ThomasNet Industrial Newsroom -

Miniature IR Receivers feature 2 photodiodes.

info@productnews.com (ThomasNet News) — Tue, 03 Nov 2009 08:38:25 -0500

Series TSOP75xxxW ultra-miniature SMD IR receivers include 2 photodiodes and metal EMI shielding in package with 2.35 mm profile. Lens-less products offer irradiance from 0.3-0.7 mW/m<sup>2</sup> over wide angle of ±75°. Operating from supply current of 0.35 mA typical at 3.3 V, units have supply voltage range of 2.5-5.5 V and operate over carrier frequency of 30-56 kHz. They are insensitive to supply voltage and ripple noise and offer immunity against ambient light.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Infrared Receivers

Gateways make ultra broadband available throughout home.

info@productnews.com (ThomasNet News) — Mon, 02 Nov 2009 08:40:54 -0500

Delivering ultra-broadband IP-based voice and data services, SURFboard® DOCSIS 3.0 Wireless Modems and Gateways support GigE home networking and channel bonding of up to 8 downstream and 4 upstream channels with data rates up to 300 Mbps downstream and more than 100 Mbps upstream. Remotely manageable units are equipped with 4-port GigE switch and integrated 802.11n Wi-Fi® access point, as well as built-in firewall with Stateful Packet Inspection, intrusion detection, and DoS attack prevention.

This story is related to the following:
Communication Systems and Equipment
Computer Hardware and Peripherals
Green & Clean

Search for suppliers of: Wireless Modems | Gateways

Wireless Communication Boards handle analog/digital/serial data.

info@productnews.com (ThomasNet News) — Thu, 29 Oct 2009 08:32:04 -0500

Measuring 4 x 4 in., vWire(TM) boards act as wireless 'virtual cables' to provide simultaneous analog, digital, and serial connections between 2 or more sites located up to 1 mile apart. They can also be used within peer-to-peer PAN network to wirelessly access remote analog and digital signals from multiple vWire boards. I/O includes up to 6 optically isolated digital inputs and relay outputs, 2 analog inputs, 2 analog outputs, and RS232. Multiple antenna options are also available.

This story is related to the following:
Computer Hardware and Peripherals
Communication Systems and Equipment

Search for suppliers of: Communications Boards | Wireless Data Communication Adapters

UHF Devices extend range of wireless car access systems.

info@productnews.com (ThomasNet News) — Tue, 20 Oct 2009 08:41:20 -0500

Supplied in 32-pin, 5 x 5 mm QFN package, sub-1 GHz CC11x1-Q1 Series transmitters, receivers, and transceivers have RF design and SPI that eliminate need for external filters or switches. Devices allow migration from unidirectional to bidirectional systems and support operation up to +125°C. They help designers build reliable data links with fast frequency hopping scheme (88 µs switching time) utilizing fractional-N concept, and data rate is programmable from 1.2-250 kBaud.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Wireless Transceivers | RF Receivers | RF Transmitters

Transceiver Module offers extended 802.15.4/ZigBee range.

info@productnews.com (ThomasNet News) — Mon, 19 Oct 2009 08:37:49 -0500

With range of up to 2 miles, MeshConnect(TM) Extended Range Module (ZICM2410P2) enables LED lighting control and applications in RF-noisy environments. Solution integrates built-in voice CODEC processor, while +123.5 dB link budget enables optimal data rates to be maintained for extended distances. Intended for 802.15.4/ZigBee applications, product consumes less than 1 µA during sleep mode power consumption, promoting battery life.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Wireless Transceivers

Full-Duplex IF Transceiver offers optimized integration.

info@productnews.com (ThomasNet News) — Fri, 16 Oct 2009 08:40:27 -0500

Supplied in 14 x 14 mm QFP, TRF2443 low-noise intermediate frequency (IF) transceiver features cross-polarization interference cancellation support. Integration of 15+ functional blocks, along with output third order intercept point of 29.5 dBm and receiver noise figure of 4.3 dB, ensures linearity and sensitivity suited for wireless infrastructure backhaul and point-to-point microwave end equipment. Other features include programmable baseband low-pass filters and Tx/Rx synthesizers.

This story is related to the following:
Communication Systems and Equipment
Computer Hardware and Peripherals

Search for suppliers of: Wireless Transceivers | Transceivers

RF Transceiver has dual receivers to minimize channel fading.

info@productnews.com (ThomasNet News) — Thu, 15 Oct 2009 08:34:28 -0500

MAX2839AS WiMAX(TM) MIMO RF transceiver includes two 2.3-2.7 GHz receivers that feature 2.3 dB noise, -81 dBm sensitivity for 64 QAM signal at 5 MHz channel bandwidth, and 95 dB gain control range digitally controlled in 1 dB steps. Transmitter has 62 dB gain control range controlled in 1 dB steps, 0 dBm linear output with 64-QAM signal, and greater than -45 dBc of sideband suppression. Contained in 3.5 x 5.1 mm package, product operates from 2.7-3.6 V supply.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Wireless Transceivers | RF Transceivers

Embedded Wireless Module offers HSPA frequency support.

info@productnews.com (ThomasNet News) — Tue, 13 Oct 2009 08:32:16 -0500

Designed for HSPA networks, MC8795V offers 850, 900, 1,900, and 2,100 MHz frequency support as well as respective downlink and uplink data speeds of 7.2 Mbps and 5.76 Mbps. Antenna diversity promotes fringe performance on global HSPA networks, while software, applications, and tools; installation and activation wizards; and hardware drivers facilitate certification and commercialization process. RoHS-compliant solution, also GPS-capable, supports simultaneous voice and data usage.

This story is related to the following:
Computer Hardware and Peripherals
Communication Systems and Equipment

Search for suppliers of: Data Modules | Wireless Modems

Bluetooth® RF-Transceiver speeds data exchange between I/O nodes.

info@productnews.com (ThomasNet News) — Mon, 05 Oct 2009 08:27:00 -0500

Configured via WAGO-I/O-CHECK 3 software, 750-644 provides bidirectional, wireless communication between I/O nodes. One 750-644 master can communicate with up to 7 slaves on PAN/piconet via Bluetooth® 2.0+EDR radio technology, and slave-to-slave data transmission is possible indirectly through master. Within 10 ms, it exchanges data up to 1,000 m (line-of-sight) or 100 m (within buildings). Frequency hopping and adaptive transmitting power technologies provide robust communications.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Wireless Transceivers | RF Transceivers | Bluetooth Modules

Mobile Radio operates in VHF frequency band.

info@productnews.com (ThomasNet News) — Wed, 23 Sep 2009 08:35:04 -0500

KNG M150 operates in VHF frequency band (136-174 MHz) and addresses requirements of government and public safety professionals. Features include touch-screen operation, class-A performance, durable construction. M150 is also available in 100 W high-power configuration that extends the radio's reach with additional signal strength. It is also upgradeable to P25 Trunking.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Two-Way Radios | Radios

Wireless Transceiver Module is protocol-independent.

info@productnews.com (ThomasNet News) — Fri, 18 Sep 2009 08:32:07 -0500

Operating at 1,550 Nm wavelength, 10G-XNPK-ER plug-play transceiver module has typical transmission distance of up to 40 km. Transceiver can be used in wireless communication devices such as cellular telephones, cordless telephone sets, handheld two-way radios, mobile two-way radios, and fiber optical systems.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Wireless Transceivers

RF Transceiver supports 3GPP WCDMA/EGPRS wireless phones.

info@productnews.com (ThomasNet News) — Fri, 18 Sep 2009 08:32:03 -0500

Featuring 6 outputs that drive power amplifier directly, multi-mode Model MB86L01A eliminates 3G TX and RX inter-stage SAW filters and low noise amplifiers. Programming model controls radio using open standard 3G DigRF/MIPI digital interface. Optimized for compressed mode operation, transceiver features quad-band GSM/EDGE and up to 4 WCDMA bands in single-phone configuration. Receiver incorporates anti-aliasing filters, digital channel filters, digital gain control, and high dynamic range ADCs.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Wireless Transceivers | RF Transceivers

WiMAX Base Station suits carrier/smart grid networks.

info@productnews.com (ThomasNet News) — Thu, 17 Sep 2009 08:29:00 -0500

RedMAX 4C SC-100e incorporates IEEE 802.16e-2005 technology and operates in 1.8, 2.5, and 3.5 GHz spectrum bands. Based on PHY and MAC, it supports up to 3 high-power radios, using 1, 2, or 3 frequencies, within single 1U base station unit. System includes GPS and multisector support, simplifying network planning, and also supports distributed coverage for indoor and outdoor deployments. Optical interface and external AC/DC converter are also included.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Wireless Transmitters | Wireless Modems

Wireless Interface Module is designed for motor control.

info@productnews.com (ThomasNet News) — Tue, 15 Sep 2009 08:31:10 -0500

Providing option to run mesh networks with ZigBee protocol on top of IEEE 802.15.4 radio technology, MAC00-FZ4 interface module offers capability to address large number of motors from one master computer. Module can be used with all JVL integrated servo motors MAC050-140, MAC400, and MAC800 from 50-750 W.

This story is related to the following:
Communication Systems and Equipment
Computer Hardware and Peripherals
Test and Measuring Instruments

Search for suppliers of: Wireless Communication Systems | Interface Modules

Packet Node features synchronization for all-IP networks.

info@productnews.com (ThomasNet News) — Fri, 04 Sep 2009 08:26:11 -0500

Eclipse(TM) Packet Node IP wireless backhaul platform includes Distributed Sync(TM), which enables migration of existing TDM infrastructure to all-IP transport network. Supported by plug-in network sync module, synchronization feature offers primary reference clock traceable for 2.048/1.544 MHz clock output at base station over multihop, nodal backhaul network. Node has link speeds up to 2 Gbps, adaptive coding and modulation with XPIC, and multiservice support for TDM and Ethernet/IP traffic.

This story is related to the following:
Computer Hardware and Peripherals
Communication Systems and Equipment

Search for suppliers of: Network Devices | Wireless Communication Systems

First Responder Radio has trunked and conventional features.

info@productnews.com (ThomasNet News) — Tue, 25 Aug 2009 08:27:32 -0500

Hybrid IP25(TM) wide area conventional infrastructure system enables first responders to roam between trunked and conventional systems. Seamless roaming and mobility eliminate need for dispatchers to manually patch calls between 2 systems. Project 25-compliant solution utilizes fully distributed, switchless architecture that promotes system scalability and interoperability while also eliminating single point of failure.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Radio Systems | Two-Way Radios | Radios

Satellite Modem features dynamic bandwidth allocation.

info@productnews.com (ThomasNet News) — Tue, 18 Aug 2009 08:43:58 -0500

Suited for broadcaster's SNG vehicles, FlyAways, or transportable units, 1HU SkyWAN® IDU 1070 includes Turbo-Φ-Coding, IP Routing, and true full mesh capability. Support of QPSK/8PSK modulation schemes with wide range of code rates optimizes bandwidth efficiency for any kind of network topologies. Built-in, multi-port Ethernet switch allows plug in communications devices for VoIP, video-conferencing, and all types of IP data applications.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Wireless Modems

Multi-Band Two-Way Radios feature integrated GPS.

info@productnews.com (ThomasNet News) — Mon, 17 Aug 2009 08:30:12 -0500

Designed to communicate with current and future P25 networks, APX(TM) 7000 Radios operate in 700/800 MHz and VHF bands, and meet and exceed public safety specifications for mission critical communications by optimizing officer coordination, response time, and safety via access to real-time information. Applying science of High Velocity Human Factors, dual-sided portable radios provide first responders with loud and clear audio in compact rugged form factor.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Two-Way Radios

Short Range RF Transceivers suit smart grid applications.

info@productnews.com (ThomasNet News) — Fri, 14 Aug 2009 08:29:47 -0500

Designed for operation at io-homecontrol® channels of 868.25, 868.95, and 869.85 MHz in license-free ISM band, ADF7022 FSK/GFSK Transceiver performs complex tasks typically performed by microprocessor, such as media access, packet management/validation, and packet retrieval to and from data buffer memory. Model ADF7023, designed for operation in ISM bands at 433, 868, and 915 MHz, operates from 1.8-3.6 V and offers data rates in 2FSK/GFSK up to 250 kbps.

This story is related to the following:
Communication Systems and Equipment
Computer Hardware and Peripherals

Search for suppliers of: Transceivers | Wireless Transceivers | RF Transceivers

RF Transceivers advance design of small 4G base stations.

info@productnews.com (ThomasNet News) — Wed, 12 Aug 2009 08:29:54 -0500

Integrating 12-bit ADCs, DACs, RF-receive and RF-transmit signal chains, and on-chip frequency synthesizers, Models AD9356 and AD9357 support 2.3-2.7 GHz and 3.3-3.8 GHz ranges, respectively, covering existing WiMAX bands and channel bandwidths of 3.5, 4.375, 5, 7, 8.75 and 10 MHz. Signal-to-noise ratio provides support for picocells and microcells from +13 dBm to +36 dBm output power at antenna port, while smart-partitioning architecture supports autonomous AGC, TPC, and calibration routines.

This story is related to the following:
Computer Hardware and Peripherals
Communication Systems and Equipment

Search for suppliers of: RF Transceivers | Transceivers | Wireless Transceivers