Aprima Medical Software, Inc

MOSFETs are housed in TO-220 packages.

Models IXTP01N100D and IXTP02N05D high voltage depletion mode MOSFETs are normally on at 0V gate bias and require -5V gate bias to block current. Model IXTP01N100D is rated 1000V/100mA with 110 Ohm RDS(on) at VGS = 0V while IXTP02N05D is rated 500V/200mA and has RDS(ON) of 30 Ohms. Both are housed in TO-220 package for 25W at TC=25 deg C power dissipation. Applications include current regulators,...

Read More »
Electronic Components & Devices

MOSFETs have high voltage depletion mode.

IXTP01N100D and IXTP02N50D MOSFETS are normally on at 0V gate bias and require negative gate bias to block current. IXTP01N100D is 1000V/100mA rated MOSFET with 110 ohm RDS(on) at VGS=0V, while IXTP02N50D is rated at 500V/200mA with RDS(on) of 30 ohms. Both devices are housed in TO-220 package allowing for high power dissipation. Applications include level shifters, current regulators, normally...

Read More »
Digital to Synchro Converters handle high temperatures.
Electrical Equipment & Systems

Digital to Synchro Converters handle high temperatures.

Model DSPL60 requires 115V 60Hz reference input and +5 Vdc @ 20ma. Converters accept 14 bit natural binary angle and convert it into 3-wire synchro signal. Output is short circuit proof, and current limited with transient protection and thermal cutoff. Devices measure 2.6 x 3.1 x 0.51 in. and have thermally conductive encapsulant and metal top plate. Operating temperatures are 0-70 or -55 to 90...

Read More »
Reed Relay has >10E+14 ohms insulation resistance.
Electrical Equipment & Systems

Reed Relay has >10E+14 ohms insulation resistance.

Low-profile CR-Series leadless 50 Ohm reed relay switches at speeds up to 6 GHz with less than 40 ps rise times. To eliminate potential packaging stress, it is made with ceramic case that matches thermal coefficient of expansion of reed switch glass and reed lead. Capable of withstanding reflow soldering operations up to 260 deg C, it uses no internal solder, and has 1 microV typical thermal...

Read More »
Rotary Encoder Collar can be used to sense shaft speeds.
Mechanical Components and Assemblies

Rotary Encoder Collar can be used to sense shaft speeds.

Aluminum clamp-type collars can be configured with metallic targets to permit shaft speed sensing. Metallic targets can be read by customer-supplier variable reluctance sensors. Collars are unaffected by oils and coolants, and smooth bore will not damage shafts. They are available in one- and two-piece clamp-type designs with bore sizes from 1/2 in. and ODs up to 12 in. Applications include...

Read More »
Broach Set cuts keyways in 9 bore sizes.
Machinery & Machining Tools

Broach Set cuts keyways in 9 bore sizes.

Minute Man No. 10 Set consists of high speed steel broaches, bushings and necessary shims designed for cutting 1/8, 3/16, 1/4 or 3/8 in. keyways in bore sizes from 1/2 to 1 1/2 in. Push-type broaches can be used with any hand-operated arbor press or any hydraulic press with adequate throat depth. Other broach sets are available for cutting keyway sizes from 1/16 to 3/4 in. and bores from 1/4 to 3...

Read More »
Optics & Photonics

Color Camera outputs precise and detailed RGB signals.

Model IK-TF1 offers 3CCD micro prism system, C-Mount, and 10 lux sensitivity. One-piece camera provides 570 lines of resolution and 64 dB signal-to-noise ratio. Co-Site Sampling arrangement of its three 1/3 in., 410,000 pixel IT-CCDs results in capture of computer-ready color images and reduced smear. Functions include 9-step electronic shutter system (1/60 to 1/50,000 sec), automatic and manual...

Read More »
Interface Converters work with RS232, RS422 and RS485.

Interface Converters work with RS232, RS422 and RS485.

Models IC485+ and IC485+I allow standard RS232 port to communicate with individual RS422 device or with multiple devices within RS485 network. Both devices support RS422 full duplex mode as well as RS485 full or half duplex master and slave modes. Onboard LEDs indicate that device is properly powered and when device is transmitting and receiving. Six-position screw terminal block on board...

Read More »
Computer Chassis holds 8 CompactPCI cards.
Computer Hardware & Peripherals

Computer Chassis holds 8 CompactPCI cards.

MaxAir.10 7U tabletop or rack-mount microchassis is made of powder coated aluminum, has stainless steel hardware, and weighs 19 lb. Extruded aluminum cardguide maximizes airflow between slot positions and accepts standard 0.062 in. cards. Vented top and bottom EMI covers are zinc plated steel. Front plug-in power supplies provide CPCI voltages of +5, +3.3, +12 and -12. Output power ranges from...

Read More »

All Topics