'); document.write('Featuring SOLAR Sonic Compression technology, Model No. PI30000X delivers clean, reliable power from 12 V power source to variety of power equipment, electronics, and appliances. Temperature-activated fan control eliminates unnecessary draining of power source when in standby mode, and junction block connection is designed for use in hard-wire installations. Integrated display helps operators manage power demands, and remote switch optimizes positioning in fixed installations.'); document.write('

'); document.write('Model 9074 RJ45 A/B/OFFLINE Switch allows sharing of one RJ45 device among 2 others, or all to be switched to secure OFFLINE position to isolate all ports. This manually operated keylock switch requires no power and can be integrated as system component by utilizing DIN rail mounting bracket on rear panel. The M9074 switches all 8 leads of the RJ45 interface and is certified for category 5e compliance.'); document.write('

'); document.write('With continuous transition between boost and regulated buck mode, Model AS1337 is suited for single or dual cell applications. Unit offers adjustable output voltage from 2.5-5.0 V from input voltage of 0.65-4.5 V. From 2-cell battery with 1.8-3.6 V voltage range, Model AS1337 provides 200 mA of output current at 3 V. Operating from -40 to +85°C, converter offers efficiencies up to 97% and draws only 10 nA shutdown current, extending battery lifetime.'); document.write('

'); document.write('Capable of direct currents up to 500 A, POWER-GATE low voltage disconnects require no heat sinking or airflow. Programmable, autonomous solid state relays are designed as central point of connect or disconnect for DC accessories such as inverters, radios, and motors. With high voltage trip, low voltage trip, timing features, logic feedback, and external monitoring, devices are customizable for fleet and OEM applications.'); document.write('

'); document.write('Housed in 2.0 x 2.0 x 0.65 mm wafer-level package, Model MAX8649 achieves initial accuracy of ±0.5% at 1.27 V and total accuracy of better than ±2% over load, line, and temperature, allowing processors to run at max clock speed. Synchronous, fixed-frequency step-down converter operates from input supply as low as 2.5 V to support deep-discharge battery chemistries. I²C interface allows programming of output voltage between 750 mV and 1.38 V in 10 mV steps.'); document.write('

'); document.write('Along with 2-pole switching, J104 Series offers coil voltage choices from 3-48 Vdc. Fully sealed solution has bifurcated gold-clad crossbar contacts, 500k-cycle tested electrical life, and 100M-cycle mechanical life. Operating from -40 to +85°C, relay features dielectric strength of 1,500 Vrms min coil to contact and 1,000 Vrms min contact to contact. Insulation resistance is 100 M<font face=\'Symbol\'>W</font> min @ 500 Vdc, and shock resistance is 100 m/s2 for 11 ms.'); document.write('

'); document.write('Accepting up to 305 Vac, 100 Watt PIL100 Series includes constant current models with output from 350-4,200 mA and constant voltage models offering 12-105 Vdc outputs. Units are housed in rugged aluminum enclosure, which meets IP67 waterproof standards, making them suitable for harsh indoor or outdoor applications. Operating from -35 to +70°C, modules include overvoltage, overcurrent, over temperature, and short circuit protection.'); document.write('

'); document.write('Offered in variety of sizes and hole patterns, BURNDY® BusBars are suited for use as common ground point in data center, central office, or power system. They come with insulators, stainless steel mounting brackets, and assembly bolts. Customizable units include 12 and 24 in. undrilled models, which can be custom drilled in field. Two models from series can be mounted either vertically or horizontally to equipment rack used to support computer equipment.'); document.write('

'); document.write('Suited for high-density PCB packaging, low-profile Coin Cell Retainers are designed for lead free solder and traditional reflow processes. Units protect battery from shorting if inserted incorrectly, and allow user to stack two 20 mm cells on top of each other to achieve 6 V of power on same board. They are also suited for single cell 3-volt applications. Offering clearly marked polarity, rugged parts include solder tails that support visual inspection systems.'); document.write('

'); document.write('Measuring 10.90 x 4.80 x 4.80 mm, 160 Series offers current ratings from 500 mA to 5 A, with max inrush current withstand of 127 A²secs and interrupting rating of 50 A at 250 Vac. Time-lag surface mount fuse/clip assembly minimizes probability of fuse opening during momentary overloads, and makes field replacement of fuse possible. RoHS-compliant and Halogen-free, assembly is suited for LED lighting, power converters and adapters, and telecom equipment.'); document.write('

'); document.write('Housed in SOT953 package that measures 1.0 x 1.0 x 0.5 mm, 4-channel SP1004 Series provides ESD protection at maximum level of IEC61000-4-2 international standard (Level 4, ±8 kV contact discharge). Unit has 6 V reverse standoff voltage with low leakage of less than 0.1 µA at 5 V. It is suited for cell phones, smart phones, PDAs, MP3/PMP players, and portable navigation devices. With total capacitance of 5 pF, device is also usable for high-speed data lines and low-speed audio lines.'); document.write('

'); document.write('Supporting output voltage of 5.1 V, Model SPD-50 delivers up to 12 W output power and max DC/DC converting efficiency of 85% at full load, while Model SPD-12, supporting 12 V output voltage, delivers 12 W output power and max DC/DC converting efficiency of 89% at full load. Units are compliant with IEEE 802.3af power classification and support PSE Alternative A and B connections. Measuring 60 x 16.9 x 16 mm, modules include thermal shut off as well as short circuit and over current protection.'); document.write('

'); document.write('With expected lifetime up to 20 years, THINERGY(TM) MEC102 offers multiple capacity options up to 2.5 mAh and up to 10 mWh of energy, as well as discharge rate capability of 100 mA and 300 mW continuous. Battery features inorganic, solid state construction and total package thickness of 170 µm. Suited for micro-electronic applications such as remote/autonomously powered wireless sensors, security systems, remote controls, and memory, battery will not overheat, burn, leak, or outgas.'); document.write('

'); document.write('Available in detect or single- or double-action tactile feedback versions, K6 and K12 series target automotive, industrial, and off-road applications. RoHS compliant units are offered with range of LED colors and feature extended life cycles and sealing to IP67. With self-cleaning contacts, actuation force for momentary action units ranges from 1.5-9 N, with mechanical travel range from 1-2 mm. Model K6 measures 11 x 7.4 x 8.4 mm while K12 key switch measures 12 x 11 x 11 mm.'); document.write('

'); document.write('Allowing manual control of each channel separately via 24 knobs located on front panel, Model 9743 high density, 4-position RJ45 switch system offers Cat 5e RJ45 A/B/C/D switching in only 8.75 in. of panel height. Switch is rated for 10/100/1000Base-T networks, up to Cat5e, and all of its 8 pins are switched.'); document.write('

'); document.write('Available with 28 or 32 W lamp options, Metalux OpticaHP Parabolic Series includes 2 x 4 and 2 x 2 ft luminaires and 2 OpticaHP retrofit kits designed for installation into 2 x 4 or 2 x 2 ft parabolic fixtures that are 2, 3, 4, or 5 in. deep. Luminaire features reflective matte white finish with glare reducing faceted steel cross blades for soft, even light distribution. Energy-saving fluorescent lighting solution suits both new construction and retrofit applications.'); document.write('

'); document.write('Designed for 12 V batteries, 40 A Christie L1240T can recharge ten 4 A batteries in parallel. Unit includes 24-hour timer for safe, extended charging and dual meters that indicate charging voltage and current. Transformer design provides for automatic taper charge reduction as battery group reaches full charge, while automatic current taper ensures low finish charge current.'); document.write('

'); document.write('Intended for smaller embedded device protection of higher current applications, 456 series 40 A NANO²® fuse offers interrupt ratings up to 600 A at 60 Vdc with melting I²t value of 454.51 A² secs. It enables circuit engineers to design-in primary and secondary over-current protection with one 12 X 4.5 X 4.5 mm fuse. Circuit protection device features RoHS-compliant construction free of lead and halogen.'); document.write('

'); document.write('Low pass, C-R-C filters in SP6001 Series feature line capacitance of 24 pF with cut-off frequency of approximately 115 MHz, while SP6002 Series filters have line capacitance of 30 pF with cut-off frequency of about 100 MHz. Each series includes 4- and 6-channel versions that provide attenuation of less than or equal to -30 dB from 800-3,000 MHz. Silicon protection arrays meet IEC61000-4-2 standard and have 6 V reverse standoff voltage with leakage under 1 µA.'); document.write('

'); document.write('Available in current ratings from 125 mA to 20 A, 285 Series is available with gold-plated caps as standard and rhodium-plated caps upon request. Ceramic body of these 5 x 20 mm cartridge fuses lends to breaking capacity of 1,500 A/250 Vac. Used as supplementary protection in appliance or utilization equipment, RoHS-compliant products have max fault current ratings (interrupt ratings) of 1,500 A for 125 mA to 10 A, 500 A for 15 A, and 400 A for 20 A.'); document.write('