9 trimmer pots, cage clamp and screw terminal blocks for secure connections, and current limit...
Read More »
Regenerative Drive offers speed and torque control.
Rated to withstand 1 G of vibration, RG60U-T controls motors up to 2 hp and utilizes speed/torque adder card that enables velocity or torque control of motor. Enable and Inhibit terminals may be inverted, and invert jumpers choose whether drive runs or stops when terminals are opened or closed. Other features include choice of tachometer or armature feedback, 9 trimmer pots, and independently...
Read More »
DC Motor Control simultaneously operates 2 motors.
Microprocessor-based M2 drive can operate 2 DC motors at same time in independent or speed ratio mode. In independent mode, each side of M2 can be controlled with different trimmer pot settings and speeds; user chooses speed or torque control. In speed ratio mode, one speed potentiometer sets main speed while other determines ratio of speeds between motors. Drive is rated for 1 1/8 hp @ 115 Vac...
Read More »
Dual Voltage DC Drive includes speed and torque controls.
Capable of operating in speed or torque control mode, MM23002D series dual voltage drives are available in NEMA 1 and 4X models with wired and mounted operators and switches on front cover and AC line fuses inside. User-selectable inhibit modes enable users to choose whether inhibit function is activated by NO or NC condition. Jumper selects whether inhibiting directs motor to min speed or stop....
Read More »
Isolated DC Drive can control DC motors up to 2 hp.
Housed in NEMA 4X enclosure, Patriot Model MC10-PCM accepts any 0-10 V or 1-5 mA reference signal. Shunt resistor terminals are provided in case 4-20 mA or other current signal is to be used. Drive includes power and current limit LEDs, line fuses, and inhibit pins for remote start/stop control. Mounted on cover is speed adjust knob, on/off switch, and manual/signal switch. Drive has 1% speed...
Read More »
PWM Dual Voltage AC Drives include isolated front end.
Series VFD05-D230-PCM features minimum speed adjustment potentiometer, DC injection braking, and automatic or manual restarts. Available to 1.5 hp, drives can be used with 3-phase induction, single-phase PSC, shaded-pole, and synchronous motors. Doubling jumper can be set to output 230 Vac when only 115 Vac power supply is available. With automatic restart, inverter will restart after low voltage...
Read More »
Volts/Hertz AC Drive features isolated front end.
Dual voltage Model VFP4X04-D230-PCM includes minimum speed adjustment potentiometer, DC injection braking, and automatic or manual restarts. It can control variety of motors including 3-phase induction, single-phase permanent split capacitor, shaded pole, and synchronous motors. Doubling jumper can be set to output 230 Vac when only 115 Vac power is available. Offered to 1 hp, drive comes in...
Read More »
DC to DC Drive suited for battery-operated vehicles.
Series DC500 PWM Drive includes runaway and rollaway protection, battery under-voltage control, and protection from overheating. Programmable safety parameters are set via any terminal program on Windows-based PC. Temperature sensor on heatsink triggers warning signal with field current boosting and armature cutbacks at 60Ã-
Read More »
Variable Speed DC Drive controls 90 Vdc motors.
Mounted on unanodized chassis, EC2 series SCR drive provides features for driving 90 Vdc brush motors up to 5 A with 115 Vac power supply. Start-stop control is available through inhibit terminals, and set-up is accomplished using on-board trimmer pots to adjust for min speed, max speed, IR compensation, current limit, and acceleration/deceleration. Applications include conveying, material...
Read More »
DC Drive offers 1% speed regulation.
M1 DC drive is mounted on gold chassis and measures only 4.30 x 2.64 in. It is rated for 5 A (1/2 hp) with 115 Vac input and 10 A (1 hp) with addition of optional heatsink. Programmable chip sets range for acceleration, deceleration, current limit, and IR compensation trimmer pots. Inhibit function and jumper can adjust factory set trimmer pot ranges to fit smaller motors. M1 will follow...
Read More »
Regenerative Drive offers dual voltage (115/230 Vac) input.
RG60U is available for 1/8 to 1 hp motors, or up to 2 hp with optional heatsink. It includes enable and inhibit terminals with option to invert functions. Invert jumpers allow user to decide if drive runs or stops when terminals are opened or closed. RG60U offers tacho-generator or armature feedback, 9 trimmer pots, cage clamp and screw terminal blocks for secure connections, and current limit...
Read More »