Electrodes & Rods

Materials & Material Processing, Electronic Components & Devices, Welding Equipment & Supplies

Spatter-Free Electrode welds zinc galvanized, primer coated steel.

February 9, 2015

Available in .035, .045, and 1/16 in. dia, Select 70C-6 ZN consists of carbon steel, composite metal cored electrode that carries E70C-6M-H4 classification per AWS A5.18. Wire provides stable arc with fine spray transfer that produces spatter-free welds at travel speeds to 80 ipm with optimized sidewall fusion. Also, arc stability through both standard CV and pulse parameters enables welding over zinc galvanized and coated carbon steels. Read More

Welding Equipment & Supplies

Composite Metal Cored Electrode welds aluminized material.

January 8, 2015

Intended for welding of ferritic stainless steel, particularly on thin section, aluminized material, Select FP 409Ti comes in .045 in. dia and provides stable spray arc over diverse current/voltage settings with minimal spatter and no burn-through on thin material. Titanium acts as stabilizing agent to provide oxidation and corrosion resistance. Furthermore, resistance to sensitization reduces chances of stress corrosion cracking when welding over lubricants, oils, and other hydrocarbons. Read More

Welding Equipment & Supplies

Metal-Cored Wires maintain strength after stress-relief hold.

October 22, 2014

Hobart® FabCOR® 4130 SR gas-shielded, metal-cored wire and Hobart SubCOR® 4130 SR metal-cored, submerged-arc welding electrode maintain mechanical properties, such as hardness, during extended periods of stress relief. While deposition rates help increase travel speed and productivity, weld deposit strength and chemistry versatility suit joining and repair applications with various materials. Products are intended for use with DCEP polarity and serve single- and multi-pass welding applications. Read More

Welding Equipment & Supplies, Materials & Material Processing

Flux Cored Electrode welds plates with surface contaminants.

October 13, 2014

Available in 3/32 in. dia, Select 70CRP is suited for welding automatic or semi-automatic fillet welds on ship panels, barges, or any structural plate that has been coated with rust-preventive primer or non-coated plate that has rusted. Formulation of this flux cored, carbon steel electrode enables welding on primer and rust with minimal porosity/blowholes. Additionally, wire delivers smooth arc characteristics, minimal spatter, and optimized slag removal. Read More

Welding Equipment & Supplies

Shielded Electrode is suited for low-temperature stress relief.

September 9, 2014

Offered in .045, 052, and 1/16 in. dia, Select 70C-6 SR consists of E70C-6MJ-H4 gas-shielded, metal cored electrode with properties that promote weldability and minimal slag. This results in smooth arc transfer with maximized arc stability. Also, wire exhibits optimized mechanical properties at temperatures down to -60°F in both as-welded and stress relief condition. Suitable welding applications include rootpass welding of process piping, pressure vessel fabrication, and general fabrication. Read More

Welding Equipment & Supplies, Electronic Components & Devices

Stick Electrode resists moisture in humid conditions.

July 22, 2014

Consisting of mild-steel, low-hydrogen stick welding consumable, Millennium Arc™ 7018 is designed for applications in power generation, petrochemical, pressure vessels, and pressure piping. Product has no intentional addition of zinc in its composition, which minimizes zinc in welding fumes. Providing effortless slag removal, electrode delivers flat bead profile and clear weld puddle without slag interference. Read More

Welding Equipment & Supplies, Materials & Material Processing

Welding Electrode exhibits smooth arc transfer.

June 9, 2014

Available in .045, .052, and 1/16 in. diameters, Select 707 E71T-1 Flux Cored Gas-Shielded Electrode provides optimized weldability at low or high current settings while exhibiting arc stability. All-position wire also delivers robust mechanical properties at temperatures as low as -20°F. Applications include general fabrication, structural steel, construction equipment, railcar fabrication, and shipbuilding. Read More

Welding Equipment & Supplies, Electronic Components & Devices

Replacement Electrodes, Holder can be used on multiple torches.

March 20, 2014

Extending electrode life, PT-36®, PT 19XL®, and PT600® replacement Silver-Pro electrodes combine copper body and solid silver insert. This improves conductivity of electricity and efficiently dissipates heat of plasma arc. Electrode holder 0558003924-Ur is compatible with PT-600® and PT-36® systems, while T-11210 electrode holder is compatible with PT-19XL® system. This allows same 450 A oxygen electrode, Silver Pro 0558003914-PrO, to be used with all 3 torches. Read More

Material Handling & Storage, Welding Equipment & Supplies, Machinery & Machining Tools, Electronic Components & Devices

Replacement Electrodes feature silver insert.

February 28, 2014

Combining copper electrode body and solid silver insert, PT-36® Replacement Silver-Pro Electrodes deliver powerful plasma arc while minimizing downtime. Silver insert optimizes conductivity of electricity and dissipates heat of plasma arc more efficiently than standard copper electrodes, extending electrode life. With replacement electrode holder for PT-36® torch, replacement electrodes and OEM’s original electrodes can both be used. Read More

Material Handling & Storage, Paints & Coatings, Welding Equipment & Supplies

Stick Electrode optimizes operator control and weld quality.

January 23, 2014

Available in 1/8 or 5/32 in. diameters, Hobart 610 features concentric design, ensuring even coating along entire length and consistent arc performance. Stick electrode exceeds AWS minimum specifications by offering tensile strength of 78,000 psi and yield strength of approximately 65,000 psi. To minimize cracking in low temperatures, product offers Charpy V-Notch impact values of 45 lb-ft at temperatures of -20°F. It also provides easy weld lay-in and smooth bead appearance. Read More

Welding Equipment & Supplies

Flux Cored Electrode suits stress-relieved applications.

September 10, 2013

Delivering smooth, stable arc, Select 7000-SR is designed for welding carbon and certain low alloy steels where optimal mechanical properties are required in both as-welded and stress-relieved conditions. Gas-shielded, flux cored, all-position electrode has low spatter emission and fast freezing slag. Available in .045, .052, and 1/16 in. diameters, Select 7000-SR is suitable for welding vessels, piping, and other applications demanding low temperature toughness before and after stress relieving. Read More

Welding Equipment & Supplies

Low-Alloy Cellulosic Electrode suits root pass welding.

August 26, 2013

Available in 4.0 mm, 3/16 in., and 5.0 mm dia, Pipeliner® Arc 80 is designed for root pass welding up to X80-grade pipe as well as fill and cap pass welding for X70-grade pipe. Low-alloy stick electrode, classified as E8010-G and E8010-P1 per AWS, fosters productivity in vertical down as well as out-of-position pipe welding and offers deep penetration. Q2 Lot® control shows actual deposited chemistry, and electrode offers clean, visible weld puddle.
Read More

Welding Equipment & Supplies, Materials & Material Processing

Nickel Alloy Electrode withstands rigorous environments.

July 10, 2013

Designed to tackle critical welding applications in demanding environments, SelectAlloy 182-AP produces uniform, well washed beads with minimal weaving, low spatter, and optimized slag peeling. Gas-shielded, flux cored, all position wire offers resistance to hot cracking, corrosion, and oxidation. Available in .045 and 1/16 in. diameters, ENiCrFe-3 class electrode is suitable for welding in desalination plants, petrochemical facilities, power generation plants, and furnace equipment. Read More

Welding Equipment & Supplies, Electronic Components & Devices

Metal Cored Electrode targets oil field applications.

April 8, 2013

Available in .045 a 1/16 in. diameters, Select 4130C is manufactured to match properties of certain quench and tempered steels following post-weld heat treatment. Nickel–chromium–molybdenum bearing wire contains less than 1% nickel in weld deposit and delivers smooth arc transfer with minimal splatter. Select 4130C is suitable for welding 4130, 4140, 8630, and similar alloy steels. Read More

Welding Equipment & Supplies

Replacement Electrodes feature silver insert.

February 27, 2013

Combining copper electrode body with solid silver insert, Silver-Pro Electrodes are available for Hypertherm® HPR 130®/260® systems, ESAB® PT-600® system, and Kjellberg® PERCUT 160®/170®/370.1® systems. Silver insert optimizes conductivity of electricity and dissipates heat of plasma arc more efficiently than standard copper electrodes, resulting in extended electrode life. Read More

Welding Equipment & Supplies

Plasma Cutting Electrode delivers extended consumable life.

July 31, 2012

Manufactured for Duramax(TM) torches, CopperPlus(TM) electrode delivers optimized consumable life when cutting metal up to ½ in. thickness using plasma cutting systems. Drop-in replacement/integration does not require any changes to other consumable parts or system settings. Specific Duramax torches with which this electrode is compatible include Powermax65/Powermax85, Powermax1000/1250/1650/600/800/900, and MAX42/43. Read More

Welding Equipment & Supplies, Electronic Components & Devices

Tungsten Electrodes offer optimized arc starts and stability.

February 13, 2012

Available in 7 in. lengths and 5 diameters of 0.040, 1/16, 3/32, 1/8, and 5/32 in., Tungsten Electrodes come in 2% lanthanated and zirconiated versions. Two percent lanthanated electrodes, providing substitute for 2% thoriated tungsten electrodes, offer minimized tip erosion. Zirconiated tungsten electrodes resist spitting in high current applications, minimizing opportunity for contamination. Units also ball up in AC applications, ensuring smooth arc. Read More

Welding Equipment & Supplies, Materials & Material Processing

Self-Shielded, Flux-Cored Wire suits offshore welding.

December 2, 2011

Designed for welding in narrow TKY joints and poor fit-up conditions, Innershield® NR-440Ni2 features optimal toe wash-in and is capable of delivering flat bead face when used in vertical-up or vertical-down welding applications. Wire meets H8 diffusible hydrogen requirements over range of humidity levels. Available in 5/64 in. diameter on 14 lb coils, product is hermetically sealed in ProTech® packaging for moisture resistance. Read More

Welding Equipment & Supplies, Electronic Components & Devices, Materials & Material Processing

Martensitic Electrodes weld 410 stainless steel.

November 11, 2011

Delivering flat, well washed beads with minimal weaving, Select 410-AP all position wire welds straight 410 SS while providing corrosion and oxidation resistance up to 1,200°F. Select 410NiMo, featuring nominal weld metal composition of 12% chromium, 4.5% nickel, 0.6% molybdenum, and max carbon content of 0.06%, delivers smooth stable arc with low spatter residue and well washed beads. Both gas-shielded, flux cored electrodes are available in .045 in. and 1/16 in. diameters. Read More

Welding Equipment & Supplies, Electronic Components & Devices, Materials & Material Processing

Stainless Steel Electrodes produce little or no spatter.

October 10, 2011

Available in .045 and 1/16 in. diameters, SelectAlloy 16-8-2 Electrodes are composed of 15.5% chromium, 8.5% nickel, and 1.5% molybdenum. Flux cored SelectAlloy 16-8-2-AP, designed to weld in all positions, delivers flat, well washed beads, while metal cored SelectAlloy 16-8-2-C wire provides smooth, spray arc transfer and produces little or no slag. Both gas-shielded electrodes are suitable for welding 16-8-2, 316, and 347 grades of stainless steel in high-temperature piping systems. Read More