Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Threadlocker/Sealant replaces lockwashers.
PERMABOND-® HH120 seals fasteners against water and chemicals. It obtains fixture strength in 15-20 min on active metals such as iron, steel, nickel, and aluminum. Viscosity is 7000 cp, allowing for gap filling up to 10 mil. HH120 features locking strength of 250-350 lb-in. and retaining strength of over 2000 psi. It is suitable for locking bolts, nuts, and screws for permanent assembly, and is...
Read More »
Gaskets are highly conductive and provide EMI shielding.
Soft GORE-SHIELD-® GS8000 EMI gaskets consist of nickel-plated base polymer, backed with thin foil layer and electrically conductive, pressure-sensitive adhesive. Less than 3.4 N/cm of pressure compresses gaskets from nominal starting thickness of 1 mm to thickness of 0.4 mm. At this point, DC resistance is less than 10 mOhm for a 19 mm-² donut, and shielding effectiveness is greater than 90...
Read More »
Chain Conveyors have modular design.
Flat-top and table-top chain conveyors are based on aluminum-profile frames with full length t-slots for assembly components, such as side-frames, drive units, supports, and guide rails. Flat-top chain choices including steel and thermoplastic are available in standard widths of 3-¼, 4, 4-½, 6, 7-½, 10 and 12 in. Conveyor chain choices include all plastic, all steel, and roller chain, with...
Read More »
Software provides energy reporting and analysis.
EnergyDirector(TM) web-based software monitors and measures energy usage of any electronic point or metered service, including gas, electric, water, and steam. It shows real-time current energy usage and allows user to generate reports and analyze current and historical data. Software provides cost comparison against on-site generation; energy cost allocation; remote control of lights, heat,...
Read More »
Cleaner removes contaminants from electronic equipment.
NT(TM) Precision Cleaner is a moderately aggressive COzol(TM) technology alternative to HCFC 141b-based cleaners. It evaporates quickly, leaves no residue, is non-flammable, and is NSF registered for use in meat and poultry plants. Formula also complies with EPA regulations on use of CFCs and HCFCs. It contains no Class I or Class II Ozone Depleting Chemicals. All 16 oz aerosol products feature...
Read More »
Gear Motors offer maximum continuous torque to 100 lb-in.
Model M1600 GIL100 PM DC parallel-shaft gear motors are available in 12 to 115 V models. All are UL-approved and feature high-energy ceramic magnets, reversible designs, double-shielded ball bearings on motor, and needle bearings on gearbox. They also include Class F insulation, dynamically balanced armature, TENV design, and auto-hook tang-type commutator. Brushes are externally replaceable.
Read More »
MIL-STD-1553 Terminal is offered in various configurations.
Mini-ACE Mark3, 3.3 V, fully integrated, MIL-STD-1553 BC/RT/MT terminal uses 0.77 in.-² board space and measures 0.13 in. high. It is offered with RT-only or BC/RT/MT functionality, 4K x 16 or 64K x 17-memory compliment, and either PCI or generic processor backend interface. Mini-ACE Mark3 works with 8, 16, or 32-bit processors with little or no glue logic while PCI Mini-ACE Mark3 series...
Read More »
Ball Bearing offers concentric mounting.
ConCentra Air Handling Ball Bearing Unit employs multi-step sleeve arrangement to form near 360-
Read More »Liquid Pumps can run dry safely and self prime.
Series 5002F pumps feature oil-less design which assures that no contaminants can be introduced into fluid. They have permanent magnetic DC motors in 6, 12, and 24 Vdc and 230 Vac 5 Hz models, as well as maximum pressure height up to 390 in. H2O for standard and chemical pH media. Models are available for standard liquid and liquid having high acid or base content. They are suitable for chemical...
Read More »Pump Pliers feature comfort grip.
Journeyman(TM) Pump Pliers measure 10 in. and have 6 machined tongue-and-grooves for smooth adjustments up to 1-¾ in. Soft, outer-surface handle material combines comfort with firm grip, while harder, inner-surface handle material is designed for toughness in harsh work environments. Pliers feature induction-hardened jaws, tension-loaded joint to reduce handle wobble, contoured thumb area, and...
Read More »