Time Mark Corp.
Tulsa, OK 74116 2019
Jun 07, 2002 Model 301 digital timer can be set for 1 of 5 functions that can cover 4 timing ranges. DPDT electro-mechanical output relay prevents unit from being affected by potential power loss or fault conditions. Timer has universal power supply for wide variety of AC and DC voltage ranges.

Selco Products Co.
Orange, CA 92868 1013
Apr 10, 2002 Super Teachme Model 2831 electronic timer has 2 programmable timing ranges with span of 0.05 sec to 54 min, timing resolution of 0.05 sec, and repeatability of 0.10 sec. Operation requires selecting desired timer range using SPST switch and pressing start button. Start button can be connected to AC power line for 110/220V activation or directly to board for low-voltage. Timer measures 3.6 x 2.35 x 1.5 in.

Automatic Timing & Controls
Lancaster, PA 17605
Apr 08, 2002 Model 385 Controller incorporates 3 easily set preset times or counts with built in totalizer that accumulates number of completed cycles. It has dual DPDT relays and EEPROM memory for applications where value must be retained during power failures or outages. Timing or counting display modes are selectable for time/count up or down from setpoint. Range is 0.01 sec to 999 hr. As counter, it works 1 to 9999 or 99990. Setup is done with 16 DIP switches.

Tork
Mount Vernon, NY 10550 2401
Apr 03, 2002 Model 5737TM fits turn-lock photo-control socket. It turns outdoor lighting ON at dusk and OFF at midnight. OFF time can be adjusted for up to 2 hr before or after midnight and is used for extra energy savings or to customize for various longitudes. Smart photo-timer automatically tracks dusk and dawn times as they vary with seasons to determine midnight each day, automatically corrects for daylight savings time, and automatically resets timer after power outages.

TURCK, Inc.
Plymouth, MN 55441
Feb 20, 2002 SmartPlug adds control functions such as timing, counting, inverting and speed monitoring to sensors. Approximately 2 in. long, it connects between cable and sensor. Programming is done via teach input device available separately. Inverter version converts PNP input signal to NPN or vice versa, or NO to NC. Timer is programmable from 1 ms to 65 sec. Counter is programmable to count pulses or intervals. Speed Monitor checks for over or underspeed.

Automatic Timing & Controls
Lancaster, PA 17605
Jan 17, 2002 TSU Universal Binary Switch Timer provides selectable multi-mode operation; single and repeat, delay-on-operate and interval-on-operate with solid-state 1 A output. Timing range of 0.1 seconds to 127 hours is DIP-switch selectable for seconds, minutes, and hours, and is crystal controlled for accuracy. Timer has universal power range of 108 to 264 Vac at 50/60 Hz.

Tyco Electronics Corp.
Harrisburg, PA 17105-3608
Jan 02, 2002 AGASTAT 48K series has 8 timing modes including on delay, off delay, interval, one shot, repeat, cycle on/off delay, on/interval and accumulating on. It can time periods from 0.1 sec up to 10 hr. Rotary selector switch sets timing range, while adjustment knob provides fine-tuning. Repeat accuracy is 0.5% or ± 20 msec. Unit operates on 24-240 Vac, 50/60 Hz, or 24-125 Vdc. Relay contacts are rated up to 10 A resistive at 30 Vdc or 120/240 Vac.

Entrelec Inc./ABB
Irving, TX 75038 4312
Dec 11, 2001 ProgramaCube NHPU Series high power solid state timer/counter module has switch adjustable time delays of 0.1 sec to 1,023 hr in six ranges. Switch adjustment allows accurate selection of time delay or number of counts. Microcontroller timing circuit provides repeat accuracy of 0.1%. Module is available with 6, 10, or 20A high current solid state output. It can switch motors, lamps and heaters directly without addition of contactor.