Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
CO2 Laser suits plastics and organics processing.
Santa Clara, Calif., June 15, 2009 - A new CO2 laser from Coherent, Inc. (Santa Clara, CA) (Nasdaq: COHR) offers greater reliability and reduced cost of ownership for applications involving processing of textiles, organic materials, plastics and even thin metals. The DIAMOND(TM) E-150 is a slab discharge CO2 laser that delivers 150W (at 1 kHz repetition rate) at a wavelength of 10.6 µm, while...
Read More »
CompactPCI DC/DC Converter converts +28 Vdc to quad outputs.
High Power-Density, Low Profile Unit Converts +28 Vdc to Quad Outputs Bohemia NY -- North Atlantic Industries (NAI) has announced the availability of its latest, next generation 3U, cPCI DC/DC converter. The 55MQ2 provides 150 Watts of output power (+5Vdc, +3.3Vdc and ±12Vdc) at full load over its operating temperature range of -55°C to +85°C (conduction cooled and measured at card edge). This...
Read More »Green Laser delivers 5 W at 532 nm.
Powered by AAA(TM) diodes, Verdi(TM) G5 is based on optically pumped semiconductor laser technology. Unit features low noise of less than 0.03% rms and single-spatial mode output with M-² less than 1.1. Built on PermAlign(TM) solder-down manufacturing platform, Verdi G5 provides reliability of more than 20,000 hours and is suited for pumping ultrafast and CW Titanium:Sapphire lasers.
Read More »Commercial Deodorizer/Cleaner is non-toxic and effective.
Derived 100% from plants/vegetables without any ozone-depleting substances, synthetics, or VOCs, Eco-Green-® Deodorizer and Cleaner removes organic matter and hydrocarbon residues in industrial settings at their source to eliminate pungent, lingering smells. Environmentally safe solution, certified as Readily Biodegradable, employs Micro-Blasting® technology and can be used with cold/hot...
Read More »
Laser Module exhibits low phase noise.
Martinsried, 07-14-2009 - Redfern Integrated Optics, Inc. (RIO), leading supplier of low noise external cavity lasers and subsystems for fiber optic sensing, LIDAR, reflectometry, RF photonics and other applications, announced several new features becoming available for its ORION module platform. Based on the unprecedented success of the recently introduced ORION module at Photonics West '09, the...
Read More »Excimer Laser minimizes cost/Watt for UV micromachining.
With optimized Novatube-® construction and discharge design, LEAP laser is designed for micromachining applications in microelectronics and medical device manufacturing. Direct UV laser emission delivers per pulse energy of 650 mJ at repetition rates to 200 Hz, resulting in 130 W average power, at wavelengths of 248 or 308 nm. Primary use is intended for micro-manufacturing of small devices with...
Read More »
Fiber Optic Cleaner features antistatic properties.
Available in 1.25 and 2.5 mm versions, pen type Neoclean-E cleans end-faces of fiber connectors and in-adapter ferrules. Microfiber tissue removes all contaminants and secures them, while antistatic property prevents static load that could bring new contamination after cleaning. Equipped with replaceable cartridge, Neoclean-E can be reused, avoiding disposal of tool when thread is due to be...
Read More »Green Laser supports high-throughput micromachining.
Santa Clara, Calif., June 15, 2009 - The new MATRIX(TM) 532-8-100 is a Q-switched, diode pumped, solid state laser designed to deliver the best cost to performance ratio for demanding micromachining tasks in solar, semiconductor and medical device manufacturing. Specifically, it provides 8W of output power at 532 nm at a pulse rate of 100 kHz, in order to support high-throughput applications....
Read More »Green Lasers suit life science applications.
Exhibiting noise of less than 0.1% rms and mode quality of M2 less than 1.1, Genesis(TM) CW green (532 nm) lasers are air-cooled and can be directly modulated. Genesis 532-1000 S lasers produce over 1 W of output power, while Genesis 532-500 S lasers deliver over 0.5 W. Both are based on optically pumped semiconductor laser (OPSL) technology, which is scalable in wavelength and output power.
Read More »
High-Power Fiber Lasers output up to 750 or 1,000 W.
FL Series can be used to weld small parts with low thermal distortion and minimal heat affected zones. Beam quality can be coupled with fiber optics 50-600 -µm in diameter, equivalent to beam quality of 2.5-30 mm x mrad. Additionally, model FL 010 S offers option of fiber laser solution with single mode beam quality of 0.4 mm x mrad (typ) and 1,000 W output power. Optional beam switch and energy...
Read More »