American Control Electronics
South Beloit, IL 61080
New CMC Series Compatible with Any DC Motor Controller
Provides adjustable current limit alarm for any DC motor controller, preventing false alarms due to predictable increases in current draw. Wired in series with a DC motor using a jumper to set a base current limit trip point. Available in three maximum trip current models of 5, 20, and 30 amps peak.
Read More »
New DCR300-60 and DCR600-60 Series Features Input voltage of 12/24 and 36/48 VDC Respectively
Controls are capable of braking or reversing on the fly, without use of braking resistors or motor lead swapping. Features output voltage of 0-12/0-24 VDC and 0-36/0-48 VDC respectively. Maximum current of 30 Amps and peak current of 60 Amps.
Read More »New DCL Series, a Low Voltage, Brushless Motor Control Operates in The 12-48 VDC Power Bandwidth, up to 30 Amps Peak (1 Minute) or 15 Amps Continuously
Removes many of the trim pots and jumpers associated with typical motor controls, reducing costs on hardware and setup. Include 1.37 form factor, 1% base speed regulation and 60:1 speed range. Base DCL units are Modbus capable and come with one trim pot for calibrating maximum speed and two DIP switches for closed / open loop operation.
Read More »
New PMB Series PWM Regenerative Drive Accepts Quadrature Encoder Feedback
Features isolated inputs that accept floating or grounded signals (0 ± 5 VDC, 0 ± 10 VDC or 4-20 mA). Meets UL 61800-5-1 standards and performs contactor-less reversing. Offered in NEMA 4X waterproof and dust-proof enclosure and comes with diagnostic LEDs for power and status indication.
Read More »
New PML Series DC Motor Drives Come with On-Board Trim Pots
The PML Series DC Motor Drives are available in steel and plastic NEMA 4X packages and can control motors ranging from 90 to 280 VDC, up to 5 A/1.5 HP. The trim-pots allow user to set maximum and minimum speeds, acceleration and deceleration rates, motoring and regening current limits and integral feedback gains. They come with isolated inputs that accept floating or grounded signals (0 ± 5 VDC,...
Read More »
Regenerative SCR Control supports OEM applications.
Intended for use with permanent magnet DC motors only, MGB Series features streamlined design with power in, power out, speed pot, direction switch, and stop/start switch. Microprocessor allows for custom programming where needed. Featuring 115/230 Vac input, 90/180 Vdc armature output, and 8 A armature current, series is engineered for OEM applications that require controlled deceleration,...
Read More »
New CMC Series Compatible with Any DC Motor Controller
Provides adjustable current limit alarm for any DC motor controller, preventing false alarms due to predictable increases in current draw. Wired in series with a DC motor using a jumper to set a base current limit trip point. Available in three maximum trip current models of 5, 20, and 30 amps peak.
Read More »
New DCR300-60 and DCR600-60 Series Features Input voltage of 12/24 and 36/48 VDC Respectively
Controls are capable of braking or reversing on the fly, without use of braking resistors or motor lead swapping. Features output voltage of 0-12/0-24 VDC and 0-36/0-48 VDC respectively. Maximum current of 30 Amps and peak current of 60 Amps.
Read More »New DCL Series, a Low Voltage, Brushless Motor Control Operates in The 12-48 VDC Power Bandwidth, up to 30 Amps Peak (1 Minute) or 15 Amps Continuously
Removes many of the trim pots and jumpers associated with typical motor controls, reducing costs on hardware and setup. Include 1.37 form factor, 1% base speed regulation and 60:1 speed range. Base DCL units are Modbus capable and come with one trim pot for calibrating maximum speed and two DIP switches for closed / open loop operation.
Read More »
New PMB Series PWM Regenerative Drive Accepts Quadrature Encoder Feedback
Features isolated inputs that accept floating or grounded signals (0 ± 5 VDC, 0 ± 10 VDC or 4-20 mA). Meets UL 61800-5-1 standards and performs contactor-less reversing. Offered in NEMA 4X waterproof and dust-proof enclosure and comes with diagnostic LEDs for power and status indication.
Read More »
New PML Series DC Motor Drives Come with On-Board Trim Pots
The PML Series DC Motor Drives are available in steel and plastic NEMA 4X packages and can control motors ranging from 90 to 280 VDC, up to 5 A/1.5 HP. The trim-pots allow user to set maximum and minimum speeds, acceleration and deceleration rates, motoring and regening current limits and integral feedback gains. They come with isolated inputs that accept floating or grounded signals (0 ± 5 VDC,...
Read More »
Regenerative SCR Control supports OEM applications.
Intended for use with permanent magnet DC motors only, MGB Series features streamlined design with power in, power out, speed pot, direction switch, and stop/start switch. Microprocessor allows for custom programming where needed. Featuring 115/230 Vac input, 90/180 Vdc armature output, and 8 A armature current, series is engineered for OEM applications that require controlled deceleration,...
Read More »