Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Dual SCART operates from +3.3 and +12 V power supplies.
MAX9598 is switch matrix for routing of audio and video signals between MPEG decompression chip and 2 external SCART connectors. It integrates DirectDrive(TM) technology to prevent click-and-pop noise. Contained in 6 x 6 mm TQFN package, unit operates from 0 to +70-
Read More »RF Transceiver handles 2.3-2.7 mobile WiMAX applications.
MAX2839 zero-IF MIMO RF transceiver utilizes dual-receiver technology to deliver noise figure at 2.3 dB, -81 dBm sensitivity for 64-QAM signal at 5 MHz channel bandwidth, and 95 dB gain control range that is digitally controlled in 1 dB steps. Also, it delivers 0 dBm linear output with 64-QAM signal, greater than -45 dBc of sideband suppression, and more than -36 dB EVM. Operating from 2.7-3.6 V...
Read More »Level Shifter supports legacy displays.
Featuring 2 Gbps max data rate, quad-channel MAX9406 DisplayPort(TM)-to-HDMI(TM)/DVI(TM) Level Shifter enables PCs with DisplayPort output to directly drive HDMI/DVI-capable display, such as LCD screen. Unit can also level shift differential video data stream through PCI Express-® card to drive HDMI/DVI display. Housed in 5 x 5 mm, 32-pin and 7 x 7 mm, 48-pin packages, shifter is specified over...
Read More »Single-Channel CCFL Controller handles LCD backlighting.
Model DS3991 supports both push-pull and half-bridge drive schemes using minimal number of external components. It converts 5-24 Vdc voltage to 300-1,400 Vrms high-voltage ac waveform that is required to power CCFLs. Supporting both single- and multiple-lamp configurations, unit drives 2 logic-level, n-channel MOSFETs that are tied between step-up transformer and ground. It operates from single,...
Read More »HDMI/DVI Control Switch matches any voltage level.
Featuring 3 independent voltage inputs, Model MAX4929E is capable of switching between 2 digital video signals going into single monitor or between multiple HDMI/DVI connectors while maintaining signal integrity. Two enable inputs allow switch to operate in normal mode or high-impedance state. Providing all switching, logic-level matching, and ESD protection required to complete 2:1 HDMI/DVI...
Read More »
Crystal Oscillator Modules are offered in 9 versions.
PureEdge(TM) NBXxxxx Series uses high Q fundamental mode crystal and analog phase lock loop multiplier to provide single or dual frequency, ultra low jitter and phase noise LVPECL/CML differential output. Units feature noise floor of -163 dBc/Hz at 10 MHz offset, and phase RMS jitter of 0.4 ps. Housed in 5.0 x 7.0 mm SMD package, oscillators are suited for 1x/2x Fibre Channel, SATA, iSCSI, PCIe,...
Read More »Chipset enables multimonitor HDMI/DVI video distribution.
Fanout switch chipset is comprised of MAX3845, which provides switching, fanout, and cable driving for TMDS-® signals, and MAX4814E, which offers I-²C control of MAX3845 and handles all switching of DDC, 5 V, and HPD signals. Devices can be combined to create 2:4, 4:4, and 2:8 DVI switches with full I-²C control. Additionally, MAX3845 provides input equalization and output preemphasis as well...
Read More »Temperature Measurement Instrument is network-ready.
TEMPpoint provides standard Ethernet connection to support remote monitoring and control of thermocouples, RTDs, and voltage or resistance in field as well as on factory floor. In addition to full Class C compliance and certification for LXI, product features auto-calibration and 48 separate channels with 24-bit resolution, each with its own ADC and CJC circuit. Channel-to-channel isolation of...
Read More »Ethernet-over-PDH Mapper enables Carrier Grade Ethernet.
Supplied in 17 x 17 mm CSBGA package, DS33X162 enables delivery of new Carrier Ethernet services over existing PDH telecom infrastructure. It allows Ethernet transport from one GbE or two 10/100 Ethernet interfaces and supports up to 16 T1/E1 links or 8 DS3 links with 400+ Mbps throughput. In addition to Ethernet frame encapsulation in GFP-F, HDLC, or X.86, solution performs ingress policing,...
Read More »Software extends visibility from ERP systems to shop floor.
SAP Integration Tool makes SAP data available to ProFicient(TM) software for real-time QC on production floor. SAP framework integrates manufacturing with other critical operations, allowing accelerated response to changing requirements. SAP Import Utility connects SAP to shop floor, promoting visibility to InfinityQS users. Along with part and test data, upper/lower engineering limits and...
Read More »