Ogura Industrial Corp.
Somerset, NJ 08873
Pneumatic Caliper Disc Brakes resist vibration.
Spring-applied and pneumatically released, Models ANB-1100-CP and ANB-2300-CP provide 11,000 N and 23,000 N of clamping force, respectively. Actual torque applied to given application is function of diameter of disc, and disc for either brake would be supplied by customer. Any time pneumatic pressure is lost, brakes can come on and hold in emergency, making them suitable for wind turbines and...
Read More »
Double Brake Design improves commercial elevator safety.
Double MNB brake for commercial elevators consists of 2 identical brakes mounted on one adaptor flange. Since brakes are holding only, both operate simultaneously when required to come on. If problem occurs with one brake, other can still handle torque load required. Both brakes are equipped with limit switches to know when brake is either engaged or disengaged. Product helps meet demands in...
Read More »
Rotary Air Blowers target industrial and mobile applications.
Driven by electric motors that are directly coupled to blowers input shaft, TX Series includes models ranging from 400-2,800 cc/revolution. Wankel-based, positive displacement blowers offer pressure differentials up to 2.0 for short durations, with 1.8 running continuously. Efficiencies as high as 65-70% can be achieved, depending on model, pressure, and flow. Applications include industrial...
Read More »
High Speed Ogura Mico Clutch Now Available with Shaft
Ogura has enhanced their Hi-Mic5 design to include a shaft designed to a customer's specification. The electromagnetic clutch incorporates two ball bearing in the field assembly and two ball bearings in the pulley assembly. This means that not only can the clutch handle about a 40% higher speed/load than a bushing clutch it can also take a side load on the pulley so there's no problem when using...
Read More »
Electromagnetic Brake delivers 4.5 lb-in. torque.
Supplied standard with 24 V coil, Model MCB5 is capable of speeds of 3,600 rpm. Brake uses zero backlash spring armature so there is no rattle noise when brake is disengaged. Bore on hub/armature comes standard with keyway and 2 set screws. Small, lightweight brake is RoHS-compliant and suited for both industrial and automotive applications.
Read More »
High Cycle Clutch/Brake
MP units are made for every quick and precise cycling applications. Units include a low voltage clutch and a brake to start and stop a load. All units maintain a consistent air gap, even thought units wear, which controls engagement time.
Read More »
Electric Clutches Run Components from Gas Engines
These clutches are made to mount eight onto an engine shaft and take the vibration and temperature from small gas engines or diesel engines. Clutches can then either drive customer's components directly or through a belt. A variety of pulleys already exist, however, custom designs are also possible.
Read More »
Single Piece Clutch or Brake Available
To reduce assembly time of sub components for machinery manufacturers Ogura has developed bearing mounted clutch and brake assemblies that can be shipped as one piece, so no assembly or adjustment is required. Universal mount types come with a flange for a customer to mount their own sprocket or pulley, however if desired units can also be designed to come with a clutch output.
Read More »
Forced Air Cooling Doubles Heat Dissipation
January 25, 2008 Ogura's larger series of magnetic particle clutches and brakes (starting at 9lbs-ft up to 150 lbs-ft) are available with forced air cooling for increased heat dissipation. All units come standard with input and output connections so shop air can be easily used to help cool units to increase life and performance. Ogura products are manufactured in Europe, North and South America...
Read More »Electromagnetic Clutches include silent armature option.
Incorporating noise dampening plastic disk in both armature and rotor, V-Series Clutches are available in 4 modules from 3-43 lb-ft torque with either 4 or 90 V coils. Minimized noise version is designed to satisfy medical and other consumer related applications in which clutch or brake engagement noise would be objectionable.
Read More »
Pneumatic Caliper Disc Brakes resist vibration.
Spring-applied and pneumatically released, Models ANB-1100-CP and ANB-2300-CP provide 11,000 N and 23,000 N of clamping force, respectively. Actual torque applied to given application is function of diameter of disc, and disc for either brake would be supplied by customer. Any time pneumatic pressure is lost, brakes can come on and hold in emergency, making them suitable for wind turbines and...
Read More »
Double Brake Design improves commercial elevator safety.
Double MNB brake for commercial elevators consists of 2 identical brakes mounted on one adaptor flange. Since brakes are holding only, both operate simultaneously when required to come on. If problem occurs with one brake, other can still handle torque load required. Both brakes are equipped with limit switches to know when brake is either engaged or disengaged. Product helps meet demands in...
Read More »
Rotary Air Blowers target industrial and mobile applications.
Driven by electric motors that are directly coupled to blowers input shaft, TX Series includes models ranging from 400-2,800 cc/revolution. Wankel-based, positive displacement blowers offer pressure differentials up to 2.0 for short durations, with 1.8 running continuously. Efficiencies as high as 65-70% can be achieved, depending on model, pressure, and flow. Applications include industrial...
Read More »
High Speed Ogura Mico Clutch Now Available with Shaft
Ogura has enhanced their Hi-Mic5 design to include a shaft designed to a customer's specification. The electromagnetic clutch incorporates two ball bearing in the field assembly and two ball bearings in the pulley assembly. This means that not only can the clutch handle about a 40% higher speed/load than a bushing clutch it can also take a side load on the pulley so there's no problem when using...
Read More »
Electromagnetic Brake delivers 4.5 lb-in. torque.
Supplied standard with 24 V coil, Model MCB5 is capable of speeds of 3,600 rpm. Brake uses zero backlash spring armature so there is no rattle noise when brake is disengaged. Bore on hub/armature comes standard with keyway and 2 set screws. Small, lightweight brake is RoHS-compliant and suited for both industrial and automotive applications.
Read More »
High Cycle Clutch/Brake
MP units are made for every quick and precise cycling applications. Units include a low voltage clutch and a brake to start and stop a load. All units maintain a consistent air gap, even thought units wear, which controls engagement time.
Read More »
Electric Clutches Run Components from Gas Engines
These clutches are made to mount eight onto an engine shaft and take the vibration and temperature from small gas engines or diesel engines. Clutches can then either drive customer's components directly or through a belt. A variety of pulleys already exist, however, custom designs are also possible.
Read More »
Single Piece Clutch or Brake Available
To reduce assembly time of sub components for machinery manufacturers Ogura has developed bearing mounted clutch and brake assemblies that can be shipped as one piece, so no assembly or adjustment is required. Universal mount types come with a flange for a customer to mount their own sprocket or pulley, however if desired units can also be designed to come with a clutch output.
Read More »New Industrial Electric Clutch/Brake Catalog from Ogura
Ogura Industrial Corporation has just introduced their new Industrial Electromagnetic Clutch and Brake catalogue. The 137 page catalog shows 340 different models of electromagnetic, single face, multiple disk, tooth, foot mounted, hysteresis and magnetic particle clutches and brakes and power off brakes. The new catalog shows new series of power off brakes as well as some changes to the other...
Read More »
Forced Air Cooling Doubles Heat Dissipation
January 25, 2008 Ogura's larger series of magnetic particle clutches and brakes (starting at 9lbs-ft up to 150 lbs-ft) are available with forced air cooling for increased heat dissipation. All units come standard with input and output connections so shop air can be easily used to help cool units to increase life and performance. Ogura products are manufactured in Europe, North and South America...
Read More »