Aprima Medical Software, Inc

Safety Analyzers simultaneously test hipot and ground bond.
Test & Measurement

Safety Analyzers simultaneously test hipot and ground bond.

Featuring Twin-Port(TM) technology, Guardian 6000 Plus Series performs 5 major electrical safety tests, including AC Hipot, DC Hipot, Insulation Resistance, Ground Bond, and Open/Short. Guardian 6100 Plus also performs Leakage Current and Functional Run Tests. Results are indicated on front panel LCD display during test and overall go/no-go indication is provided. CaptivATE software creates...

Read More »
Fasteners & Hardware

Lock Cylinder adds RFID functionality to mechanical locks.

BINoXX DK 4100 Smart RFID Electronic Cylinder can replace mechanical cylinder, allowing existing contactless RFID-based access control credentials to open doors, which previously required a key. Battery-powered cylinder recognizes all major transponder types, including Hitag, MIFARE, and HID Prox. Each cylinder can be programmed to allow entry to authorized parties based on pre-set times and...

Read More »
Hydraulic Multimeters offer flow ranges of 100 or 200 gpm.
Test & Measurement

Hydraulic Multimeters offer flow ranges of 100 or 200 gpm.

Series DHM provides digital readout of pressure, peak pressure, volumetric efficiency, and hydraulic horsepower in addition to flow rate and fluid temperature. Two models are offered with peak pressure to 9,000 psi and temperature to 250°F. Display retains pressure spike values lasting at least 1 ms. Volumetric efficiency is automatically calculated and displayed by setting baseline flow and...

Read More »
Electrical Equipment & Systems

Sensor measures barometric pressure.

Measuring 9 x 9 mm, Intersema MS5534B is an SMD-hybrid device with piezoresistive pressure sensor and ADC-interface IC. With power requirement of 2.2-3.6 V, sensor measures 0-1,100 mbar with temperature range of -40 to 125°C. Output is digital with 0.1 mbar resolution and relative pressure accuracy of ±0.5 mbar. Six readable coefficients are included with sensor for software calibration....

Read More »
Laser System reveals invisible surface finish.
Test & Measurement

Laser System reveals invisible surface finish.

Class II, CE-certified OPTI-Scan can be configured to check any machined part surface and render go/no-go signal. It utilizes lasers arranged around part fixture, each aimed at machined surface of workpiece. System is first shown pre-finished master part and then properly finished master part. Quality of reflected light indicates whether surface has been correctly finished, and results are...

Read More »
Adhesives & Sealants

SL Photopolymer can be used on all solid-state platforms.

RenShape® SL 7585 photopolymer, formulated to release bubbles before processing to increase throughput, is suited for building master models and prototypes. Thermoplastic-like stereolithography (SL) material is clear amber in vat and turns white as it is exposed to laser light used in curing process. After full cure, parts built with material exhibit Shore hardness of 84D, tensile strength of...

Read More »
Absolute Multi-Turn Encoder offers 33-bit resolution.
Communication Systems & Equipment

Absolute Multi-Turn Encoder offers 33-bit resolution.

Weighing 1.0 oz, Series TRD-M35A features 1.5 in. OD modular kit design and 0.02 in. wide air gap. It provides 17-bit resolution for single turn and 16-bit for multi-turns. Equipped with serial communication interface, user can configure up to 8 axes through Bus connection with LSI signal receiver chip. Response turn speed is 6,000 rpm under normal operating conditions and 10,000 rpm during...

Read More »
Acoustic Sensor features European ATEX II 3D approval.
Sensors, Monitors & Transducers

Acoustic Sensor features European ATEX II 3D approval.

Used for continuous solids flow detection, SITRANS AS 100 is certified for use in hazardous areas and conditions where explosive dust may be present. It detects changes in high-frequency, structure borne sound waves from equipment and materials in motion, reacting instantly to changes in solids flow to warn of blockages, product absence, or equipment failure. Unit features 0-10 Vdc analog output,...

Read More »
Software delivers CNC machine simulation and optimization.
Software

Software delivers CNC machine simulation and optimization.

VERICUT v6.0 simulates CNC control G-code programs to provide virtual machining environment, and simulates CNC machining to detect errors, collisions, or areas of inefficiency. With project tree, users can view and configure multiple setups. Once user selects CNC machine configuration, stock, fixture, and design component information is attached to machine, ready to simulate machining operations....

Read More »

All Topics