Aprima Medical Software, Inc

Transmitters are available in 14 units.
Electrical Equipment & Systems

Transmitters are available in 14 units.

LPI-SERIES isolated loop powered transmitters feature field programmable bi-polar input ranges with 2 kV isolation and accuracy of 0.10%. Members include: DC to DC with fixed or programmable input range, Bridge to DC, Resistance to DC, Potentiometer to DC, Differential RTD to DC, RTD to DC with fixed or programmable ranges, Thermocouple to DC with fixed or programmable ranges, AC to DC with...

Read More »
Cal-Gas Standards Generator calibrates gas analyzers.
Test & Measurement

Cal-Gas Standards Generator calibrates gas analyzers.

Model 491MB Gas Standards Generator is designed to calibrate gas analyzers such as gas chromatographs, mass spectrometers, and ion mobility spectrometers. 491MB uses Trace Source(TM) Permeation Tubes to generate low concentrations (1000 ppm to ppb) gas standards for VOCs, Acid Gases, Amines, Sulfurs, and Hydrocarbons (400+ compounds). Standards are traceable to NIST.

Read More »
Sensors measure micro liquid flow rates.
Sensors, Monitors & Transducers

Sensors measure micro liquid flow rates.

Rated for operation up to 500 psig, Series 102 liquid flow sensors measure flow rates from 13 mL/min to 10 L/min (2.6 GPM) with ± 3% full scale accuracy and ±0.2% repeatability. Sensors provide linear 0-5 VDC output signal and have turndown ratio up to 10:1. Series 102T has dual output signals consisting of 0-5 VDC linear and buffered 7.5 V pulse output proportional to flow rate.

Read More »
Precision Ground Insert has 3F geometry.
Construction Equipment and Supplies

Precision Ground Insert has 3F geometry.

Precision ground insert with 3F geometry for stainless steels, aluminum, high-temperature alloys and steels features periphery ground edges for accurate profiling and indexability. Additional features include light hones and positive geometry. Radii are available for light depths of cut and producing small corner radii. PVD grades offer layer of lubricity for reduced coefficient of friction....

Read More »
Hoses are ideal for half-bend radius applications.
Fluid & Gas Flow Equipment

Hoses are ideal for half-bend radius applications.

Models 351TC and 351ST abrasion-resistant hoses, designed for 1/2 SAE 100R1 minimum bend radius applications, are available with MSHA-accepted Tough Cover or Super Tough polymeric cover. Both offer 4,000 psi constant working pressure in sizes that range from 1/4 in. to 3/4 in. I.D. They are constructed of oil-resistant, Nitrile-based synthetic rubber tube, with 2 braids of high-tensile steel wire...

Read More »
Bending/Forming Machines make multiple bends in a single plane.
Food Processing & Preparation

Bending/Forming Machines make multiple bends in a single plane.

ET 95 vertical and horizontal press tube bending/forming machines can produce square, rectangular, U and compound shapes on round, square, rectangular and other profile tubing or flat and bar stock. They have bending tonnage of 14-58 tons and bend radii of 2 to 6 in. with tube diameters from 2.5 to 3 in. and wall dimensions from .035 up to 1 in. O.D. and .180 up to 3 in. O.D. Controls include...

Read More »
Large Crane handles rough terrain.
Material Handling & Storage

Large Crane handles rough terrain.

The 130 ton RT9000E crane provides mobility, maneuverability and pick-and-carry capabilities. It has a five section 42 to 160 ft boom that provides a 169 ft maximum tip height and 140 ft maximum radius with 3,770 lb capacity. Cab has tinted safety glass, armrest-mounted single-axis controllers, hot water heater, air fan, sliding side and rear windows, sliding skylight with electric wiper and...

Read More »
Motion Chip controls four axes at a time.
Agricultural & Farming Products

Motion Chip controls four axes at a time.

PCD-4541 4-axis motion control chip is for 2-phase unipolar or bipolar stepper motors. Sequence logic for full and half step modes is built-in, so it can output CW/CCW pulses or excitation signals directly to drive chips. Chip provides independent axis control, simultaneous start and stop of all axes, linear or S-curve acceleration and deceleration, speed change on the fly, idling pulse output...

Read More »

All Topics