ThomasNet Industrial Newsroom -

Common Mode Choke Coil is designed for USB 3.0 applications.

info@productnews.com (ThomasNet News) — Tue, 24 Nov 2009 08:33:52 -0500

With 1.2 x 1.0 mm footprint and 0.9 mm (max) profile, CM01S600 features precise wire-wound structure that enables delivery of 10 GHz typ cut-off frequency. It provides noise suppression characteristics without distorting wave pattern of high-speed differential signal interface. Along with 60 X @ 100 MHz typ common mode impedance, characteristics include 0.4 X max DC resistance, 300 mA max rated current, 20 V max rated voltage, and 100 MX min dielectric frequency.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Choke Coils

Wirewound Chip Inductors suit DC-DC converter applications.

info@productnews.com (ThomasNet News) — Fri, 06 Nov 2009 08:43:11 -0500

Series LQH3NP_J0 series wirewound chip inductors has low profile (1.2 mm max), and is available in 1.0-47 µH denominations. The series features low DC resistance, down to 0.040 Ohm, and rated current up to 1.62 A is supported. All parts are magnetically shielded to avoid electromagnetic interference with surrounding circuitry. Maximum footprint is 3.2 x 3.2 mm.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Chip Inductors | Wirewound Inductors

Ceramic Inductors target aerospace and military markets.

info@productnews.com (ThomasNet News) — Tue, 20 Oct 2009 08:41:25 -0500

Suited for mission-critical applications, ML Series 0603-size inductors offer inductance values of 47 nH to 22 µH and Q ratings as high as 50 at 250 MHz with self resonant frequencies as high as 16 GHz. Ceramic construction provides high current handling, while high-temperature encapsulant enables operation in ambient temperatures from -55 to 155°C. Featuring COTS Plus, tin-silver-copper, and tin-lead terminations, units offer MTBF of 1 billion hr.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Chip Inductors | High Current Inductors | Military Specification Inductors | Power Inductors

Coils suit solenoid valves in hazardous environments.

info@productnews.com (ThomasNet News) — Wed, 16 Sep 2009 08:23:32 -0500

Suited for use in Lucifer stainless steel solenoid valves as well as brass and aluminum X valves, "d mb" and "ia" ATEX-certified 37 mm Electrical Coils meet T6 temperature classes. Stainless steel fittings and IP67 protection level permit coils to be used where ambient constraints are hard, aggressive, and sometimes corrosive. By using booster technology for "ia" product, current consumption is reduced to 20-15 mA, allowing usage in markets with intrinsically safe electrical circuits.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Solenoid Coils | Electric Coils

Sample Kit offers choice of transponder coils.

info@productnews.com (ThomasNet News) — Fri, 11 Sep 2009 08:35:08 -0500

Sample kit for automotive electronics developers is offered in type with B82450A series transponder coils, with dimensions of .8 x 2.7 x 2.7 mm3 and 11.4 x 3.5 x 3.5 mm3. Coils cover inductances from 1.0-7.0 mH and have sensitivity from 10-51 mV/µT. Kit is also available with B82451N series coils, at 7.7 x 7.7 x 2.65 mm3, and contained for polarization in z coordinate. Rugged inductors are designed for frequency of 125 kHz and operate in temperatures from -40 to +125°C.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Induction Coils | Kits

Round Wire Coil Power Inductors resist thermal aging.

info@productnews.com (ThomasNet News) — Fri, 04 Sep 2009 08:26:15 -0500

Measuring 7.6 x 7.4 x 6.4 mm, Model PG0871NL features DCR of 1.5-31.5 mW and tolerance of ±8%, with inductance values from 0.46-10.5 µH and saturation current from 6.3-28 A. Measuring 10.8 x 9.2 x 8 mm, PG0702NL offers DCR of 0.68-7.7 mW with tolerance of ±6%, inductance values of 0.30-6.8 µH, and saturation current of 8.5-42 A. Both SMT units operate in temperatures from -40 to +130°C and feature 3-pin design to ensure mechanical stability. Ferrite core material resists thermal aging.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Surface Mount Inductors | Power Inductors | Ferrite Inductors | Wirewound Inductors

Radial Leaded Inductors handle temperatures of -20 to +80°C.

info@productnews.com (ThomasNet News) — Wed, 26 Aug 2009 08:28:56 -0500

Designed to provide EMI/RFI protection in current handling applications up to 8.4 A, DR217 Series is available with inductance range from 1.0 µH to 150 mH depending on model, and DCR of 0.008-520 W maximum over maximum current rating from 8.4-0.045 A. Inductors feature through-hole wirewound coil design, and come in round packages sized from 0.196-0.551 in. dia, with lead spacing from 0.78-0.295 in., depending on model. Series is suited for high-temperature soldering.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Wirewound Inductors | EMI/RFI Suppression Inductors

Compact Wire-Wound Power Inductor offers optimal DC bias.

info@productnews.com (ThomasNet News) — Mon, 17 Aug 2009 08:30:12 -0500

Supplied in 3 x 3 x 1.2 mm package, NRV3012 is intended for LED flash DC-DC converter applications in camera-equipped cell phones and other portable electronic devices. Its 1.8 A rated current is based on DC saturation, and max temperature rise current is 1.10 A. Sleeveless, square-core winding eliminates wasted space and thickens lead wire inside inductor to achieve minimal DC resistance (0.120 X). Along with ferrite construction, features include inductance of 2.2 µH.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Wirewound Inductors | Power Inductors

Inductive Chokes target inverters in wind turbines.

info@productnews.com (ThomasNet News) — Mon, 20 Jul 2009 08:34:28 -0500

Using core materials made of powder composites specifically engineered for individual application, Inductive Chokes have low eddy current and hysteresis losses. Through encapsulated design, chokes also achieve low-intensity stray fields, enabling other components to be placed in close vicinity without risk of magnetic interaction. Maintenance-free, RoHS-compliant units have been tested and approved for use in offshore installations.

This story is related to the following:
Electronic Components and Devices
Green & Clean

Search for suppliers of: Inductor Chokes

Shielded Inductors provide power line filtering.

info@productnews.com (ThomasNet News) — Wed, 10 Jun 2009 08:27:54 -0500

Featuring integral ferrite shield, Series 1200RS and 1200LRS are suited for power line filtering in low to medium current applications such as switching power supply circuits. Through hole, radial leaded devices have overall dimensions of 10.5 mm dia x 8.5 mm. Operating from -40 to +85°C, Series 1200LRS offers inductance values from 6.8 µH to 22 mH and DC current rating up to 4.7 A IDC, while Series 1200RS features inductance from 10 µH to 1 mH and max current rating of 4.6 A IDC.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Shielded Inductors

Power Inductor offers inductance values from 0.36-1.30 µH.

info@productnews.com (ThomasNet News) — Mon, 01 Jun 2009 08:22:51 -0500

Suitable for motherboard and computer power applications, HM58 Series high-current low-loss cube inductor features heavy-gauge coil wire and exhibits saturation current rating up to 60 A at frequencies to 1 MHz. It has operating temperature range from -40 to +125°C and is available in standard tray packaging. DCR ratings are from 0.65-1.05 mW, with tolerances to ±5%. With through-hole configuration and 3 open sides, device requires footprint of only 11 x 11.5 mm.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: High Current Inductors | Power Inductors

Dual Winding Inductor may be configured multiple ways.

info@productnews.com (ThomasNet News) — Thu, 28 May 2009 08:33:17 -0500

Suited for use in consumer electronics, surface-mount HM78D Series can be configured as inductor, common mode choke, or DC/DC converter. It is also specified for use in SEPIC applications and can be configured as 2 single inductors connected in series or parallel or as 1:1 transformer. Rated current inductance from 1.176-4,036 µH when connected in series and 0.33-1,000 µH in parallel, and max DC resistance ranges from 0.0295-15.6 ohm and 0.0074-3.89 ohm, respectively.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Surface Mount Inductors

Surface Mount Chokes protect data lines from EMI/RFI.

info@productnews.com (ThomasNet News) — Fri, 24 Apr 2009 08:38:46 -0500

Measuring 9.15 x 6.0 x 5.2 mm and 9.15 x 6.0 x 4.8 mm, respectively, low-profile, common mode DR332-1 and -2 Choke Series minimize radiated/common mode conducted emissions on balanced twisted pair transmission lines and pass differential mode dc currents and signals. Operating in temperatures from -40 to +85°C, units feature inductance range of 5-4.7 mH and current range of 2.5-0.2 A. RoHS-compliant units operate over a wide frequency range to more than 100 MHz.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Surface Mount Chokes | EMI/RFI Suppression Chokes | Common Mode Chokes

Automotive Power Inductor is rated for 180°C operation.

info@productnews.com (ThomasNet News) — Mon, 09 Mar 2009 08:32:13 -0500

Featuring powdered iron alloy core material, HA55 Series is designed for automotive underhood environments. Products have current inductance values from 7-20 µH, and recommended frequency is up to 400 kHz, depending on device. Rated current range is from 40-60 A, with saturation current from 43-50 A, and DC resistance is from 1.7-3.35 mW. Operating temperature range starts from -40°C to +180°C.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Custom Inductors | High Current Inductors | Power Inductors

High Current Inductor is offered in 6767 case size.

info@productnews.com (ThomasNet News) — Wed, 04 Mar 2009 08:32:12 -0500

Featuring 17.15 x 17.65 mm footprint and 7.0 mm profile, IHLP-6767GZ-01 delivers maximum frequency to 2 MHz, DCR down to 0.63 m typical, and standard inductance values from 0.22-10 µH. It offers saturation current range of 25-129 A, heat rating current range from 12.5-44 A, and handles high transient current spikes without hard saturation. Specified for operating temperature of 55 to +125°C, device has resistance to thermal shock, moisture, mechanical shock, and vibration.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: High Frequency Inductors | Shielded Inductors | High Current Inductors

Power Inductors feature military-approved design.

info@productnews.com (ThomasNet News) — Fri, 27 Feb 2009 08:31:53 -0500

Added to military's DSCC Qualified Products List, MLP5025 Series is qualified to MIL-PRF-27/367A, while MLP1812 Series meets MIL-PRF-27/368A, and MLP8527 Series meets MIL-PRF-27/370A. Series MLP5025 features inductance range of 0.22-22,000 µH, 7.00-.050 A current rating, and max DCR of .0080-160 W, while Series MLP1812 features 1.0-330 µH, 1.050-.090 A, and .113-15.240 W, and Series MLP5025 is rated at 6.27-.09 A with 1.0-18,000 µH inductance and .009-40.0 W max DCR.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Power Inductors | Military Specification Inductors

Low-Loss Chokes target railway applications.

info@productnews.com (ThomasNet News) — Mon, 23 Feb 2009 08:33:13 -0500

Limiting input on primary side, Low-Loss Chokes for inverters are vibration- and impact-resistant with voltage rise up to 10 kV/µs and magnetostriction-free material for quiet operation. UL-listed, Class H insulation system provides thermal protection up to 180°C. With coating that protects against dust and water, IP66-rated chokes can be fitted outside inverters, eliminating need for cooling fans, and saving both energy and installation space.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Chokes

Winged Inductor has range from 0.10-10 µH.

info@productnews.com (ThomasNet News) — Thu, 12 Feb 2009 08:29:22 -0500

Featuring profile of 1.2 mm for both sides of cut-out PCBs, IHLW-5050CE-01 offers saturation current range from 14-84 A, typical DCR from 0.8-30.4 mW, and maximum DCR from 0.96-34 mW. With frequency range up to 5 MHz, product can be used for voltage regulator module and dc-to-dc converter applications. RoHS-compliant, it is specified for operating temperature range of 55-125°C and offers resistance to thermal shock and moisture.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Shielded Inductors | High Current Inductors

High Energy Chokes are suited for renewable energy industry.

info@productnews.com (ThomasNet News) — Mon, 02 Feb 2009 08:35:02 -0500

Offered in 3 different formats: 100, 120, and 180 mm high, and 100 and 120 mm in dia, POT CORE series can be used both as input and output chokes for solar, wind, and fuel-cell inverter applications. Due to its completely shielded format, series is ideal solution to avoid electromagnetic noise through choke. Available in one- or two-cell format (dual inductor), products have current capability of 44 A, and operating frequencies up to 25 KHz.

This story is related to the following:
Electronic Components and Devices
Green & Clean

Search for suppliers of: Inductor Chokes

Inductors feature operating temperature range of -40 to 85°C.

info@productnews.com (ThomasNet News) — Thu, 29 Jan 2009 08:33:20 -0500

Suited for low and medium current applications and high density circuits, RoHS compliant, low DC resistance 1100R and 1300R series are fully backward compatible with Sn/Pb soldering systems. Measuring 4.0 mm dia x 5.5 mm, 1100R series offers inductance values ranging from 1.0-470 µH and has maximum current ratings of 0.14-3.0A. Series 1300R measures 8.0 mm dia x 10 mm, has inductance values of 1.5 µH to 68 mH, and maximum current ratings between 0.04-6.3 A.

This story is related to the following:
Electronic Components and Devices

Search for suppliers of: Output Filter Inductors | Power Inductors