Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Bending System handles high/low production runs.
Usable for batch runs as small as 30 units, BendMaster handles components up to 88 lb. Product is controlled via single control system and is programmed using ToPs 600. Automation extension module can be used to program bending cell. Part geometries are defined once or can be taken over from ToPs programs. Bending process and part handling are generated automatically, and simulation allows...
Read More »Wide-Mouth Balers offer 4 different hopper dimensions.
Series 42H and 43H, suited for continuous use in high-volume operations, include Pathfinder Plus color touch screen, automatic tensioning controls, and 5-tie auto-tier that swings away from baling unit for access to components. Three-stage replaceable shear blade eliminates need for pre-shredding. Feed openings range from 41 x 50 in. to 41 x 80 in. Compression forces up to 339,000 lb produce...
Read More »Ceiling Mount offers projector security.
Armor Lock-BoxÃ-® offers theft-resistant Armor Lock security at extension column, key-lock, and additional lockdown point for padlock. Ball and socket design provides multi-directional adjustments for roll, pitch, and yaw. Box attaches to 1Ã-½ in. diameter extension column or Ã-½ in. threaded rod. Available in small and medium sizes to accommodate various size projectors, mount is...
Read More »Actuator Assemblies have TFE coating.
Lead screw, linear rail, spline shaft, and ScrewRail(TM) actuator assemblies are available with Kerkote(TM) TFE coating, which reduces friction and extends life of maintenance-free assemblies. Coating decreases erratic drag torques and unpredictable wear and provides maximum level of self-lubrication. Dry lubricant will not become paste-like and attract dirt or debris. Assemblies are suited for...
Read More »Air Blast Cleaning System extends maintenance intervals.
Auto Air Blast System blows jet stream of air for 1-3 min over dissolved oxygen sensor membrane at set intervals. Programmable timer in analyzer controls cleaning frequency, and compressor located near sensor provides air supply. Model 499ADO membrane dissolved oxygen sensor features molded Noryl construction and is suited for flow-through or submersion mounting. It incorporates integral...
Read More »Poppet Valves offer flow rates up to 40 Cv.
ProspectorÃ-® Poppet Valves, available in solenoid and pilot actuated formats, feature operating pressure to 290 psi with pilot air supply pressure ranging from 14-290 psi bar. Operating temperature is -84 to +129Ã-
Read More »Servo Motors suit food and beverage industry.
Food-grade MP Series Motors offer continuous stall torque of 14-176 lb-in. and include shaft seal with hardened wear sleeve. They are IP66- and IP67-rated with stainless steel motor shaft and fasteners providing corrosion resistance and protection against liquid contamination. IP67-rated connectors can be rotated 180Ã-
Read More »Press Automation System offers signature analysis.
Co-Pilot integrated press automation and monitoring system provides die protection, tonnage monitoring with reverse load, programmable limit switches, and brake monitoring in one resolver-based package. All functions have alarms if settings are violated. Features include debounce, motion detect, counters, job storage, speed compensation, 3 password levels, serial ports, and flash card for job...
Read More »Industrial Ethernet Switch is configurable through serial port.
CTRLinkÃ-® EISC16-100T has 16 10/100 Mbps twisted-pair ports, one RJ-45 connector, and programmable fault relay that interfaces to annunciator devices or acts as input to controller. In addition to auto-negotiation of data rate, duplex, and flow control, these settings can be manually configured for each port. EIA-232 serial port is used for configuration of unit. Parameters can be saved and...
Read More »Multi-Parting Line Systems target plastics processors.
Multi-Parting Line (MPL) Systems double cavitation of standard single-face molds. They can be configured as turnkey systems with mold bases, hot runner systems, temperature controllers, and centering devices. Stack Mold Components enable system customization. Dual Mold Carrier enables MPL molding utilizing existing single-face molds. Tandem Molding employs 2 mold faces with staggered processes,...
Read More »