Process Heaters

HVAC, Thermal & Heating Equipment

Explosion Proof Air Heaters range from 5-30 kW.

March 28, 2014

Certified to ATEX and IECEx requirements, AEU1 Series Electric Air Heaters provide primary or supplementary heating for comfort or freeze protection in hazardous locations. Units include ExCaliber™ liquid-to-air heat exchanger cores, which are available in fourteen 400 V, 50 Hz models and fourteen 480 V, 60 Hz models. Housed in 14-gauge steel cabinet with epoxy/polyester powder coating, AEU1 Series incorporates immersion heater, IEC motor, cable glands, and O-rings to minimize moisture ingress. Read More

HVAC, Thermal & Heating Equipment

Electric Forced-Air Explosion-Proof Heater comes in 35 kW model.

February 10, 2014

Featuring 35 kW heater, XEU1 series provides heating for comfort or freeze protection in hazardous location-classified areas. Unit incorporates immersion heater, fan and motor assembly, 14 GA steel cabinet with epoxy/polyester powder-coating, dual safety high limits, vent relief device, control enclosure, and enclosure O-rings. Three cabinet sizes include ExCaliber™ air evacuated liquid-to-air heat-exchanger cores, which come in 29 voltage and heat output combinations. Read More

Agricultural and Farming Products, Thermal & Heating Equipment

Gas-Fired Hydronic Heating System helps gardens thrive.

January 28, 2014

AquaHeat Gas-Fired Hydronic Heating System is suited for gardeners looking to enhance existing system and help fish and plants thrive. In addition to keeping fish warm to help them thrive, system creates positive impact on vegetables and plants. Fully-assembled solution features off-grid capabilities; heating system runs on propane or natural gas and comes with efficient (10 W/hr) heater that can be run off household electricity, battery, or solar panel. Read More

Thermal & Heating Equipment

Inline Heater suits high-purity solvent heating applications.

November 27, 2013

Constructed of electropolished 316L stainless steel with PFA and PTFE wetted surfaces, Frontier™ Series can be used in single pass or recirculating applications for safely heating chemistries such as EKC265, EKC8730, ST28, ST26, ACT690C, and IPA. Unit includes ½, ¾, and 1 in. tube stub fluid connections and accommodates flow rates up to 75 lpm at pressure drop less than 5 psi. Operating from 120–600 V with 3, 6, 9, 12, 18, 24, or 36 kW power, heater features max temperature of 356°F. Read More

HVAC, Controls & Controllers, Thermal & Heating Equipment

Electric Process Heaters feature 4 kV rating.

November 18, 2013

Available in capacities from 6–100 MMBtu/hr, Electric Heaters and Thyristor Control Panels enable large scale applications that have been previously heated inefficiently by gas, oil, or other methods. These installations can now benefit from near 100% efficiency, zero on-site emissions, and precise temperature control. Read More

HVAC, Thermal & Heating Equipment

Chiller/Heater uses multilayer monolithic ceramic technology.

October 2, 2013

Featuring embedded Tungsten RTD sensor, Extreme Aluminum Nitride Ceramic Chiller/Heater is capable of heating from 100–450°C at 200°C per second and cooling from 450–100°C at 100°C per second. High thermal conductivity and low temperature expansion properties of AIN enable fast temperature response. Applications include semiconductor equipment and analytical instrumentation. Read More

Thermal & Heating Equipment

Screw Plug Immersion Heaters feature NPT fittings.

November 6, 2012

Standard Screw Plug Immersion Heaters are designed at 60 W/in.², 500 W to 18 kW, and 120 V/1 phase to 480 V/3 phase. Threaded fittings ease tank insertion and removal, while tubular heater elements are brazed or welded to NPT fittings for optimal mounting. Offered in 1, 2, and 2½ in. NPT versions, heaters are also available with sheath materials including steel, copper, and Incoloy® 840. They are suited for liquid heating and process temperature control applications. Read More

Thermal & Heating Equipment

Flange Immersion Heaters help control process temperatures.

November 6, 2012

Available with 3–14 in. flanges, Standard Flange Immersion Heaters come in various sheath materials, including 316 passivated SS, steel, copper, and Incoloy® 840. Voltages and wattages range from 60 W/in.², 6 kW, 240 V/1 Phase to 16 W/in.², 167 kW, 480 V/3 Phase. With tubular heater elements brazed or welded to flanges for mounting, heaters are suited for temperature control applications ranging from car washing to heavy industrial applications in chemical, petroleum, water, and metal industries. Read More

HVAC, Thermal & Heating Equipment

Severe-Duty Electric Air Heater has explosion-proof design.

August 20, 2012

Ruffneck(TM) FX5-SD suits severe-duty applications that can lead to accelerated wear of electrical components and damage to heater core, including locations with fluctuating power quality, temporary power generation, vibration, or extended maintenance intervals. Enabling primary interruption of line power to safely protect heater core, integrated dedicated shunt trip circuit breaker operates independent of control circuit and is triggered by redundant heater core high temperature limit. Read More

Thermal & Heating Equipment

Infrared Radiant Tube Heaters offer 99+% efficient reflectors.

August 7, 2012

Available in radiant emitter tube lengths from 10-70 ft with ratings from 40,000-220,000 Btu/hr, ITH Series is used to heat entire buildings or as source of focused spot heating in small occupied areas. Gas-fired units feature optimized burners with self-diagnostic ignition and integral post purge feature. Typical applications include manufacturing and assembly areas, small warehouses and loading docks, vehicle repair shops, aircraft hangars, retail stores, and parking garages. Read More

HVAC, Thermal & Heating Equipment

Make-Up Air Heaters utilize proprietary, efficient burner.

April 13, 2012

For reliability and energy conservation, Cambridge M-Series features 100% direct-gas fired combustion efficiency and includes Low-Fire Start Technology as well as stainless steel burners. Products provide year round ventilation and tempered make-up air for commercial and industrial applications. Available with Variable Frequency Drive (VFD) control to respond to varying air needs, indoor and outdoor mounted units offer ratings up to 75,000 cfm and 8,000 MBtuh. Read More

HVAC, Thermal & Heating Equipment

Heating and Cooling Systems offer 50-600°F temperature range.

December 9, 2011

Heat transfer fluid-based Full Range systems, combined with chiller, deliver respective heating and pumping capacities to 48 kW and 30 gpm. Capable of heating from 50 to 600°F, self-supporting unit incorporates microprocessor-based controller with LCD readout, green-friendly refrigerant, and continuous flow cool oil reservoir. System provides heating and cooling in one package, meets NFPA 79 electrical safety standards, and features insulated nonferrous components on chiller side. Read More

HVAC, Thermal & Heating Equipment

Blower Heaters come in 20 and 50 kW options.

September 26, 2011

Through versatile mounting configurations in wall or ceiling, HVH Series provides vertical or horizontal airflow. Heaters feature epoxy-sealed elements to minimize false trips on ground-fault equipment. Pilot light indicates normal operation of heater, while outlet screen prevents objects from coming in contact with fan. To facilitate service, heaters provide access to internal components through large door at bottom and removable case front. Read More

HVAC, Thermal & Heating Equipment, Green & Clean

Solar Air Heater provides 80.7% peak solar efficiency.

May 2, 2011

Featuring wall-mounted design that simulates glass-like facade, Lubi(TM) produces max output of 254 BTU/h/ft² and temperature increases of up 81°F above ambient outdoor temperatures, making it suitable for pre-heating outdoor air and supplemental heating of facilities. Each 3 x 1 ft polycarbonate panel has 906 perforations, which are dimpled and contoured to prevent rainwater infiltration. Ability to draw air through perforations makes Lubi insensitive to wind speeds of 7 mph or less. Read More

HVAC, Thermal & Heating Equipment

Explosion-Proof Electric Air Heater is CE-marked, ATEX-approved.

March 23, 2011

Equipped with limit controls and heavy-duty core, Ruffneck(TM) FE2 is designed for rugged, industrial applications in harsh environments. Standard features include fan only switch, built-in thermostat, pilot light for HEAT ON indication, and built-in disconnect switch. Available in models that range from 2.5-23.1 kW and 220-440 V, heater also incorporates VacuCore® liquid-to-air heat exchanger and features junction box sized to facilitate installation. Read More

HVAC, Controls & Controllers, Thermal & Heating Equipment, Green & Clean

Solar Air Heater optimizes efficiency via true match airflow.

February 11, 2011

Item No. SAC120CFM, Solar Air Heater Fan with Controller, is factory set to end-user's specification. Using thermistor to constantly monitor inside panel temperature, controller ensures critical airflow matching for optimal efficiency. Solar air heater programmable circuit design enables preset temperature settings, which enable fan to ramp up/down depending on inside panel temperature. Read More

Thermal & Heating Equipment

Polyimide Flexible Heaters aid semiconductor wafer processing.

August 12, 2010

Polyimide heaters, suited for semiconductor wafer processing applications, may be custom-designed to meet unique power supply requirements. Heaters can be made to meet exact application requirements through precise temperature distribution. Capabilities include surface mount component integration, thermal subassemblies, and fine etch trace of 0.01 in. as well as surface flatness of 15 µm. Polyimide heater operates up to 250°C and watt densities to 40 W/in.² (typ). Read More

HVAC, Thermal & Heating Equipment, Green & Clean

Heaters offer split zoning capabilities.

October 27, 2009

Available in indoor and outdoor versions, STAR LINEUP P-Series A30/A36 models feature H2i® hyper-heating capabilities that provide heating down to -13°F. Units also offer moisture removal and optimized HSPF. Ducted PEAD-A indoor model features adjustable return from rear to bottom, quiet operation as low as 30 dB(A), multiple fan speeds, and built-in drain pump. Read More

Material Handling & Storage, Chemical Processing & Waste Management, Thermal & Heating Equipment, Cleaning Products & Equipment

Drying Systems are intended for solar cell metallization.

July 16, 2009

Along with belt speeds to 6 m/min and max throughput of up to 5,700 wph, RDS 2100 and RDS 3000 offer process and thermal control features that enable PV manufacturers to promote efficiency and yield. Drying process combines either 5 or 7 IR zones and one central convection zone, delivering temperature profiling adjustable for precision and flexibility. Horizontal throughput systems ensure safe transport through oven via mesh belt or pin chain for up to 3 lanes. Read More

Thermal & Heating Equipment

Line Heating System features modular design.

August 6, 2008

Offering precisely controlled heat distribution, RELIALINE(TM) 170 is automatically self-regulating for temperature uniformity. System fits outer diameter of standard tubing, creating close contact with maximum surface coverage. Internal rails are spring loaded to allow for click-on fit and maximum contact force for optimal thermal transfer. Incorporating double pane design that uses air as insulator, insulation system ensures outside surface temperatures are safe-to-touch. Read More