ThomasNet Industrial Newsroom -

Polycarbonate Films offer protective coating for electronics.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 27 Nov 2007 07:54:03 -0500

Lexan DMX polycarbonate films include Lexan DMX 1HD00-112 film that is polished on both sides and Lexan DMX 1HDA3-112 film that is polished on one side and matte on other. Featuring layered construction that utilizes DMX resin, films offer pencil hardness rating of 1H as well as impact, chemical, saltwater, and isopropanol resistance. They can be fabricated with Insert Mold Decoration graphics and be thermoformed to greater than or equal to 35 mm draw depth.

This story is related to the following:
Chemical Processing and Waste Management
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Materials and Material Processing
Paints and Coatings Sponsored by: Omni Metal Finishing, Inc. - Finishing with Excellence

Search for suppliers of: Electronic Coatings | Resin Coatings | Polycarbonate Film

Ceramic Compound insulates high temperature resistors.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 12 Jun 2007 07:53:42 -0500

Silica-based Ceramacoat(TM) 512N is suited for insulating circuit breakers and high temperature electrical components such as heaters, electrical feed-thrus, PTC devices, rheostats, and temperature sensors. Material properties include temperature resistance of 2,400Â°F, 250 V/mil dielectric strength, and 109 volume resistivity. Available in pint, quart, and containers, moisture- and chemical-resistant single-part paste can be dispensed through manual syringes or pressurized dispensing equipment.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Electronic Insulators | High Temperature Insulators

Fiberglass Sleeving suits motor repair applications.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 22 Mar 2007 07:43:39 -0500

Available in Grade C, Acryflex-MRÂ® is manufactured by impregnating and coating finely braided fiberglass sleeving with dielectric film of acrylic resin. It is fully compatible with most magnet wire coatings such as polyester, acrylic, polyamide, polyimide, epoxy, and phenolic. Ranging in size from Â½ in. to No. 24, Class 155Â°C electrical insulation is suited for leads and crossovers on fractional and integral horsepower motors.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Electrical Insulation Sleeving | Fiberglass Sleeving

Insulator Coating minimizes required electrical maintenance.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 08 Dec 2006 07:43:32 -0500

Applied once, SylgardÂ® HVIC+ provides long-term water repellency/hydrophobicity to protect against power distribution interruptions due to increased leakage current, dryband arcing, and flashover from salt spray, industrial pollutants, and desert sand. One-part silicone high voltage insulator coating (HVIC), unaffected by salt air, rain, and humidity, exhibits tracking resistance and prevents contaminants on insulator surface from becoming wet and producing conductive layer.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Paints and Coatings Sponsored by: Omni Metal Finishing, Inc. - Finishing with Excellence

Search for suppliers of: Electrical Insulation Coatings | Hydrophobic Coatings

Single-Pole Connection Products withstand harsh areas.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 27 Oct 2006 07:41:43 -0500

Rhino-HideÂ® 49 Series is comprised of male and female plugs, connectors, receptacles, insulators, and contacts suited for land-based and off-shore oil drilling rigs. Products are engineered to deliver up to 1,000 V ac or dc power and up to 1,135 A of continuous power. Accessory products, also available, include clevis pins, receptacle castings, dust cover caps, gaskets, and couplers.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Insulators | Harsh Environment Connectors | Electric Receptacles

Machinable Ceramic operates continuously at 1,600Â°F.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 14 Jun 2006 07:51:06 -0500

Acting as ceramic thermal insulator, M/M 1600 Glass Mica Composite features fine grain construction and enables components to be machined from compression molded sheets using conventional cutting tools. Material exhibits 1.02 W/mÂ°C thermal conductivity, ~300 sec tracking and arc resistance, and 500 V/mil dielectric strength. It comes in 8 in. dia discs ranging from 1/16 to 1 1/8 in. thick and 17 x 17 in. sheets in thicknesses to 1Â¼ in.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Materials and Material Processing

Search for suppliers of: Ceramic Materials

Thermoset Composite electrically insulates transformers.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 05 May 2006 08:10:16 -0500

Used to separate and isolate electrical contacts, oil-resistant NP613 maintains mechanical strength when used in oil-filled transformer equipment. It also maintains dimensional stability at elevated operating temperatures, guaranteeing contact will be separated and engaged as needed. Constructed from electrical grade of kraft paper and modified resin, NP613 has flexural strength of 27,000 psi, compressive strength of 40,000 psi, and max operating temperature of 140Â°C.

This story is related to the following:
Chemical Processing and Waste Management
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Materials and Material Processing

Search for suppliers of: Composite Materials | Thermosetting Resins | Transformer Insulation

Ceramic Compound insulates circuit breaker contacts.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 29 Mar 2006 07:05:06 -0500

Ceramacoat(TM) 512N silica-based ceramic compound offers temperature resistance of 2,400Â°F, dielectric strength of 250 V/mil, and volume resistivity of 109. Single-part paste can be dispensed through manual syringes or pressurized dispensing equipment, and has set time of 4-6 hr at room temperature followed by curing at 200Â°F and 300Â°F for 1-2 hr, respectively. Compound is also suited for insulating wide range of high temperature electrical components.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Ceramic Insulators | High Temperature Insulators

Coating System electrically insulates ceramic resistors.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 28 Sep 2005 07:13:25 -0500

As single-part, water-based, inorganic-ceramic coating system, Cerama-Dip(TM) 538N electrically insulates high-power ceramic resistors in applications to 2,600Â°F. Odorless, non-outgassing product contains no VOCs and features volume resistivity of 109 ohm-cm and dielectric strength of 225 V/mil at room temperature. Curing is accomplished by air-drying at room temperature for 1-2 hr then step curing for 1 or 2 hr at 200Â°F and 350Â°F, respectively.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Paints and Coatings Sponsored by: Omni Metal Finishing, Inc. - Finishing with Excellence

Search for suppliers of: Electrical Insulation Coatings | Ceramic Coatings | Resistor Coatings | High Temperature Coatings

Adhesive/Coating System insulates induction heating coils.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 24 Mar 2005 00:38:54 -0500

Pyro-Puttyâ"¢ 677 single-part, water-dispersed, alumina-silica based adhesive and coating system is suited for electrical insulation and bonding applications to 2,400Â°F. Thixotropic product is supplied in paste consistency with viscosity of 43,000 cps and specific gravity of 2.17 g/cc. After application, it dries at room temperature in 1-4 hr and cures in 2 hr at 200Â°F. Material produces hard shell that protects induction coils from high temperature oxidation.

This story is related to the following:
Adhesives and Sealants Sponsored by: Henkel Corp. - World Leader in Adhesives, Sealants & Surface Treatments
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: High Temperature Adhesives | Electrical Insulation Coatings

Adhesive acts as thermal and electrical insulator.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 27 Apr 2004 07:53:37 -0500

TRA-BOND 293-21 general-purpose adhesive adheres to gold, nickel, silver, and brass substrates. With lap shear strength up to 5,000 psi, product has work life of 3 hr and cures in 45 min at 120Â°C. Material comes in pre-mixed, frozen syringes, and, at optimal storage conditions, has shelf life of up to 1 year.

This story is related to the following:
Adhesives and Sealants Sponsored by: Henkel Corp. - World Leader in Adhesives, Sealants & Surface Treatments
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Electrical Insulators | Adhesives

Machine Screw Insulators protect transistors and discretes.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 18 Feb 2004 07:49:10 -0500

Made from UL-rated, 40% glass-filled Polyphenylene Sulfide, insulators come in shoulder design, flush low-profile, and dual-sided, low-profile configurations with stand-offs for added ventilation of mounted devices. Accommodating screws up to 0.125 in. dia, units provide grounding protection in applications up to 260Â°C and are chemically inert with oxygen rating index over 45%. Applications include power supplies, inverters, transistors, and discretes.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: High Temperature Insulators | Electrical Insulators

Ceramic Insulators suit electrical and thermal environments.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 04 Feb 2003 07:53:52 -0500

Machineable ceramic components perform in environments with temperatures to 1,000Â°C and thermal conductivity to 2,800Â°C, depending on material. Products offer tolerances to Â±.0001 in. as well as flatness and parallelism within Â±.0001 in. per 12 in., depending upon part material and configuration. Insulators can be precision machined from MycalexÂ®, MykroyÂ®, ArclexÂ®, Grade A LAVA, Boron, Nitride, MacorÂ®, and ceramic filled materials.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Materials and Material Processing

Search for suppliers of: Machinable Ceramics | Ceramic Insulators

Insulator Material guards against humidity.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 09 May 2002 07:47:33 -0500

Voltoid(TM)D-800 resin-bonded, cellulose-fiber composite can be fabricated into gaskets, insulators, lead separators, backing-plate barriers and other electrical insulation configurations. It is recognized by Underwriters Laboratories for continuous use as electrical and mechanical barrier to 105 deg C. Insulator is available in sheets in thicknesses of 0.031 to 0.125 in. It is easily fabricated by punching and blanking.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Insulators

Transistor Insulator works in high temperatures.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 11 Dec 2001 13:39:36 -0500

RTC Series insulates tab of transistor package from screw holding transistor tab down to heat sink for consistent heat transfer. It can withstand temperatures of up to 130 ÂºC. Insulator is flame retardant and made of glass filled material.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Transistor Insulators