Mi-T-M
Peosta, IA 52068
Stationary Air Compressors offer 30 gal capacity.
Single-stage model incorporates 3 hp, 230 V electric motor and 10 in. flywheel. Two-stage model offers either 5.0 hp, 208-230 V electric motor or 8.0-11.0 hp gasoline engine, both with 15.7 in. flywheel. Other features include 14 gauge 2-piece belt guard, SS braided discharge hose, pneumatic idle control, and auto start/stop with optional continuous run, manual drain valves, and 7 gauge baseplate...
Read More »Hot Water Pressure Washers feature LP-fueled heat exchanger.
Series HLP includes 120 V, single phase, open drip-proof electric motor; LP-gas fired natural draft with aspirating type burner; gas regulator; LP-gas shut-off valve; and belt-driven, triplex crankshaft pump. Powder-coated cabinet-style steel frame includes 4 pneumatic tires and tank carrier with band for 30 lb propane tanks. Additional features include 50 ft steel wire braided pressure hose and...
Read More »Pressure Washers feature 1.5-8.0 hp TEFC electric motors.
Job Pro Electric Series cold water pressure washers are equipped with direct-drive triplex piston pumps with ceramic plungers, 35 ft power cord, forged brass manifold, 1 in. powder-coated steel handles, and 3/16 in. base plates. Suited for indoor industrial and agricultural applications, units include pneumatic tires with tubes and dual rubber isolators. Trigger gun features safety lock-off and...
Read More »Metal-Cutting Saw produces burr-free cuts.
Cool Cut(TM) Saw cuts mild steel up to 5/16 in. thick, aluminum up to 3/8 in. thick, and stainless steel up to Ã-¼ in. thick. Over 90% of chips and sparks are collected. Powered by 3,500 rpm and 15 A/1,200 W motor, it produces 2 in. deep cut. Features include 7 in. blade, chip collector, blade housing, aluminum base, guide handle with convenient guide edge, 45Ã-
Read More »Hot Water Pressure Washers have insulated trigger guns.
HS Series hot water skid pressure washers include industrial gasoline or diesel engines with electric start, belt drive triplex piston pump, and steel square tube frame. Equipped with Ã-½ in. schedule 80 coil with stainless steel wrap heat exchanger, products offer 80 mesh, stainless steel inlet water strainer; pressure relief valve; 2,500 W generator; 50 ft steel wire-braided pressure hose;...
Read More »
Pressure Washers offer quiet operation with less vibration.
Series HSE consists of belt and direct drive hot water pressure washers operating on TEFC electric motor with manual thermal overload protection. They are equipped with dual spiral coil with powder coated heat exchanger, No. 1 or No. 2 diesel or kerosene fired burner, and high pressure detergent injection and float tank. Steel tube frame is reinforced powder coated. Steel wire-braided pressure...
Read More »
Job-Site Boxes have swing-out handles for easier mobility.
To provide protection for tools and work gear, heavy-duty job site boxes incorporate solid steel construction with full arc-welded seams, powder-coat finish, and tamper-proof padlock protectors. Full length concealed hinges provide additional protection and strength, while reinforced support skids add protection and aid in transport. Available sizes are: 36 x 19 x 16 in., 48 x 22 x 22 in., 48 x...
Read More »Wet/Dry Vacuum has 9 gallon capacity.
Model MV-900-0MEV incorporates 25 ft electrical cord with cord wrap, poly construction, recessed polyolefin wheels, and 10 ft hose with inlet cuff. Offered with 1.3 hp, 2-stage bypass, 120 V, self-cooling, continuous motor, 9 A unit also includes 101 cfm, 6 gal water recovery and 87 in. waterlift. Also included: aluminum/plastic extension wand, curved plastic wand, 12 in. combination floor tool,...
Read More »Pressure Washer is cold-water, belt-drive type.
CW Series, for commercial and industrial users, is powered by 11.0, 13.0 and 16.0 hp Honda and Vanguard engines. Features include triplex ceramic plunger pump, thermal relief valve, water filter, 50 ft of hose, 36 in. steel powder-coated lance, quick-connect nozzles, pneumatic mag tires, powder-coated 1Ã-¼ in. steel tube handles, hose wrap with wand holder, and 2-piece belt guard.
Read More »
Electro-Coagulation System removes impurities from oils.
Typically used for pretreatment of emulsified oils, ECL Series has flow rate of 5 gallons per minute. It features 230V, single phase, 20 amp electrical motor with .75 hp pump and 175 gallon cone tank. It is also suitable for removal of suspended solids, removal of complex organics, and destruction and removal of bacteria, viruses, and cysts.
Read More »