PennEngineering
Danboro, PA 18916
Spring-Loaded Plunger Assemblies serve as positioning pins.
Designed to install permanently in aluminum or steel sheets as thin as .060 in.- with hardness of HRB 80 or less, PEM® Type PTL2™ Assemblies serve as positioning pins to quickly move racks, slides, access panels, consoles, and similar equipment without requiring tools. Lockout feature keeps fastener's spring-loaded plunger fully retracted until plunger pin drops into final position....
Read More »Spring-Loaded Plunger Assemblies serve as positioning pins.
Designed to install permanently in aluminum or steel sheets as thin as .060 in.Ã- with hardness of HRB 80 or less, PEMî Type PTL2™ Assemblies serve as positioning pins to quickly move racks, slides, access panels, consoles, and similar equipment without requiring tools. Lockout feature keeps fastener's spring-loaded plunger fully retracted until plunger pin drops into final position....
Read More »
Electronics Assembly Pins provide alternative to screws.
Used to securely attach top panels to base panel or chassis in compact electronic assemblies via press-in action, microPEM-® TackSert™ pins provide alternatives to micro screws and eliminate issues associated with threaded hardware. Diagonal knurl holds top panel of any material and as thin as .008 in. to base panel or chassis manufactured from magnesium die-cast materials or plastics....
Read More »
Electronics Assembly Pins provide alternative to screws.
Used to securely attach top panels to base panel or chassis in compact electronic assemblies via press-in action, microPEMÃ-® TackSert™ pins provide alternatives to micro screwsÃÂ and eliminate issues associated with threaded hardware. Diagonal knurl holds top panel of any material and as thin as .008 in. toÃÂ base panel or chassis manufactured from magnesium die-cast materials or...
Read More »
Fastener-Installation Press includes optical safety sensor.
Designed for installing self-clinching fasteners, PEMSERTER-® Series 4® integrates Optical Sensor Indicator to signal when safety is properly set for each job. OSI activates during set-up mode when press ram/punch is being adjusted onto workpiece prior to fastener installation. OSI changes from black to orange at exact point when safety is successfully engaged, eliminating potential for...
Read More »
Fastener-Installation Press includes optical safety sensor.
Designed for installing self-clinching fasteners, PEMSERTERÃ-® Series 4î integrates Optical Sensor Indicator to signal when safety is properly set for each job. OSI activates during set-up mode when press ram/punch is being adjusted onto workpiece prior to fastener installation. OSI changes from black to orange at exact point when safety is successfully engaged, eliminating potential...
Read More »
Self-Clinching Flush Nuts install into stainless steel sheets.
Manufactured from 400 Series stainless steel, PEMSERT-® Type F4™ Self-Clinching Flush Nuts provide load-bearing threads in 300 Series stainless steel without creating protrusions on either side. Upon permanent installation into sheets as thin as .060 in., both top and bottom of sheet will remain flat. Nuts are available in thread sizes #2-56 through ¼-20 / M2 through M6 and can perform...
Read More »
Self-Clinching Flush Nuts install into stainless steel sheets.
Manufactured from 400 Series stainless steel, PEMSERTÃ-® Type F4™ Self-Clinching Flush Nuts provide load-bearing threads in 300 Series stainless steel without creating protrusions on either side. Upon permanent installation into sheets as thin as .060 in., both top and bottom of sheet will remain flat. Nuts are availableàin thread sizes #2-56 through ü-20 / M2 through M6 and...
Read More »Self-Clinching Standoffs suit thin stainless steel assemblies.
Manufactured from heat-treated 400 Series stainless steel, PEM-® Type TSO4™ standoffs are used for stacking or spacing components to or from ultra-thin stainless steel panels as thin as .025 in. and with max hardness of HRB 88 on Rockwell B scale or HB 183 on Brinell scale. Hardened stainless fasteners install permanently; one mating screw is required for final component attachment. Various...
Read More »Self-Clinching Standoffs suit thin stainless steel assemblies.
Manufactured from heat-treated 400 Series stainless steel, PEMÃ-® Type TSO4™ standoffs are used for stacking or spacing components to or from ultra-thin stainless steel panels as thin as .025 in. and with max hardness of HRB 88 on Rockwell B scale or HB 183 on Brinell scale.ÃÂ Hardened stainless fasteners install permanently; one mating screw is required for final component attachment....
Read More »