Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Wheeled Battery Charger offers multiple charging rates.
In addition to providing 200 A of engine starting assistance to boost disabled 12 V vehicle batteries, Model No. 4725 delivers 40, 20, and 5 A charge rates in 12 V mode and 40 A charge rate in 6 V mode. Ammeter lets operator monitor charging progress, and full size clamps can penetrate corroded battery terminals. Wheel size and handle design ease mobility, and overall design provices...
Read More »Non-Contact Resolvers suit defense and space applications.
Providing non-contact rotary and angle position sensing, Hawk(TM) 1-Inch Series delivers -
Read More »Omnipolar Digital Hall-Effect Sensor has micropower architecture.
Supplied in SOT-23 subminiature package, SL353 Series features supply voltage as low as 2.2 Vdc and average current as low as to 1.8 -µA typ. Product is available in 2 duty cycle configurations: SL353HT has 13% duty cycle typ and low current drain of 0.33 mA, and is suited for energy-efficient products requiring higher switching frequencies. SL353LT has very low duty cycle (0.013% typ.) and...
Read More »
Telescopic Handler provides max life height of 19 ft, 3 in.
With overall height of 6 ft, 7 in. and width of just under 6 ft, Model MLT 625 telescopic handler can access small storage buildings, greenhouses, and stables. Handler provides short turning radius of 10 ft and max lift capacity of 5,500 lb. Turbo-charged 75 hp Kubota diesel engine coupled with hydraulic gear pump results in flow rate of 24 gpm at 3,408 psi. Additional features include 2-speed...
Read More »
Two-Wire CO Gas Sensor supports non-intrusive calibration.
Featuring 4-20 mA, 2-wire, loop-powered design, 4501-04 eliminates need for separate power runs and associated power distribution and circuit protection for each device. Operator interface with integral, scrolling, menu-driven LCD facilitates access to gas status, calibration instructions, adjustment of ranges and outputs, as well as diagnostic information. Along with 180 day calibration...
Read More »
Modular Pneumatic Valve Interlock supports flexible application.
Suitable for isolation of pneumatic power source, Pneumatic Valve+ (PV+) unit has modular design that allows configuration of array of valves, trapped key interlocks, and key switches in any combination. Constructed with zinc alloy valve body and mild steel, zinc-coated plates, design enables unit to be used in conjunction with other functional modules. Combination of isolation/access keys is...
Read More »
Surge Suppressors feature widely spaced outlets.
Suited for home and office electronics such as computers, workstations, and point-of-sale terminals, Protect It! TLP64 and TLP66NET deliver up to 1,080 joules of surge protection. Units feature 6 outlets with integrated child safety covers, EMI/RFI noise filtering, Tel/Ethernet protection options, and diagnostic LEDs that confirm surge protection status. With widely spaced outlets, surge...
Read More »Cold Plates suit demanding military cooling applications.
Designed to meet VME64x/VPX standards, Cold Plates are available in 3U, 6U, and 9U formats. Baseline aluminum cold plates are produced from aluminum alloys such as 6061 and 6063 with thermal conductivity values of 166 and 201 W/m. k-Core-® models, encapsulating Annealed Pyrolytic Graphite with same aluminum alloys as basic models, deliver up to 6x conductance. Embedded Heat Pipe options are...
Read More »Speed-Controlled Heating Circulator uses ECM technology.
Featuring spherical motor design, ecocirc-® pump uses ECM (Electronically Commutated Motor) technology to conserve energy while delivering hot water throughout commercial or residential properties. Control modes include auto for automatic proportional pressure control and vario for stepless speed control with constant curve. As sole moving part, rotor/impeller magnetically balanced on stationery...
Read More »
Round-Bowl Dryers use dry maize for moisture absorption.
Available with tub capacities of 3, 5, 10, and 15 ft-³, OR-CD Series is suited for drying machined parts after washing and for removing surface oil and grease. Parts can be fed into machine individually or in batches, for once-around-and-out drying before next production step. Driven by 15 hp, 1,800 rpm totally enclosed motor, systems feature vertical-shaft vibrator that can be reached for...
Read More »