Aprima Medical Software, Inc
Carrollton, TX 75006
Share:

Rugged Ethernet Switches come in managed/unmanaged models.
Supporting either 4- or 8-pin M12 twisted pair cable and 4- and 5-pin 7/8-16UN power cable, fully encapsulated switches are capable of information transfer and real-time I/O control in harsh environments. Offered in managed and unmanaged options, 4-pin switch suits EtherNet/IP(TM) applications, while 8-pin switch targets standard Ethernet applications. Unmanaged switch comes with 5 or 9 ports,...
Read More »
High Torque Stepping Motors have high efficiency design.
PKE series 2-phase motors have 1.65 in. square frame size and come in 3 stack lengths of 1.3 (PKE243x), 1.54 (PKE244x), and 1.85 (PKE245x) in. Output torque ranges from 34 oz-in. for PKE243A-L unipolar model up to 77.8 oz-in. for PKE245DA-L bipolar model. Offered with standard or double shafts, motors achieve shaft speeds of more than 2,000 rpm with 24 Vdc driver. Low heat generation enables...
Read More »
Miniature Charge Amplifiers are used with piezoelectric transducers.
Housed in aluminum case measuring 1.575 x 1 x 1 in. and weighing 50 g, Series 5820 charge amplifiers are suited for use with all piezoelectric transducers to form various airborne vibration and shock data acquisition systems. Units are available in 7 standard charge conversion ranges, each offering a 10.1 tandem gain adjustment capability. Models provide dual signal outputs, one biased around...
Read More »
Rugged Ethernet Switches come in managed/unmanaged models.
Supporting either 4- or 8-pin M12 twisted pair cable and 4- and 5-pin 7/8-16UN power cable, fully encapsulated switches are capable of information transfer and real-time I/O control in harsh environments. Offered in managed and unmanaged options, 4-pin switch suits EtherNet/IP(TM) applications, while 8-pin switch targets standard Ethernet applications. Unmanaged switch comes with 5 or 9 ports,...
Read More »
High Torque Stepping Motors have high efficiency design.
PKE series 2-phase motors have 1.65 in. square frame size and come in 3 stack lengths of 1.3 (PKE243x), 1.54 (PKE244x), and 1.85 (PKE245x) in. Output torque ranges from 34 oz-in. for PKE243A-L unipolar model up to 77.8 oz-in. for PKE245DA-L bipolar model. Offered with standard or double shafts, motors achieve shaft speeds of more than 2,000 rpm with 24 Vdc driver. Low heat generation enables...
Read More »Parallel Gripper operates in dirty environments.
Available in sizes 240 and 300, 2-Finger-Parallel Gripper DPG-plus offers actuation via oval piston and multitooth guidance for precision and fail-safe handling. It is IP67-rated and no material can get inside device from work environment. Mounting pattern is identical to PGN-plus and PGB grippers, allowing for interchangeability. It is suited for loading/unloading grinding, turning, and milling...
Read More »
Presetting Tool is made from carbon steel.
Available in sizes of 5/8 in. and up, presetting tool is used to preset ferrules on tubing prior to final assembly into fitting. It is suited for instrumentation tube fitting installations in tight spaces or hard-to-work areas.
Read More »
Xenon Photoflash Charger ICs come in 2 x 2 mm DFN package.
Offering charge and trigger voltage logic thresholds set at 1 VHI, models A8732 and A8735 support applications implementing low-voltage control logic, such as mobile phones. Current limit for A8732 can be programmed from 0.45-1.5 in 16 steps with single wire interface, while for A8735 it is fixed at 1 A. Utilizing primary-side voltage sensing, devices eliminate need for secondary-side voltage...
Read More »Parallel Gripper operates in dirty environments.
Available in sizes 240 and 300, 2-Finger-Parallel Gripper DPG-plus offers actuation via oval piston and multitooth guidance for precision and fail-safe handling. It is IP67-rated and no material can get inside device from work environment. Mounting pattern is identical to PGN-plus and PGB grippers, allowing for interchangeability. It is suited for loading/unloading grinding, turning, and milling...
Read More »
Presetting Tool is made from carbon steel.
Available in sizes of 5/8 in. and up, presetting tool is used to preset ferrules on tubing prior to final assembly into fitting. It is suited for instrumentation tube fitting installations in tight spaces or hard-to-work areas.
Read More »