ThomasNet Industrial Newsroom -

Fiber Optic Sensors feature dual 4-digit display.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 08 Jun 2006 08:11:06 -0500

Available with NPN or PNP outputs, Accu-Vue(TM) Fiber Optic Amplifiers incorporate one-touch auto-teach, and built-in timer functions ranging from 250 µsec to 20 sec. Sensor features auto power control to maintain constant light emission level over life of sensor and adjustable response times of 50 µsec. Applications include parts presence, label detection, error proofing, and thread detection.

This story is related to the following:
Optics and Photonics Sponsored by: Keyence Corporation of America - The Source for Digital Microscopy Solutions
Sensors, Monitors and Transducers Sponsored by: Keyence Corporation of America - The Internet Resource for Sensor Solutions
Communication Systems and Equipment

Search for suppliers of: Fiber Optic Sensors | Fiber Optic Amplifiers

Amplifier Module measures only 7.5 mm thick.

info@productnews.com (ThomasNet Industrial Newsroom) — Mon, 15 May 2006 08:16:54 -0500

Ultra-thin PureGain 400 erbium doped fiber amplifier module is designed to work within stringent space constraints found in transponder and line card applications. It can be used in pre-amp configuration, which enables high receiver sensitivity without trans-impedance amplifier, or booster configuration, which enables high launch power in advanced transmitter designs. Utilizing standard optical components, amplifier is compatible with Telcordia requirements.

This story is related to the following:
Optics and Photonics Sponsored by: Keyence Corporation of America - The Source for Digital Microscopy Solutions
Communication Systems and Equipment

Search for suppliers of: Optical Amplifiers | Fiber Optic Amplifiers

Fiber Optic Amplifiers permit stacking in large numbers.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 01 Feb 2006 05:43:17 -0500

DIN rail mounted Series 3060 features housing width of 10 mm, switching frequency of 1.5 kHz, and sensing range of 0-200 mm, depending on optical fibers used. Using 12-turn potentiometer with illuminated scale, operating distance can be adjusted between 20 and 200 mm. Switching output can be set to either light- or dark-ON directly on device. Available with both red and blue light, IP64-rated units are largely insensitive to environmental influences.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Fiber Optic Amplifiers

Fiber Optic Amplifiers feature push-button teach mode.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 14 Oct 2004 07:44:07 -0500

Available in NPN and PNP models, SU17 Series includes digital display that indicates incoming light level, adjustment steps, and scanning conditions. It offers 3 sensitivity settings, built-in auto-tuning, and 10 mm profile. DIN rail-mount amplifiers offer functionality from target detection to contrast sensing. Other features include mutual interference protection, tool-less attachment, and built-in timer.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Fiber Optic Amplifiers

Fiber Optic Amplifier comes in compact package.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 13 Jul 2004 07:36:12 -0500

DIN rail-mountable SU16 Series includes high power/high sensitivity models, or ultra-fast models with up to 8 kHz switching frequency. Housed in slim 10 mm profile package, series' sensitivity can be fine-tuned via multi-turn potentiometer. Features include self-diagnostic LEDs and weak signal outputs, mutual interference protection, and tool-less fiber attachment. Scanning ranges are offered to 6 m, and response times are as fast as 50 µsec.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Fiber Optic Amplifiers

Sources and Amplifiers suit laboratory applications.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 26 Sep 2003 08:14:43 -0500

Leveraging diode-pumped erbium doped fiber technology, Broadband ASE (amplified spontaneous emission) sources and EDFAs (erbium doped fiber amplifiers) are packaged for test and measurement of photonics components in 1550 nm spectral region. Self-contained BBS-410 and BBS-430 sources generate broadband output as high as 25 mW. Fully-integrated FPA-410 and FPA-415 EDFAs feature signal gains of greater than 33 dB across C-band (1520-1560 nm).

This story is related to the following:
Communication Systems and Equipment
Electronic Components and Devices Sponsored by: Lumera Corporation -

Search for suppliers of: Fiber Optic Amplifiers | Signal Sources

Amplifier and Transponder simplify network installation.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 29 Apr 2003 07:36:19 -0500

Model A1070 Erbium Doped Fiber Amplifier consists of variable gain line amplifier with up to 25 db of gain and automatic transient suppression, which minimizes transmission penalties as channels are added/dropped in network. Supporting up to 40 channels at full gain, unit is managed through local serial port, Telnet, or SNMP. Optical transponder A1010 offers 640 km Dense Wavelength Division Multiplexing (DWDM) laser option. Each model occupies one rack unit in 19 in. chassis.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Transponders | Fiber Optic Amplifiers

Amplifier provides signal gains of 35 dBm.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 01 Apr 2003 08:02:51 -0500

Single-Channel C-Band Erbium Doped Fiber Amplifier comes as cooled or coolerless gain block with integrated control electronics that includes laser and TEC driver circuit with alarms and monitors. Amplifier is capable of signal gains up to 35 dBm with noise of less than 4.5 dB and total output power of +10 dBm. Assembly, electrical interface, and included software bundle measures 90 x 70 x 12 mm.

This story is related to the following:
Communication Systems and Equipment

Search for suppliers of: Fiber Optic Amplifiers

Fiberoptic Sensor Amplifier has dual digital display.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 12 Apr 2002 07:37:48 -0500

FS-V20 offers 50 micro second response time, detecting up to 10,000 targets per second. Four-element LED light source provides detection distances up to 1800 mm, plus stable operation in harsh environments. Six user selectable light power modes, viewable on display, offer 6 levels of detection distances. High resolution mode digitizes received light to 16 bits or 65,520 levels. FS-V20 supports 1-line wire connection system.

This story is related to the following:
Communication Systems and Equipment
Optics and Photonics Sponsored by: Keyence Corporation of America - The Source for Digital Microscopy Solutions
Sensors, Monitors and Transducers Sponsored by: Keyence Corporation of America - The Internet Resource for Sensor Solutions

Search for suppliers of: Fiber Optic Sensors | Fiber Optic Amplifiers