document.write('\'Powered'); document.write('
ThomasNet News® - Lubricants
'); document.write('
ThomasNet News® is a service of ThomasNet.com
'); document.write('
Dual-Action Penetrant/Lubricant is VOC-compliant in all 50 states.
'); document.write('
'); document.write('Dual-action penetrant and lubricant with PTFE, Zep® 45 DualForce™, penetrates into tight spaces to loosen stuck parts and lubricates to protect surfaces. With <10% VOCs, industrial-grade solution also incorporates rust-prevention technology to promote corrosion resistance. Once applied, product continues to penetrate for 10 min or longer while minimizing wear. Large pad actuator with fan mist spray aids wide area application, while straw enables pinpoint stream accuracy in narrow areas.'); document.write('
'); document.write('
Copper-Filled Grease suits heat transfer applications.
'); document.write('
'); document.write('Consisting of single-part, 100% solids, thermally conductive, silicone grease, Heat-Away™ 640 is used in heat transfer applications from -60 to 550°F. Product is formulated as thick paste that will not flow after application and maintains stable viscosity over entire temperature range. With thermal conductivity of 4.68 W/m-K, grease optimizes thermal transfer between heaters and process vessels and various heat sinks used in heat exchangers in electrical and electronic applications.'); document.write('
'); document.write('
Synthetic Motor Oil protects European vehicles.
'); document.write('
'); document.write('Formulated with low sulfated ash, phosphorus, and sulfur, SynGold™ European Low–SAPS 5W-30 Motor Oil protects high-performance European vehicles requiring low-viscosity formulation while meeting strict European requirements for gasoline and diesel engines. Product minimizes wear and viscosity breakdown while offering optimized fuel economy performance, cleaning strength, and engine protection, even during extended oil change intervals.'); document.write('
'); document.write('
Hydraulic Fluids target environmentally sensitive areas.
'); document.write('
'); document.write('Designed to help prevent contamination and fines in regulated or environmentally sensitive hydraulic applications, Clarion Green Synthetic Fluids are fully synthetic and are available in ISO 22, 32, 46, and 68 viscosity grades, while Clarion Green BIO Fluids are formulated with high oleic natural esters and are available in ISO 32, 46, and 68 viscosity grades. Both anti-wear products are biodegradable, non-toxic in acute aquatic toxicity test, ashless, and zinc-free.'); document.write('
'); document.write('
Seed Lubricant reduces total amount of released dust.
'); document.write('
'); document.write('As lubricant for corn and soybean seeds, Fluency Agent replaces talc and graphite seed lubricants. Product helps reduce amount of total dust released in treated seeds, minimizing potential risk of exposure to honey bees and other pollinators. As application guideline, solution is applied at rate of 1/8 cup per 80,000 kernel seed corn unit or 1/8 cup per 140,000 seed soybean unit, and can be used in all makes and types of planting equipment that recommend use of seed lubricant.'); document.write('
'); document.write('
Synthetic Lubricant Base Stock combines two key technologies.
'); document.write('
'); document.write('Combining composition and properties of synthetic esters and PAOs into single product, Elevance Aria™ WTP 40 provides differentiated performance in broad markets such as engine and gear lubricants, industrial and hydraulic fluids, and greases. Product features high viscosity index of 160 and balanced aniline point of 95, which is an improvement over both Group IV and Group V base stocks.'); document.write('
'); document.write('
General-Purpose Grease withstands severe conditions.
'); document.write('
'); document.write('Combining high-viscosity base fluid, calcium sulfonate complex thickener, and Monolec® wear-reducing additive, Monocal™ GP Grease protects equipment from heat, moisture, and heavy loads. Formula imparts high dropping point, inherent extreme pressure characteristics, mechanical stability, low oil bleed, and water resistance. Calcium sulfonate thickener prevents rust and corrosion, while Monolec protects against metal-to-metal contact, resists oxidation, and helps grease maintain consistency.'); document.write('
'); document.write('
Metalworking Lubricant features vegetable-derived formula.
'); document.write('
'); document.write('Intended for severe hardened steel and stainless steel machining applications, EQO-PURE 452 includes extreme pressure additives to optimize tool life and part quality while eliminating foaming and staining. Vegetable-based, water-soluble micro-emulsion fluid offers bioresistant qualities and provides corrosion control for ferrous metals. Applications include boring, deep-hole drilling, gun drilling, reaming, roll forming, tapping, and threading.'); document.write('
'); document.write('
Synthetic Greases target rolling and plain bearings.
'); document.write('
'); document.write('Based on synthetic hydrocarbon oil and barium complex soap, ISOFLEX TOPAS NB 52 and ISOFLEX TOPAS NB 152 protect against corrosion, oxidation, and aging. ISOFLEX TOPAS NB 52 is suitable for temperatures ranging from -60 to 250°F and short peak temperatures up to 300°F, while ISOFLEX TOPAS NB 152 can be used in wide service temperature range of -40 to 300°F. Some applications include bevel gears, roller coaster wheel bearings, fan bearings, and pump bearings.'); document.write('
'); document.write('
Synthetic Oven Chain Lubricant fights heat and moisture.
'); document.write('
'); document.write('In addition to meeting NSF criteria for incidental food contact, Ovenworx™ H1 Syn Chain Lubricant (4061) is low-staining, odor-neutral, and contains no artificial dyes. Fully synthetic formula features high-viscosity base fluid that penetrates all moving parts of oven chain, enabling them to move freely. Capable of lubricating chains up to 572°F without solid additives, product seals out damaging moisture, preventing corrosion that can lead to premature failure of chain pins and bushings.'); document.write('
'); document.write('
Wire Drawing Surface Treatment has no Borax or Phosphate.
'); document.write('
'); document.write('Supplied in powder form, VICAFIL TS 7112 is diluted in hot water bath and contains mineral salts classified as non-toxic. Mineral salts and organic-polymers of VICAFIL TS 7112 crystallize quickly on wire, creating optimal coverage and greater deposit weight, ensuring adherence and distribution of lubricant during wiredrawing operation. This results in accelerated wiredrawing speeds, minimized die wear, and wire surface quality.'); document.write('
'); document.write('
Forging/Dry Film Lubricant protects die and increases life.
'); document.write('
'); document.write('Effective at temperatures up to 750°F and suitable for cryogenic conditions, McLube MoS2-900 chemically and thermally stable, water-based molybdenum disulfide forging lubricant and bonded dry film lubricant is also suited for use as general-purpose dry lubricant as well as run-in lubricant. Dry lubricant coating, after evaporation of water, exhibits durability, 0.035 coefficient of friction, and 225,000–500,000 psi load carrying capability. Product prevents seizing, galling, and scoring.'); document.write('
'); document.write('
Synthetic Transmission/Hydraulic Oil protect in all temperatures.
'); document.write('
'); document.write('Champion 4000® Ultra Synthetic with DYNAVIS® Technology contains additives and shear stable polymer thickeners that promote efficiency and protection in all temperatures. While minimizing pumping losses and startup wear, low temperature pumpability and high temperature shear stability also ensure maximum film strength and minimum internal leakage at any operating temperature. Fluid meets OEM summer and winter grade specifications as well as pump test requirements.'); document.write('
'); document.write('
Lubricating System uses effective, simplified approach.
'); document.write('
'); document.write('Suited for smaller pressrooms and vanishing oil applications, Spra-Rite Alpha Lubricating System controls lubricant application to stamped and drawn material or tooling process. Turnkey solution includes controller, injector manifolds, 5-gal stainless steel tank, nozzles, and tubing. Process control module offers numeric programming for up to 6 injector valves as well as purge/test feature, and each injector is independently controlled for precise lubricant placement and volume control.'); document.write('
'); document.write('
Boundary Lubricant prevents metal-to-metal contact.
'); document.write('
'); document.write('Suitable for high-end manual chucks or power chucks, HPG500 Lubricant prevents metal-to-metal contact under high load and slow speed conditions. NLDI Grade 2 lubricating grease offers optimized water and moisture resistance, with water washout rating of less than 3%. Formula also provides rust and corrosion resistance, even in presence of synthetic and oil-based coolant environment. Lithium-free, all-purpose industrial lubricant can be used in bearings, bushings, slides, pivots, and tracks.'); document.write('
'); document.write('
Metalworking Fluid maintains environmental health and safety.
'); document.write('
'); document.write('Providing bio-chemical stability and long sump life without use of bactericides, chlorine-free Blasocut® BC935SW offers extended tool life in cast iron, steel, aluminum, and exotic alloys. Product delivers optimized washing action and low misting properties for machine and shop cleanliness. Formulated for use in water with max hardness of 140 ppm, Blasocut® BC935SW provides foam control in moderate to high coolant pressure applications.'); document.write('
'); document.write('
Electric Reciprocating Pumps meet lubrication needs.
'); document.write('
'); document.write('Designed to supply grease to injector-based, series progressive, and dual line metering systems, Dyna-Star HP is capable of 5,000 psi with max output of 18 in.³/min, while Dyna-Star HF is capable of 3,400 psi with max output of 25 in.³/min. HP model features vent and fill path design that converts drum into injector-based system without extra hoses or drilling holes. Both 24 Vdc pumps incorporate Advantage Drive™ sealed gear set with helical hardened steel gears that are lubricated for life.'); document.write('
'); document.write('
Temporary Rubber Assembly Lubricant does not leave residue.
'); document.write('
'); document.write('Solvent-free, water-based, and non-hazardous P-80® RediLube provides temporary lubrication to aid assembly of tight-fitting parts. Offering ample lubrication when wet, this biodegradable and non-toxic solution improves assembly operations by making rubber easier to install, remove, or otherwise manipulate. It does not leave interfering residue; once dry, slipping action goes away. Free of petroleum distillates and silicon, product will not dry, crack, or otherwise harm rubber parts.'); document.write('
'); document.write('
Diesel Motor Oil helps achieve fuel economy goals.
'); document.write('
'); document.write('Formulated with patented friction modifier system, SAE 5W-30 UltraFleet® API-CJ4 Synthetic Heavy Duty Diesel Motor Oil minimizes internal drag, engine wear, and corrosion while maintaining viscometric properties. Oil has 50% faster time to pressurization than traditional SAE 15W-40, leading to accelerated lubrication of critical valve train hardware and emissions system components.'); document.write('
'); document.write('
Nano-Ceramic Grease is available in numerous package sizes.
'); document.write('
'); document.write('DayLube features nanoceramic particles acting as sub-microscopic ball bearings to provide continuous lubrication to steel surfaces. Available in 16 oz tubes, jars, and 1 and 5 gal containers, it is chemically inert, wear-resistant, and maintains viscosity across temperature range of -40°F to +800°F. Nanoceramic particles remain intact to 2,500°F. Product also has high load-bearing properties, low dielectric constant, and resistance to steam, acids, and most chemical products.'); document.write('
');