Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Integrated Load Switch features low ON resistance.
Providing typical ON resistance of 5.7 mW at 3.6 V, Model TPS22924C comes in 1.4 x 0.9 mm chip scale package, addressing space-constrained, battery-powered applications. Unit features input voltage range of 0.75-3.6 V, maximum continuous switch current of 2 A, and shutdown current of less than 2 -µA. Applications include media players, point-of-sale terminals, GPS systems, netbooks/notebooks,...
Read More »
18-Pin MCUs operate on 1.8-5.5 V.
Models PIC16(L)F1826 and PIC16(L)F1827 general-purpose 8-bit MCUs include mid-range core as well as mTouch(TM) capacitive touch-sensing module and dual I2C(TM)/SPI interface. Digital signal modulator enables designers to customize communication interfaces. With 14 instructions for simplified C programming, units feature internal oscillator up to 32 MHz, flash program memory up to 7 KB, data...
Read More »TFT/OLED Display Driver Board adds GUI to embedded systems.
Measuring 1.5 x 3.0 in., GEMexpress(TM) is integrated 6-layer PCBA that can interface to any display and is comprised of GEM Graphical OS Chip(TM) for color displays and those parts required to support this chip. Chip includes LCD controller, touch panel decoder, ARM7 processor, and Graphical Operating System in Silicon(TM). In addition to 32 Mb serial flash and 64 Mb SDRAM, features include 4-...
Read More »SMD Antenna targets global LTE mobile device applications.
Capable of supporting 10 wireless protocols, Agilis A10346 Switchable Magnetic Dipole Antenna provides global dual-mode GSM/LTE capability plus Wi-Fi-®, Bluetooth®, and WiMAX(TM) in single structure. Single capacitive feed antenna is implemented with 3-pin diode switch that enables operation in 3 sets of frequency bands. Unit is suited for embedded cellular and mobile broadband applications...
Read More »
CAM Software runs seamlessly in SolidWorks.
With Mastercam-® X4 for SolidWorks®, users can program parts directly within SolidWorks using Mastercam's toolpaths and machining strategies. Software offers full suite of cutting strategies, including Feature Based Machining and 3D High Speed Machining toolpaths. Dynamic Milling creates constantly adapting toolpath that delivers consistent cutting conditions and allows use of entire flute...
Read More »Integrated Load Switch features low ON resistance.
Providing typical ON resistance of 5.7 mW at 3.6 V, Model TPS22924C comes in 1.4 x 0.9 mm chip scale package, addressing space-constrained, battery-powered applications. Unit features input voltage range of 0.75-3.6 V, maximum continuous switch current of 2 A, and shutdown current of less than 2 Ã-µA. Applications include media players, point-of-sale terminals, GPS systems,...
Read More »
18-Pin MCUs operate on 1.8-5.5 V.
Models PIC16(L)F1826 and PIC16(L)F1827 general-purpose 8-bit MCUs include mid-range core as well as mTouch(TM) capacitive touch-sensing module and dual I2C(TM)/SPI interface. Digital signal modulator enables designers to customize communication interfaces. With 14 instructions for simplified C programming, units feature internal oscillator up to 32 MHz, flash program memory up to 7 KB, data...
Read More »TFT/OLED Display Driver Board adds GUI to embedded systems.
Measuring 1.5 x 3.0 in., GEMexpress(TM) is integrated 6-layer PCBA that can interface to any display and is comprised of GEM Graphical OS Chip(TM) for color displays and those parts required to support this chip. Chip includes LCD controller, touch panel decoder, ARM7 processor, and Graphical Operating System in Silicon(TM). In addition to 32 Mb serial flash and 64 Mb SDRAM, features include 4-...
Read More »SMD Antenna targets global LTE mobile device applications.
Capable of supporting 10 wireless protocols, Agilis A10346 Switchable Magnetic Dipole Antenna provides global dual-mode GSM/LTE capability plus Wi-FiÃ-®, Bluetoothî, and WiMAX(TM) in single structure. Single capacitive feed antenna is implemented with 3-pin diode switch that enables operation in 3 sets of frequency bands. Unit is suited for embedded cellular and mobile broadband...
Read More »
CAM Software runs seamlessly in SolidWorks.
With MastercamÃ-® X4 for SolidWorksî, users can program parts directly within SolidWorks using Mastercam's toolpaths and machining strategies. Software offers full suite of cutting strategies, including Feature Based Machining and 3D High Speed Machining toolpaths. Dynamic Milling creates constantly adapting toolpath that delivers consistent cutting conditions and allows use of entire...
Read More »