Phoenix Contact
Middletown, PA 17057
Switch expands Ethernet network on factory floor.
Stand-alone, unmanaged Ethernet/Fast Ethernet FL Switch 5 TX permits connection of up to 5 twisted-pair Ethernet segments, supports 10 Mbs and 100 Mbs transmission rates through autonegotiation, and fully supports either 1:1 or cross-over Ethernet cabling. Alarm output can be used to externally monitor redundant power source. Switch is DIN-rail mountable, and fits in industrialized ME housing.
Read More »
Circuit Breaker protects terminal blocks.
TCP Thermal Automatic Circuit Breaker provides overload protection in pluggable package for electrical installations and devices. Integrated switching function allows tripped circuits to be immediately switched back on. Modular base terminal block and pluggable circuit breaker implement power distribution tasks ranging from 0.25 to 10 A at 250 Vac or 65 Vdc. Variable length screw bridge can...
Read More »
D-Sub Connnectors plug into Profibus.
SUBCON-PLUS field-wire connectors make wiring and installation of Profibus nodes easy by providing a way to make terminations without soldering or crimping. Incoming and outgoing bus lines connect to screw or spring clamp terminal blocks. Connectors have EMI/RFI shielded housing, making it suitable for use on cables with up to 12 Mbit/s data rates. Available with angled or straight cable feeds....
Read More »
Distribution Blocks come with spring cage terminals.
FLKM-PVB power distribution modules are available in 16, 24, 32, and 48 positions, all with spring cage terminals. Each module is equipped with two potential connections: P1 and P2. Each supply terminal is capable of accepting up to 10-gauge conductor, and each distribution terminal is capable of accepting up to a 12-gauge conductor. There are no external bridging connections to be made on this...
Read More »Ethernet Switch connects five segments.
Stand alone FL Switch 5 TX Ethernet/Fast Ethernet unmanaged switch permits connection of up to five twisted pair Ethernet segments, supports both 10 Mbs and 100 Mbs transmission rates through autonegotiation, and supports either 1:1 or cross-over Ethernet cabling. Its alarm output can be used to externally monitor redundant power source. DIN-rail mountable module has industrialized housing.
Read More »
Fieldbus Coupler fits CANopen systems.
IL CAN BK bus coupler operates at any position in CANopen network. It uses diagnostics element to send detailed failure cause and location data to master, where they can be evaluated by appropriate software. Diagnostics and status displays enable exact module fault location and on-site determination of cause. Coupler supports analog and digital I/O, special function I/O, Category 4 Safety relay...
Read More »
Interface Boards connect to Galil motion controls.
VARIOFACE interconnect for Galil OPTIMA and ECONO series digital motion controllers can be used directly with Galil's 100, 80, and 36-pin cables. The 100-pin version comes with additional amplifier driver circuit and discrete screw connection to all conductors of Galil cable. Specific marking of each connection allows for quick, space-saving installation. Module is available as DIN-Rail or...
Read More »
Surge Suppressor handles three phase power.
BRICKTRAB modular DIN-rail mountable transient voltage surge suppressor provides power installations with more than 40,000 A of surge current handling capacity and low voltage protection levels. It protects against normal mode (line-to-line) and common mode (line-to-ground) transients, and has diagnostic monitoring of protection status with local and remote failure indication. Meets UL 1449 2nd...
Read More »
Wireless I/O handles analog and digital signals.
MCR-RAD integrated radio and I/O module eliminates cable and conduit for analog and digital signals in harsh industrial environments. Modules are available as transmitter/receiver pair and come factory programmed, calibrated, and tested as set, capable of carrying one 4 to 20 mA current loop and two digital status signals. Typical in-plant range is 600 to 1,000 ft, farther in outdoor...
Read More »
Analog Splitter divides transmitter signal.
MCR splitter takes signal from transmitter and sends two identical or different signals to receiving devices for monitoring, recording, or control. Input and two output ranges can be selected via DIP switches. Selectable analog signal ranges include 4 to 20 mA, 0 to 20 mA, 0 to l0 mA, 0 to l0 V, 0 to 5 V and 1 to 5 V. All analog range options are pre-configured and stored, eliminating need for...
Read More »