ThomasNet Industrial Newsroom -

Heater and Furnace recycle used oils into free shop heat.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 28 Aug 2008 07:42:18 -0500

Rated for 250,000 BTU input, RA-250 standard unit space heater and RAD-250 ductable furnace offer full swing-out door, large service panels, and maintenance/service shelf to facilitate combustion chamber and heat exchanger access. Along with oil-preheating system, backflow ash/draft sensor, and operation hour meter, units incorporate air atomizing burner, on-board air compressor, positive displacement fuel metering pump, and automatic thermostat-controlled operation.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Space Heaters | Fuel Oil Heaters | Industrial Oil Fired Furnaces

Plenum-Rated Heaters offer blower delay feature.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 04 Mar 2008 07:41:34 -0500

Designed for concealed and plenum space applications, BerkoÂ® and QMarkÂ® PRH Series offer multiple heat rise selections, with heating ratings from 3-15 kW. Max outlet air temperature is 200Â°F at static pressure of 0.2 in. Available with voltages of 208, 240, 277, and 480 V, heaters feature steel-finned heating elements, acoustic fiberglass insulation, and forward-curved centrifugal blower. Small unit is 24 x 19Â½ x 12Â½ in., while large cabinet measures 35 3/8 x 18 x 18 in.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Duct Heaters | Confined Space Heaters

Filter Housing Heaters suit biopharmaceutical applications.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 08 Feb 2008 07:56:11 -0500

Series 48 filter housing heaters are designed for biopharmaceutical processes requiring advanced thermal control of material viscosities and vapor condensation. Integrated temperature controller accommodates higher temperatures for stainless steel housings and lower temperatures for single use housings. Controller is protected by NEMA 4X enclosure, and features digital display for adjusting temperature set points, high/low temperature alerts, and high temperature safety limits.

This story is related to the following:
HVAC

Search for suppliers of: Enclosure Heaters

Electric IR Spot Heater warms commercial decks and patios.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 06 Feb 2008 07:55:51 -0500

Designed for commercial and residential deck and patio applications, HZE X5C 015 series has curved back design and compound reflective IRLens(TM) that focuses IR energy into central beam. Unit requires 1,500 W of electric power at 120-277 V and will raise temperature of people and objects in 14 ftÂ² area by 15Â° or more from 8 ft away. Heater can be wall-, ceiling- or post-mounted.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Electric Infrared Heaters | Patio Heaters | Infrared Heaters

Nozzle Heater is suited for hot runner systems.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 11 Jan 2008 07:30:47 -0500

THERMASLEEVE(TM) Hot Runner Nozzle Heater comes with rapid thermal response that allows heat to be created precisely where it is needed. Designed to have intimate contact with surface of nozzle which optimizes heat transfer, it features laser structuring to create customized temperature profile. Self-clamping electric heater can be installed and removed from nozzle with custom installation and removal tool, and accommodates thermocouple secured to external body of heater.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Nozzle Heaters

Truck Cab is designed for cold storage warehousing.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 02 Nov 2007 07:42:56 -0500

ThermoAssist(TM) and ThermoAssist+(TM) offer cold storage companies ergonomic solution that provides operator comfort and safety, reduced fatigue, and fewer warm-up breaks. Suited for reach trucks dedicated to freezer environments, ThermoAssist(TM) includes pad heaters for back and arm, console enclosure, and mast air deflector that redirects airflow away from operator. ThermoAssist+(TM) provides warm air to multi-task handle and steer tiller through adjustable vents.

This story is related to the following:
HVAC

Search for suppliers of: Cargo Truck Heaters | Heating Systems

Zero Clearance Heaters install in concealed spaces.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 05 Oct 2007 07:57:42 -0500

Rated at 2,500 W, Models PHFP25 and CHPR25 are designed for installation in concealed spaces including crawl spaces, plenum spaces, and areas between finished ceilings and drop ceilings. They include thermostat range of 40-90Â°F; enclosed, permanently lubricated fan motors; and fan-delay feature, which eliminates cold-air circulation at start-up. Measuring 14 x 12 in., heaters are crafted from 18 ga steel and protected from corrosion by gray, polyester powder-coat finish.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Light Commercial & Residential Heaters | Confined Space Heaters

Process Air Heater heats nitrogen/inert gas up to 1,400Â°F.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 03 Jul 2007 07:39:17 -0500

Featuring digital display temperature control, SKORPION(TM) Process Air Heater provides full closed-loop PID temperature regulation with Â±2Â° accuracy. Device includes serpentine coil design for maximum heat transfer efficiency, blower motor, air intake, and intelligent over-temperature sensing system. All-metal air source ensures operation in dusty environments, and unit also features adjustable air damper for flow control.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Process Heaters | Air Heaters

Focus Pre-Heater accelerates lead-free rework.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 06 Apr 2007 07:45:36 -0500

Pre-heater convection tool, PCT-100, can be used with or without board holder to perform hand assembly or rework tasks on SMT or through-hole assemblies. Optional dedicated board holder is available, and 10 cfm fan fitted to unit promotes heating and cooling. Designed to promote process control, product uses convection air heating to optimize responsiveness and avoid temperature overshoot. Pre-heater can be used with SnPb solders as well as lead-free ones.

This story is related to the following:
HVAC
Machinery and Machining Tools Sponsored by: Omni Metal Finishing, Inc. - Finishing with Excellence
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Convection Heaters | Air Heaters | Printed Circuit Board (PCB) Assembly Equipment

Windshield Fluid Heater promotes vehicle energy effficiency.

info@productnews.com (ThomasNet Industrial Newsroom) — Mon, 05 Feb 2007 07:04:48 -0500

Combining anodized aluminum substrate with thick film resistive element, AnothermÂ® Windscreen Module provides vehicle designer with instant heating technology for automotive and transportation windshield washer applications. Tubular instant fluid heater module does not use any power until heated fluid is required, resulting in energy savings up to 95%. Packaged for underhood environments, it evenly heats fluid in 5 sec without boiling away additives such as methanol or ethanol.

This story is related to the following:
HVAC

Search for suppliers of: Automotive Heaters

Garage Heater suits high humidity and dusty areas.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 30 Dec 2005 07:08:43 -0500

With BTU inputs of 30,000, 45,000, 60,000, and 75,000, Hot DawgÂ® Model HDS draws combustion air from outside, optimizing seasonal heating efficiency and minimizing concerns about dusty, dirty, or humid applications. Operating with natural gas or propane, unit features tubular heat-exchanger design and is certified for residential and commercial use. Applications include greenhouses, tool sheds, wet garages, and hostile environments.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Garage Heaters | Propane Heaters | Gas Heaters

Blower Heater suits harsh environments.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 01 Apr 2005 09:53:43 -0500

Corrosion-resistant Model HD3D provides comfort heating and freeze prevention in harsh, corrosive, dirty, and wet environments. With stainless steel brackets, hose-down unit can be directly mounted to wall or ceiling. NEMA 4X control box is located on front of heater. Wiring connector provides watertight seal in event of replacement of motor, limit control, or elements. Heater is suited for wastewater treatment plants, steel mills, ships, car washes, and foundries.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Industrial Heaters | Hazardous Area Heaters | Air Heaters | Heating Blowers

Make-Up Air Unit suits institutional applications.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 17 Mar 2005 07:39:51 -0500

Model IG-HV features power-vented, 80% efficient, indirect gas-fired furnace with post-purge cycle. It provides airflow volumes to 7,000 cfm with heating capacities up to 400,000 btu/hr input. Unit is supplied with double width, double inlet, forward curved blowers tested to AMCA standards. It offers 3 heating and ventilation options plus 8 economizer and mixing box options, and can be supplied with 8:1 turndown furnace control.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Indirect Fired Heaters | Air Heaters | Ventilators

Heater/Cooler protects electronics from extreme temps.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 15 Feb 2005 07:53:16 -0500

Available in 3 sizes to fit smallâ�"medium sized enclosures, ADALET Heater/Cooler protects electrical and electronic components from degradation due to high or low temperatures. It may be used to heat or cool full time, but can be adjusted to switch from heater to cooler using added thermostat controller. Featuring stainless steel design, unit is built to UL NEMA 4X, 12, and 13 standards; has few moving parts; and does not require use of CFCs.

This story is related to the following:
HVAC

Search for suppliers of: Enclosure Heaters | Electric Equipment Coolers | Electronic Equipment Coolers

Heater Line offers hydronic, kickspace, and aesthetic units.

info@productnews.com (ThomasNet Industrial Newsroom) — Thu, 08 Jul 2004 07:33:10 -0500

Horizontal and vertical hydronic heaters, Series BH and BV, are made with reinforced 18- and 16-gauge cold rolled steel, respectively. Both provide quiet operation and are treated for corrosion-resistance with epoxy-based powder coating. Series BKS kickspace heater uses cross flow fan technology and includes epoxy-based powder coated finish. Panelray features flat tube steel design with broad radiating surfaces. Panelray Towel Warmer heats bathrooms, kitchens, or anywhere decorative heating is desired.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Towel Warmers | Hydronic Heaters | Kickspace Heaters

Space Heater suits commercial and industrial buildings.

info@productnews.com (ThomasNet Industrial Newsroom) — Mon, 22 Dec 2003 07:42:41 -0500

S-Series Heater features patented gas burner design and Blow-Thru construction that delivers 160Â°F max temperature rise. Thru-wall mounting option does not take up floor or warehouse racking space.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Electric Unit Heater ranges in size from 3-10 kW.

info@productnews.com (ThomasNet Industrial Newsroom) — Fri, 18 Jul 2003 00:00:00 -0500

Series UHI comes with built-in controls and can be wall or ceiling mounted. Standard voltages include 208, 240, 277, and 480 in single and 3-phase. Cabinets are heavy gauge galvanized steel and tubular elements are 304 SS. Individually adjustable louvers direct airflow where needed. Single point, line voltage connection enables heater, fan, and controls to be connected to same branch circuit. Built-in, automatic reset thermal cutout provides overtemperature protection.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Air Heaters | Unit Heaters | Industrial Heaters

Heating System provides space heating for warehouses.

info@productnews.com (ThomasNet Industrial Newsroom) — Tue, 29 Oct 2002 07:42:01 -0500

GreenHeat System uses direct gas-fired burner designed and ETL listed for 140Â°F temperature rise. It includes discharge diffuser to evenly distribute high temperature air for consistent space heating. Louvers, roof fans and propeller fans are available to complete package.

This story is related to the following:
HVAC

Search for suppliers of: Warehouse Heaters

Electric Baseboard Heaters are CSA approved to UL standards.

info@productnews.com (ThomasNet Industrial Newsroom) — Mon, 28 Jan 2002 09:21:09 -0500

BAI/BASI Series architectural heaters provide large amounts of quiet heat where fan noise is distracting and unacceptable. Constructed of heavy gauge steel, units are available up to 4 kW. BII/BISI Industrial heaters are constructed of heavy gauge, painted steel with screw assembly for additional strength and are available up to 2.5 kW. BCI/BCSI commercial heaters feature aluminum cover with steel cabinetry and are available up to 2.5 kW.

This story is related to the following:
HVAC
Thermal and Heating Equipment Sponsored by: TEMPCO - Electric Heater Corporation

Search for suppliers of: Baseboard Heaters | Electric Heaters

Cabinet Heaters mount anywhere.

info@productnews.com (ThomasNet Industrial Newsroom) — Wed, 02 Jan 2002 13:37:37 -0500

Ranging from 2-24 kW, CUI Series heaters may be mounted on floor, wall or ceiling, or recessed into wall or ceiling. Standard voltages include 208, 240, 277 and 480, with other voltages available. Lengths range from 28-80 in., depending on kW and voltage. Extruded aluminum grille discourages tampering with finned, tubular heating element. Controls include built-in automatic reset thermal cutout for overtemperature protection and fan delay relay.

This story is related to the following:
HVAC

Search for suppliers of: Confined Space Heaters