ThomasNet Industrial Newsroom -

Coating offers corrosion protection to 1,500°F.

info@productnews.com (ThomasNet News) — Tue, 11 Aug 2009 08:30:47 -0500

Formulated using waterborne silicate binder system filled with blend of stainless steel and ceramic corrosion inhibiting pigments, Corr-Paint(TM) CP3015-SS is suited for coating carbon steel and cast iron heat exchangers, boiler components, and exhaust headers. Single part coating system is supplied in ready-to-use viscosity of 500-1,000 cP, is applied using conventional spray equipment, and dries to typical film thickness of 2-3 mils.

This story is related to the following:
Paints and Coatings

Search for suppliers of: High Temperature Coatings | Water Borne Coatings | Protective Coatings | Corrosion Resistant Coatings | Ceramic Coatings | Stainless Steel Coatings

High Temperature Coating protects exhaust headers.

info@productnews.com (ThomasNet News) — Tue, 20 Jan 2009 08:31:37 -0500

Black-pigmented, ceramic-filled Corr-Paint(TM) CP3015-BL inhibits oxidation of carbon steel and cast iron exhaust headers used in automotive, truck, and industrial applications to 1,500°F. Product is formulated using waterborne silicate binder system filled with blend of ceramic corrosion inhibiting pigments. Supplied in ready-to-use viscosity of 2,800-4,500 cp and solids of 51.5% by weight, coating is applied using spray equipment, drying to film thickness of 2-3 mils.

This story is related to the following:
Paints and Coatings

Search for suppliers of: Water Borne Coatings | Industrial Coatings | High Temperature Coatings | Corrosion Resistant Coatings | Ceramic Coatings | Automotive Component Coatings

Ceramic Conditioner helps optimize automotive fuel economy.

info@productnews.com (ThomasNet News) — Wed, 19 Nov 2008 07:42:44 -0500

Available in 10 ml syringes, CerMet-Auto(TM) minimizes friction in gas-powered engines. Microscopic ceramic particles are carried to engine's friction zones via engine oil, where they bond to metal surfaces, providing fuel economy benefits for approximately 60,000 miles of operation. Heat energy generated inside engine due to friction initiates ceramic coating process at atomic level, with full benefits being achieved after 2,000 miles of driving.

This story is related to the following:
Materials and Material Processing
Paints and Coatings

Search for suppliers of: Oil Additives | Ceramic Coatings

Water-Based Ceramic Coating is odorless and contains no VOC.

info@productnews.com (ThomasNet News) — Wed, 15 Oct 2008 07:29:21 -0500

Designed to electrically insulate high temperature ceramic resistors, green-pigmented Cerama-Diptm 538N-GREEN inorganic-ceramic coating can be used for applications up to 2,600°F. It offers volume resistivity of 109 ohm-cm and dielectric strength of 225 V/mil at room temperature. Curing is achieved by air-drying at room temperature for 1-2 hr, then step curing for 1-2 hr at 200 and 350°F, respectively. Coating comes in standard pint, quart, gallon, and 5 gal containers.

This story is related to the following:
Paints and Coatings
Material Handling and Storage Sponsored by: Reid Supply - FREE CAD Drawings of Tens-of-Thousands of Parts!
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!

Search for suppliers of: Environmental Coatings | Coating Systems | Ceramic Coatings | Electrical Insulation Coatings | High Temperature Coatings | Water Based Coatings

Silver Coating is used to reduce glare in halogen lamps.

info@productnews.com (ThomasNet News) — Tue, 02 Sep 2008 07:41:35 -0500

With low expansion, ceramic-metallic formulation that bonds well to glass and quartz halogen lamps, Quartz-Coat(TM) 845-Silver suits automotive, dental, aircraft, stadium, and fire safety industries. Product is water-based, odorless inorganic system that is silver in appearance and can absorb and evenly diffuse light at high temperatures of up to 2,000°F. It features viscosity range of 400-700 cps, solids content by volume of 42.0%, and dry film thickness of less than 1.0 mil.

This story is related to the following:
Paints and Coatings

Search for suppliers of: Metallic Coatings | Ceramic Coatings | Silver Coatings | Water Based Coatings

Coating protects steel and fiberglass boat bottoms.

info@productnews.com (ThomasNet News) — Tue, 30 Oct 2007 07:48:23 -0500

Designed for marine vessel hulls, Ship and Boat Bottom Coating is polymer/ceramic-based and contains no TBT or VOCs. Powder coating has evenly dispersed active copper oxide and silver ions in polymer matrix that is fully melted when applied with thermal spray process. If there should be break or tear in coating, nylon modified fuse bond epoxy between hull and coating maintains integrity. Active ingredients are strongly held and always available in coating, minimizing ablating.

This story is related to the following:
Paints and Coatings

Search for suppliers of: Protective Coatings | Powder Coatings | Polymer Coatings | Marine Coatings | Ceramic Coatings

High-Temperature Adhesive is suited for use in IR heaters.

info@productnews.com (ThomasNet News) — Fri, 17 Aug 2007 07:45:32 -0500

Pyro-Paint(TM) 634-AS-1 is used to bond, coat, and seal refractory fiberboard used in construction of IR heaters and molten metal handling components in foundry applications to 2,300°F. Applied by brush, roller, or spray equipment, this alumina-silica based, fiber-reinforced, ceramic coating system is resistant to wetting by non-ferrous molten metals and adheres to refractory fiberboard, graphite, as well as ceramic cloth and paper. Water-based formulation contains no VOCs.

This story is related to the following:
Adhesives and Sealants Sponsored by: Henkel Corp. - World Leader in Adhesives, Sealants & Surface Treatments
Paints and Coatings

Search for suppliers of: Ceramic Coatings | High Temperature Adhesives

Coating System suits high temperature headers.

info@productnews.com (ThomasNet News) — Tue, 07 Aug 2007 07:43:50 -0500

Available in pint, quart, gal, and 5 gal pails, Corr-Paint(TM) CP3015-AL, ultra-high temperature coating is used to inhibit oxidation of carbon steel and cast iron exhaust headers used in automotive, truck, and industrial applications to 1400°F. It is formulated with advanced, waterborne silicate binder system filled with blend of aluminum and ceramic corrosion inhibiting pigments. Product is supplied in ready to use viscosity of 250-450 Cp and solids of 71.0% by weight.

This story is related to the following:
Material Handling and Storage Sponsored by: Reid Supply - FREE CAD Drawings of Tens-of-Thousands of Parts!
Paints and Coatings

Search for suppliers of: High Temperature Coatings | Coating Systems | Aluminum Coatings | Ceramic Coatings

Black-Body Coating suits high-temperature applications.

info@productnews.com (ThomasNet News) — Thu, 27 Apr 2006 06:32:24 -0500

HiE-Coat(TM) 840-C helps improve thermal efficiency of ceramic and refractory insulated combustion and exhaust pipes as well as oven and furnace walls to 2,500°F. Demonstrating emissivity greater than 0.90, this jet-black, water-based ceramic coating will absorb and re-radiate IR energy. Cured in operation or by heating for 1-2 hr @ 200°F, environmentally friendly product is odorless and water-soluble, does not contain VOCs, and will not outgas upon curing or during operation.

This story is related to the following:
Paints and Coatings

Search for suppliers of: Ceramic Coatings

Coating System electrically insulates ceramic resistors.

info@productnews.com (ThomasNet News) — Wed, 28 Sep 2005 07:13:25 -0500

As single-part, water-based, inorganic-ceramic coating system, Cerama-Dip(TM) 538N electrically insulates high-power ceramic resistors in applications to 2,600°F. Odorless, non-outgassing product contains no VOCs and features volume resistivity of 109 ohm-cm and dielectric strength of 225 V/mil at room temperature. Curing is accomplished by air-drying at room temperature for 1-2 hr then step curing for 1 or 2 hr at 200°F and 350°F, respectively.

This story is related to the following:
Electrical Equipment and Systems Sponsored by: Globtek Inc. - Your Power Partner...For Over 20 Years!
Paints and Coatings

Search for suppliers of: Electrical Insulation Coatings | Ceramic Coatings | Resistor Coatings | High Temperature Coatings

Refractory Coating withstands temperatures to 3,200°C.

info@productnews.com (ThomasNet News) — Tue, 17 May 2005 07:52:15 -0500

Pyro-Paintâ"¢ 634-AL provides 2-part, 99% alumina filled, ceramic coating system used to bond, coat, and seal refractory fiber boards and other shapes. Material helps prevent wear and oxidation of refractory components and increases heat reflectivity. Resistant to wetting by most molten metals, product has solids content of 76.8% by weight, 66.0% by volume, and viscosity range of 5,000â�"6,000 cps. Water-based formulation has no VOCs and dries within 2 hr at 200°F.

This story is related to the following:
Paints and Coatings

Search for suppliers of: Ceramic Coatings | Refractory Coatings

Ceramic-Based Coating seals thermal spray coatings.

info@productnews.com (ThomasNet News) — Mon, 14 Mar 2005 08:10:17 -0500

Ceramacoatâ"¢ 503-VFG-C high-temperature sealant fills micro-porosity in corrosion protective, thermal spray coatings. It is formulated as single part, water-dispersible, alumina-filled system. Inert, chemically-resistant, inorganic material will not outgas or decompose in high-temperature, corrosive applications up to 3,200°F. Product is applied using sponge brush or pneumatic spray equipment. Full cure is achieved after exposure for 1-2 hr at 700°F.

This story is related to the following:
Paints and Coatings

Search for suppliers of: Ceramic Coatings | Chemical Resistant Coatings

Ceramic-Filled Epoxy protects parts from corrosion/wear.

info@productnews.com (ThomasNet News) — Wed, 21 Jan 2004 14:47:47 -0500

Ceramic Coat® epoxy system is formulated to repair, rebuild, and protect surfaces subject to corrosion or wear, negating need for replacement parts. After reframing, damaged blades can be rebuilt to original specifications with trowelable CT 3000® and then protected with brushable Ceramic Coat 4000®. Applications include pump casings, impeller blades, suction plates, gate and butterfly valves, water boxes, tube sheets, and heat exchangers.

This story is related to the following:
Adhesives and Sealants Sponsored by: Henkel Corp. - World Leader in Adhesives, Sealants & Surface Treatments
Paints and Coatings

Search for suppliers of: Repair Epoxies

Refractory Coating withstands temperatures to 2,300°F.

info@productnews.com (ThomasNet News) — Wed, 26 Nov 2003 07:44:06 -0500

Pyro-Paintâ"¢ 634-AS alumina-silica-filled, fiber-reinforced, ceramic coating bonds, coats, and seals graphite and refractory materials used in molten metal fluid handling components. It also coats and insulates graphite impellers, preventing oxidation and corrosion of graphite at melt line. With 400â�"700 cps viscosity range, it is resistant to wetting by non-ferrous molten metals, environmentally friendly, water-based, and contains no VOCs.

This story is related to the following:
Paints and Coatings

Adhesive and Coating withstands temperatures to 2,400°F.

info@productnews.com (ThomasNet News) — Fri, 03 Oct 2003 08:11:53 -0500

Ceramacoatâ"¢ 512N high-temperature adhesive and ceramic coating system is used in assembly of ceramic, metal, and plastic electrical components and as coating of high temperature structures requiring corrosion protection. Single part, water-based, silica-filled system offers volume resistivity of 10<sup>9</sup> ohm-cm and dielectric strength of 250 V/mil at room temperature. Odorless product contains no VOCs, and no outgassing will occur upon cure or during operation.

This story is related to the following:
Adhesives and Sealants Sponsored by: Henkel Corp. - World Leader in Adhesives, Sealants & Surface Treatments
Paints and Coatings

Search for suppliers of: High Temperature Adhesives | Ceramic Coatings

Blacktop Coating System absorbs halogen lamp intensity.

info@productnews.com (ThomasNet News) — Fri, 30 Aug 2002 08:28:58 -0500

Quartz-Coatâ"¢ 845-S high temperature, sprayable, blacktop coating system has ceramic-metallic formulation that bonds to glass and quartz lighting fixtures. Single-component formulation is aqueous-based and inorganic, pigmented with deep black, temperature-stable filler. Stable in applications to 2000°F, Quartz-Coat 845-S offers viscosity range of 400â�"700 cps and has 42.0% solids content by volume. Post-cure coating is moisture resistant and non-outgassing.

This story is related to the following:
Paints and Coatings

Search for suppliers of: Ceramic Coatings

Ceramic Coating seals thermal spray coatings.

info@productnews.com (ThomasNet News) — Tue, 23 Jul 2002 08:57:18 -0500

Ceramacoatâ"¢ 503-VFG-S ceramic-based sealant is formulated as single part, water-dispersible, alumina-filled system. Inert, chemically resistant, inorganic material does not outgas or decompose in high temperature corrosive applications to 3200°F. Applied using sponge brush or pneumatic spray equipment, full cure is achieved after exposure for 1-2 hours at 700°F. It sinters and strengthens as exposed to temperatures above 1000°F.

This story is related to the following:
Adhesives and Sealants Sponsored by: Henkel Corp. - World Leader in Adhesives, Sealants & Surface Treatments
Paints and Coatings

Search for suppliers of: Ceramic Coatings | Sealants

High-Temperature Paint provides corrosion protection.

info@productnews.com (ThomasNet News) — Tue, 07 May 2002 08:07:10 -0500

Single-part, aluminum-rich Corr-Paint(TM) CP4010 ceramic-silicone based coating protects steel components and structures for applications to 1200 deg F. It is resistant to acids, bases, and solvents, and provides thermal-shock, salt-spray, and UV resistance. Water-dispersible coating dries at room temperature and cures fully during operation at temperatures above 450 deg F. Non-flammable, low VOC formulation has viscosity of 700 to 1400 cps.

This story is related to the following:
Paints and Coatings

Search for suppliers of: Ceramic Coatings

Coatings protect metal and refractory surfaces.

info@productnews.com (ThomasNet News) — Fri, 11 Jan 2002 08:49:50 -0500

Corr-Paintâ"¢ coatings are designed for use from 200° to 2500° F. CP20XX Series epoxy and urethane based coatings produce corrosion and wear resistant barriers to 500°F. CP30XX inorganic-ceramic, aqueous-based coatings resist thermal shock and oxidation to 1500°F. CP40XX silicone-based coatings are formulated using VOC-compliant, water-dispersible silicon resin. CP5000 2-part, water-based, inorganic, zinc-rich primer resists immersion, impact, and abrasion.

This story is related to the following:
Chemical Processing and Waste Management
Paints and Coatings

Search for suppliers of: Urethane Coatings | Water Based Coatings | Epoxy Coatings | Ceramic Coatings

Ceramic Coating protects metals and alloys.

info@productnews.com (ThomasNet News) — Thu, 08 Nov 2001 16:20:27 -0500

Microplasmic Process creates thick ceramic coating that resists wear, heat and aqueous corrosion, and is an electrical insulator. Light aluminum, magnesium, titanium or other alloy parts that are coated with process can replace heavier steel or composite materials. Other reactive metals, such as zirconium, vanadium and tantalum, can also be coated. Any coating thickness can be achieved with aluminum, magnesium, titanium and zirconium alloys.

This story is related to the following:
Paints and Coatings