document.write('\'Powered'); document.write('
ThomasNet News® - Thermal & Heating Equipment
'); document.write('
ThomasNet News® is a service of ThomasNet.com
'); document.write('
Natural Gas Belt Conveyor Oven reaches temperatures to 350°F.
'); document.write('
'); document.write('Along with 1,650,000 BTU installed in modulating natural gas burner to heat oven chamber, No. 864 features workspace dimensions of 6 ½ x 35 x 1 ½ ft and 24,500 cfm, 20 hp recirculating blower that provides vertical downward airflow to workload. Design includes 5 ft open belt loading zone, 35 ft insulated heat zone, and 1 ft open belt unloading zone. At 6 ft wide, 1 x 1 in. galvanized steel flat wire conveyor belt with ¼ hp motor drive, variable from 5–50 fph, transports workload.'); document.write('
'); document.write('
Dual Tower CPU Cooler provides quiet operation.
'); document.write('
'); document.write('Featuring 150 mm wide fin-stack and widely spaced heatpipes, Model NH-D15 enables uniform heat distribution for optimal efficiency. Recessed lower fins enable NH-D15 to provide 64 mm clearance for tall memory heatsinks in single fan mode. Cooler also features pro-grade SecuFirm2™ multi-socket mounting system and NF-A15 fans that support PWM for automatic speed control through mainboard. Using supplied Low-Noise Adapter, max fan speed can be reduced to 1,200 rpm for quieter operation.'); document.write('
'); document.write('
Continuous Conveyor Oven optimizes curing cycle efficiency.
'); document.write('
'); document.write('Featuring overall dimensions of 14 ft 4 in. x 6 ft 6 in. x 30 ft 4 in. and operation from 200–662°F, Model DTI-390 incorporates conveyor belt that accommodates parts across its entire width, ensuring that each part receives equal amount of airflow. System includes curing chamber, cooling chamber, and 5 individual zones of control, each utilizing its own full modulating natural gas burner, circulation fan, and exhaust fan. At belt speed of 2 ipm, Model DTI-390 cures approximately 3,000 parts/hr.'); document.write('
'); document.write('
Explosion Proof Air Heaters range from 5-30 kW.
'); document.write('
'); document.write('Certified to ATEX and IECEx requirements, AEU1 Series Electric Air Heaters provide primary or supplementary heating for comfort or freeze protection in hazardous locations. Units include ExCaliber™ liquid-to-air heat exchanger cores, which are available in fourteen 400 V, 50 Hz models and fourteen 480 V, 60 Hz models. Housed in 14-gauge steel cabinet with epoxy/polyester powder coating, AEU1 Series incorporates immersion heater, IEC motor, cable glands, and O-rings to minimize moisture ingress.'); document.write('
'); document.write('
Heat Exchangers cool electrical and electronic enclosures.
'); document.write('
'); document.write('Featuring Type 304 stainless steel NEMA 4X construction, HE Series draws heated air from cabinet, thermodynamically cools it, and then returns cooled air to cabinet. Process can cool cabinet interiors to within 5°F above ambient air temperature outside enclosure. Available in wide range of sizes to provide 5.7–83 W/°F of closed-loop heat removal capacity, heat exchangers have epoxy coated aluminum core, 24/48 Vdc and 120/230 Vac power options, and 4 or 10 micron ambient side intake air filter.'); document.write('
'); document.write('
Continuous Conveyor Oven dries lost foam castings.
'); document.write('
'); document.write('With 15-minute drying cycle, Model DTI-223 evaporates 1,121 lb of moisture every hour. System moves products through 3 temperature-controlled zones on polypropylene mesh belt. Each zone, programmable from 180–400°F, utilizes 1 full modulating natural gas burner, 2 circulation fans, and 1 exhaust fan. Providing useable dimensions of 3 ft 2 in. x 98 ft 4 in. x 6 in., oven is controlled by PLC and uses variable frequency drive to adjust speed of conveying system.'); document.write('
'); document.write('
Gas-Fired Walk-in Oven can be used for heat cleaning.
'); document.write('
'); document.write('Featuring 880,000 BTU installed in modulating natural gas burner to heat oven chamber, No. 910 reaches temperatures to 1000°F and offers 60 x 120 x 78 in. workspace. Recirculating blower (rated 12,500 cfm, 10 hp) provides combination airflow to workload, and safety equipment includes 1,500 cfm, 2 hp powered forced exhauster. Along with insulated walls and floor, additional features include inner and outer door gaskets as well as digital programming temperature controller.'); document.write('
'); document.write('
Gas Fired Oven cures pleated filters for aerospace industry.
'); document.write('
'); document.write('Operating at 350°F and capable of reaching 400°F, adjustable line speed conveyor oven features heating chamber with 20 ft long x 5 ft 8 in. wide interior and 7 in. clearance above belt. Overall conveyor length is 29 ft 10 in., with 3 ft end extensions at entrance and exit, and flat wire steel belt is supported by steel slide bed. Manual and adjustable sheets located by oven openings reduce heat loss, while top and bottom ducts accelerate moisture curing on filter material.<br />'); document.write(''); document.write('
'); document.write('
Benchtop Reflow Oven features Android OS and touchscreen UI.
'); document.write('
'); document.write('Simulating environment of inline reflow system, Wi-Fi-enabled MC-301 measures 27 x 19 x 11 in., features multi-zone heating chamber, and can be used for prototyping, manufacturability testing, and short-run batch production. Android control app lets SMT assemblers and product developers meet solder paste manufacturer specifications for preheat, soak, reflow, and cooling phases of recommended profiles. Also, heating/cooling rates in each stage are automatically calculated.<br />'); document.write(''); document.write('
'); document.write('
Advanced Reflow Systems include batch ovens and inline variants.
'); document.write('
'); document.write('Via combination of hot air reflow, nitrogen purge, and heat circulation vacuum, Eightech Vacuum Reflow RNV Series can reduce presence of solder joint voids when soldering larger PCBs and area-array packages. Flux-free soldering, accomplished by utilizing vacuum reflow in combination with hydrogen/formic acid, provides such benefits as no-flux wash process, minimized influences on insulation resistance and ion migration, as well as void-free soldering.'); document.write('
'); document.write('
Continuous Conveyor Oven features multiple zones of control.
'); document.write('
'); document.write('Featuring two electric heaters programmable to operate from 200° and 220°F, DTI-226-100 cures adhesive on drum brake linings used in automotive industry. Dual individual zones let operator fine tune curing process for different products while also conserving energy. Capable of curing 2,011 linings/hr, oven utilizes curing and cooling chamber in-line. Other features include flat wire belt, VFD, vertical top-down air flow, and useable 17 ft 6 in. x 5 ft 6 in. x 1 ft curing chamber dimensions.'); document.write('
'); document.write('
Simulation Software optimizes waste heat recovery cycles.
'); document.write('
'); document.write('While offering calculations for heat balance and thermodynamic simulations, AxCYCLE™ v2.3 also provides fluid library that helps engineers develop models and cycles tailored for waste heat recovery for internal combustion engines. Optimized mapping functionalities and graphics are also featured, along with ability to run multipoint analysis for different operating conditions. Built-in OEM internal combustion engine library and OEM gas turbine library can be customized.'); document.write('
'); document.write('
Adhesive Tank Melters simplify use of reactive PUR adhesives.
'); document.write('
'); document.write('Aiding and enabling polyurethane (PUR) adhesive use in manufacturing and assembly, VersaPUR™ systems have smooth, non-stick release-coated surfaces and tiltable tank. Graphic controls simplify programming and provide visibility of system status. Along with integrated or external inert gas supply, additional features include optional sensor and warning for tank level, various variable-speed gear pump options, and choice of manual or automatic pressure controls.'); document.write('
'); document.write('
Inert Atmosphere Oven operates up to 932°F.
'); document.write('
'); document.write('Providing 54 x 36 x 84 in. workspace dimensions, No. 1033 comes equipped with 60 kW Incoloy-sheathed tubular elements as well as 10,000 cfm, 7½ hp recirculating blower that provides vertical downward airflow to workload. Oven is constructed with 8 in. thick insulated walls, aluminized steel exterior, and Type 304, 2B finish stainless steel interior. It includes gas pressure regulator, flow meter, pressure gauge, internal high-temperature gasket, and air jacket on inner oven for cooling.'); document.write('
'); document.write('
Drying Oven Service targets implantable medical devices.
'); document.write('
'); document.write('Developed in response to medical device manufacturers’ need to dry temperature-sensitive products, Drying Process Development service saves time, trial and error of discovering best process and equipment for application. Once drying process has been developed and proven, Cascade TEK can deliver oven built to execute that process, or perform drying process in A2LA accredited laboratories. Vacuum drying ovens are delivered with controller programmed, pump installed, and with on-site startup.'); document.write('
'); document.write('
Refractory Shapes produce clean, contaminant-free metals.
'); document.write('
'); document.write('Dense, hard, and chemically stable Cerox® fired refractory shapes are resistant to chemical attack from acids, slags, and gases and come in various material compositions. Fired to temperatures that create strong molecular bonds, shapes provide cleaner, contaminant-free metal desired by end-users in aerospace and automotive steel foundries. Variants include Sillimanite Cerox 200 (74% alumina and fired mullite), Cerox 700 (versatile shape capability), and Cerox 720 (for complex shapes).'); document.write('
'); document.write('
Electric Forced-Air Explosion-Proof Heater comes in 35 kW model.
'); document.write('
'); document.write('Featuring 35 kW heater, XEU1 series provides heating for comfort or freeze protection in hazardous location-classified areas. Unit incorporates immersion heater, fan and motor assembly, 14 GA steel cabinet with epoxy/polyester powder-coating, dual safety high limits, vent relief device, control enclosure, and enclosure O-rings. Three cabinet sizes include ExCaliber™ air evacuated liquid-to-air heat-exchanger cores, which come in 29 voltage and heat output combinations.'); document.write('
'); document.write('
Miniature Thermoelectric Modules offer optimal heat dissipation.
'); document.write('
'); document.write('Built using Tlam thermally conductive circuit boards, Tlam OptoTEC® series is designed for applications where temperature stabilization of sensitive optical components is critical. Circuit boards have thin layer of thermally conductive dielectric material between copper foil layer and metal backing plate. Comprising 7 modules, series can create temperature differential (ΔT) of up to 67°C and pump from 1.5–9.0 W of heat at 25°C. At 85°C, series can create ΔT of 77°C and pump 1.6–9.9 W of heat.'); document.write('
'); document.write('
Drum/Tote Oven melts materials chilled by cold weather.
'); document.write('
'); document.write('Sahara Hot Room Model S32 heats and accelerates flow of thick or viscous materials in drums or totes chilled by cold weather. While able to heat 32 drums on pallets or 8 totes with saturated steam up to 200 psig, forklift-portable oven can also use hot oil or hot water as heating medium. Fully insulated unit features steel construction and built-in spill containment. Options include air circulation, exhaust capabilities, and digital temperature control with overtemp protection.'); document.write('
'); document.write('
Blanket Heaters utilize high R-value foam insulation.
'); document.write('
'); document.write('Combining foam insulation with silicone rubber heaters, High-R Value Silicone Foam Blanket Heaters are designed for thermal applications requiring insulation to cut heat loss that sub-optimizes heater performance. Insulation also provides touch-safe protection in work environment. Designed to fit contours of components, molded homogenous assemblies deliver maximum thermal transfer and temperature uniformity. They can include temperature sensors, thermostat, and other components.'); document.write('
');