ThomasNet Industrial Newsroom -

Compact Power Line Filters feature slide-in mounting.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 20 Aug 2008 07:36:54 -0500

Intended for quick mounting in panel openings, SRB Slide-In Power Line Filters are available with 33-1,000 pF capacitance range. Featuring IEC 320 male power connection and measuring 0.96 in. deep, shielded filters are suited for space-constrained communications, computer and consumer electronics, industrial and commercial, instrumentation, and medical equipment applications. UL Recognized, CSA Certified, and VDE approved filters are rated up to 15 A at 250 Vac, 50/60 Hz.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Electronic Components and Devices Sponsored by: Lumera Corporation -

Search for suppliers of: Power Line Filters | IEC Connector Filters

Power Conditioners come in models ranging from 120-3,000 VA.

info@productnews.com (ThomasNet Industrial Newsroom) — Mon, 18 Aug 2008 07:38:31 -0500

ONEAC® PCm Series eliminates power contaminants and limits peak voltage and edge-speed of electrical transients by employing low impedance isolation transformer and Virtual Kelvin Ground® to remove full spectrum of power line noise in Common and Normal modes. Conforming to IEC60601-1 standards, medical grade power conditioners come with hospital-grade plugs and receptacles and in 120 and 230 V, 50/60 Hz with IEC connectors to facilitate country-specific connector compatibility.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Power Line Conditioners

Power Relay Module is supported by PXI compliant 3U chassis.

info@productnews.com (ThomasNet Industrial Newsroom) — Mon, 11 Aug 2008 07:46:23 -0500

Supporting high current and high voltage switching applications, model 40-330 SPST Power Relay Module provides 24 off SPST switches, each capable of switching currents up to 4 A and hot switching voltages up to 250 Vac. Cold switch rating of 1,000 V peak permits unit to be used for high voltage test applications where hot switching is not needed. User connections are provided on 50 way male high voltage D Type connector. Module includes software support for common programming environments.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Switching Relays | Programmable Relays | Power Relays | High Voltage Relays | Power Entry Modules

EMI Filter has 15-100 V range.

info@productnews.com (ThomasNet Industrial Newsroom) — Mon, 11 Aug 2008 07:46:20 -0500

Suited for wide range of applications such as automotive, avionics, telecom, and ground systems, Model PFL4000 EMI filter is designed to meet filter requirements of conducted emissions per MIL-STD-461E for 5-100 W dc/dc converters. It features 99.5% efficiency, MTBF of 47.6 million hr, 6-sided shielding, and thermally conductive epoxy packaged in 1 x 2 x .5 in. metal case.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Communication Systems and Equipment

Search for suppliers of: EMI/RFI Filters

Common Mode Filter suppresses EMI on DisplayPort interfaces.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 01 Aug 2008 07:51:03 -0500

Measuring 1.25 x 1.0 x 0.6 mm, TCM1210U-500-2P wide-band thin-film common mode filter suppresses noise on DisplayPort connections for signal transmission between computers or audiovisual equipment and display monitors. DisplayPort link uses up to 4 lines, each rated for 2.7 Gbit/sec, resulting in total transfer rate of 10.8 Gbit/sec. Unit features 8.0 GHz cutoff frequency, 50 <font face='Symbol'>W</font> common mode impedance at 100 MHz, 100 mA rated current, and 10 V rated voltage.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Electronic Components and Devices Sponsored by: Lumera Corporation -

Search for suppliers of: Retrofit EMI Suppression Filters | Electronic Filters

DC Front End Module comes in 2.28 x 2.2 x 0.5 in. package.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 31 Jul 2008 07:42:15 -0500

Providing EMI filtering and transient protection, M-FIAM9 28 V front-end module meets conducted emission/susceptibility per MIL-STD-461E and input transients per MIL-STD-704A/E/F and MIL-STD-1275A/B/D. With input voltage of 10-36 Vdc and output power up to 500 W, ruggedized unit can be mounted onboard or inboard for height-critical applications. It comes in 2 environmental grades, including -55 to +100ºC operating and -65 to 125ºC storage, with 4 pin and 3 baseplate options.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Communication Systems and Equipment

Search for suppliers of: Transient Voltage Surge Protectors | Military EMI/RFI Filters | Power Modules

EMI Filter Adapters come with 9, 15, 25, or 37 pins.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 30 Jul 2008 07:55:06 -0500

Available in 4 standard filter values from 47-3,900 pF, male and female D-Sub filter adapters provide electronic noise reduction in applications ranging from high-speed digital broadcasting to industrial test equipment. They are suited for both EMI corrections in existing applications or for filter tests during design phase. Adapters complement D-Sub filter SMC connectors as retrofit solution for system protection against electromagnetic radiation without PCB redesigns.

This story is related to the following:
Communication Systems and Equipment
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: EMI/RFI Filters | Adapters

Power Quality Filters help calm harmonic waves.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 22 Jul 2008 07:43:58 -0500

ECOsine(TM) load-applied passive harmonic filters are suited for 3-phase power electronics with 6-pulse rectifier front ends. With total harmonic current distortion of under 5%, products guarantee compliance with IEEE 519 and other international power quality standards. Two ranges are available, one for 380-500 V, 50 Hz grids (FN 3410 series) and one for 440-480 V, 60 Hz systems (FN 3412 series). Plug-and-play concept facilitates installation, wiring, and commissioning.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Electronic Components and Devices Sponsored by: Lumera Corporation -

Search for suppliers of: Power Line Filters | Harmonic Filters

Audio IC combines handset audio filtering and ESD protection.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 10 Jul 2008 07:27:57 -0500

From 2.42 x 1.92 x 0.65 mm flip-chip package, EMIF06-AUD01F2 implements complete EMI filtering and ESD protection for stereo headset output and external/internal microphones. Audible handset demodulation noise is eliminated by achieving -25 dB attenuation throughout stop-band 800-2,480 MHz using high-density 1.3 nF PZT capacitors on microphone lines. ESD protection is achieved via combination integrated TVS diodes, low-inductance packaging, and Z-R-Z pi-filter topology.

This story is related to the following:
Communication Systems and Equipment
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Electronic Components and Devices Sponsored by: Lumera Corporation -
Materials and Material Processing

Search for suppliers of: EMI/RFI Filters | Integrated Circuits (IC) | ESD Products

Filter Architecture boosts mobile handset signal integrity.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 08 Jul 2008 07:41:07 -0500

Based on coupled inductor design, Praetorian® III LC filter architecture utilizes 6-pole pi-filter topology and enables design of filters that can fit into small form factor, 0.4 mm pitch uDFN and chip scale packages. Filters, optimized for inductance and capacitance (down to 10 pF), promote attenuation and signal integrity. Products based on this architecture address EMI filter and ESD protection (to 15 kV) requirements found in handset designs.

This story is related to the following:
Materials and Material Processing
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Electrostatic Filters | Electromagnetic Filters

Electronic RF Filters are designed for shielded enclosures.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 06 Jun 2008 07:28:10 -0500

Mounted through outer wall of shielded enclosure, Series FCP power line penetration filters are RFI-secure and supplied with threaded nipple. Products are supplied with bleeder resistors to prevent shock hazards and can withstand 140% of rated current for 15 min without any deterioration. Providing specified insertion loss of 100 db min over indicated frequency range, series filters from 60-400 Hz with 100 db attenuation from 14 KHz to 10 GHz and 100 KHz to 10GHz.

This story is related to the following:
Communication Systems and Equipment
Electronic Components and Devices Sponsored by: Lumera Corporation -
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Radio Frequency Interference (RFI) Filters | Power Line Filters | Interference Filters | Military EMI/RFI Filters | EMI/RFI Filters | Electronic Filters

EMI/RFI Filters meet MIL-F-15733 specification.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 16 May 2008 07:35:10 -0500

Dual and triple circuit power line electronic filters run at operating temperatures from -550 to +850°C; voltage ratings are 115 Vac, 400 Vdc, O-400 Hz. With minimum insertion loss characteristics, MIL-F-15733/75 filters suit variety of noise and interference filter and safety requirements of electro-magnetic compatibility. Also available is single circuit power line filter IAW to MIL-F-15733.

This story is related to the following:
Communication Systems and Equipment
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Electronic Components and Devices Sponsored by: Lumera Corporation -

Search for suppliers of: EMI/RFI Filters | Electronic Filters

Power Filters are optimized for DC applications.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 06 May 2008 07:40:37 -0500

Particularly suited for applications requiring increased attenuation of asymmetric disturbances, FMEB and FMEC series have current rating of 30 A @ 80 Vdc and aluminum housing that is potted and has metal flanges for secure mounting to chassis. Single polarity FMEB filter is designed for max operating voltage of 80 Vdc, while FMEC series offers connections for 2 polarities for 80+ Vdc max. Input side is equipped with screw clamps, and output has 6.3 x 0.8 mm quick connect terminals.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Test and Measuring Instruments

Search for suppliers of: Power Line Filters | Noise Filters

DIN Rail Filters protect against surges, transients.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 02 May 2008 07:58:19 -0500

Designed for mounting on DIN rails, STFE Elite Series protects against voltage transients and surges that may impair operation of industrial and machine tool equipment. Combination of hybrid-clamping network and Active Tracking® Filter technology allows products to continuously track input ac power line and respond instantly to extraneous high-frequency noise and high-voltage transients. Filters have UL-Listed surge current capacity of 45,000 A.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Power Line Filters | Transient Voltage Surge Protectors | Surge Protectors

Inlet Filters feature earth line choke.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 23 Apr 2008 07:44:46 -0500

Model FN9233E IEC inlet filter includes earth line choke that helps reduce interference signals on ground wire. They are designed for maximum continuous operating voltage of 250 Vac, 50/60 Hz and frequency range of DC to 400 Hz. Also featuring current rating of 1-15 A at 50°C maximum as well as operating temperature range of -25 to +85°C, devices have MTBF of 1,710,000 hr at 40°C/230 V. Units are available in hot inlet versions or low leakage current versions suited for medical applications.

This story is related to the following:
Communication Systems and Equipment
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Electronic Components and Devices Sponsored by: Lumera Corporation -

Search for suppliers of: EMI/RFI Filters | IEC Connector Filters

EMI/RFI Filters are intended for noise generating equipment.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 18 Apr 2008 07:54:52 -0500

Offering hermetically sealed filter solution, FCL-660 Series RFI/EMC filters are available for 5-300 A circuits. Nosie interference filters are designed for low level interference and are suitable for use in screen rooms, medical apparatus, induction heaters, and other noise generating equipment.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Communication Systems and Equipment

Search for suppliers of: EMI/RFI Filters

DC Power Entry Module is suited for 48 V telecom equipment.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 25 Mar 2008 07:38:51 -0500

Series 5003 ECO includes screw mount version for front or rear mounting to chassis as well as snap-in version that features AMP Universal MATE-N-LOK and Molex HCS-125 connectors encased with single stage filter rated up to 15 A at 125 Vdc. EMI filter provides wideband attenuation in frequencies ranging from 100 kHz to 30 MHz. Offered in lightweight and environmentally friendly compact package, dc power entry module is ENEC and cURs approved and complies with IEC/EN 60950 standard.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: DC Power Systems | Power Entry Modules

AC Power Line Filters suit high-current applications.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 20 Mar 2008 08:19:40 -0500

CORCOM single- and 3-phase filters, offered in variety of series, meet performance requirements for conducted noise and are designed for high-current (30-400 A) applications. Offering elevated insertion loss over 10 kHz to 30 MHz range, products aid in immunity/susceptibility compliance. All BCF, FCD, and CFN series filters are delta wound and offer voltage ratings of 277/480 VAC. Model 60VS6 of S series single-phase power line filter is rated 250 Vac.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Power Line Filters

Power Entry Module includes EMI filter.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 26 Feb 2008 08:00:43 -0500

Available with current ratings of 20 A or 16 A, depending on attenuation requirements, 5130 ECO IEC Inlet meets demands of IT, medical, and industrial applications. Positive electrical contact of metal flange or snap arms to chassis ensures optimal filtering and shielding. Flange version is available for front or rear mounting with traditional screws and nuts or rivet mounting. For rear mounting only, version is available with pre-formed threaded holes for M3 screws.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Power Entry Modules

Devices combine ESD protection and EMI filtering.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 13 Feb 2008 07:37:22 -0500

Housed in 0.6 mm high SOT883 package with 1.0 x 0.6 mm footprint, Model EMIF01-1003M3 is designed for single-line applications. Dual-channel Model EMIF02-1003M6 comes in 1.0 x 1.45 mm Micro QFN package with mounted height of 0.55 mm. Both devices achieve 15 kV air discharge and 8 kV contact discharge, in accordance with IEC61000-4-2 specification. When subjected to 15 kV ESD strike, Model EMIF01 delivers 9 V clamping voltage and Model EMIF02 provides 17 V.

This story is related to the following:
Electronic Components and Devices Sponsored by: Lumera Corporation -
Communication Systems and Equipment
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Materials and Material Processing

Search for suppliers of: Integrated Circuits (IC) | EMI/RFI Filters | Electromagnetic Filters | ESD Products