Ground Heaters

Test & Measuring Instruments, Thermal & Heating Equipment, Optics & Photonics

In-Situ Electron Microscopy Tools foster real-time observation.

November 19, 2015

NanoEx™ holders enable materials scientists and engineers to observe, in real-time, changes at micro, nano, and atomic scale in morphology and dynamic properties of materials under mechanical, electrical, and thermal stimuli as well as environmental conditions mimicking actual use cases. Specific products include NanoEx i/v heating solution, which uses MEMS-based nanoheaters; NanoEx 3D Indenter; and NanoEx 3D STM/EP electric nanoprobing solution. All work with FEI TEM platforms. Read More

Thermal & Heating Equipment

Heat Exchanger Unit Heaters serve rig-based steam applications.

October 19, 2015

Steam Rig Heater (SRH2) series serve steam applications on drilling rigs where boiler failure or system neglect can lead to freeze-up conditions. During accidental freeze-up, SafeDeform™ core headers accommodate ice expansion. Products accept operating steam pressures up to 150 psig in single-pass configurations and meet ASME requirements with National CRN to conform to Safety Codes Act. Also available, 36 in. fan size model integrates speed reducer. Read More

Optics & Photonics, Thermal & Heating Equipment

Edge Heating System optimizes TEM performance.

August 3, 2015

Combining Aduro semiconductor-based thermal sample supports with redesigned TEM holder, Aduro with Edge technology optimizes thermal accuracy and uniformity for in situ heating experiments while minimizing thermal drift. Edge technology maximizes performance of Transmission Electron Microscope by allowing scientists to visualize materials at nano and atomic scale while at accurate and uniform temperatures. It provides 99.5% temperature uniformity of imaging area with 95% thermal accuracy. Read More

Thermal & Heating Equipment

Molded Foam Silicone Rubber Heater aids semiconductor production.

July 1, 2015

Promoting thermal efficiency and higher process temperatures in semiconductor equipment applications, SENTINEL® Molded Foam Silicone Rubber Heaters are available in standard IDs of 1.0, 1.5, 2.0, 4.0, and 6.0 in. in straight sections, elbows, tees, reducers, and flanges. Products can also be designed to dimensions of valves, regulators, and other gas delivery and pump line components. Structured silicone rubber heater and extruded silicone insulation technology are also available. Read More

Thermal & Heating Equipment

Mica Foil Heaters provide uniform heat with fast response.

May 29, 2015

Suitable for applications up to 1,112°F, Mica Foil High Temperature Heater technology utilizes distributed wattage etch foil heater element bonded between high-temperature mica sheath material. Heaters must be clamped and can be designed with custom shapes that match working surface of application. Technology is suited for foodservice equipment, material bonding, and laminating applications where temperature profile and thermal response are critical to manufacturing process. Read More

Thermal & Heating Equipment

HPLC Column Heater controls temperature to 90.0°C.

May 1, 2015

With temperature range of room temperature to 90.0°C, readable and settable to 0.1°C, EchoTherm™ Model CO20 holds columns up to 30 cm long x ¼ or 3/8 in. dia in mounting clips with room for guard columns and fittings. Larger diameter columns may be used by removing column clips. PID temperature control software regulates temperatures to ±0.1°C, and temperature accuracy and stability are ±0.1°C. Other features include temperature stability Indicator lamp, injection counter, and 30-day timer. Read More

Thermal & Heating Equipment

Trench Heaters are designed for space-limited residences.

November 25, 2014

Providing efficient and safe operation, trench hydronic heating solutions are suited for use in areas where wall space is limited as well as areas with floor-to-ceiling glasses or extensive glazing. Design facilitates installation and maintenance and can be customized regarding such options as colors, finishes, and materials. Supplied with heavy-duty floor grills, these trench heating solutions meet requirements of those living in compact apartments.

Read More

Thermal & Heating Equipment

Heating System withstands continuous flexing.

September 5, 2014

Typically manufactured using multi-stranded, insulated corrosion-resistant wire, UltraFlex Heater can be designed in wide range of shapes and sizes. Unit has maximum operating temperature of 302°F and is available in sizes up to 28 x 44 in. with 15 W/in.² maximum watt density. Applicable to multiple flexing applications, UltraFlex can be molded to best fit final product as well as laminated or layered to customer's specifications. Read More

Thermal & Heating Equipment

Silicone Rubber-Based Heater has wrap-around design.

November 15, 2013

Elastic Wrap Heater serves applications that require heating for freeze protection or to prevent condensation. Based on silicone rubber heater technology, lengths of heater are coiled, and cord's elasticity facilitates wrapping around pipes, tubes, and fittings. Molded end protector snaps around pipe to provide structural support for lead wires. Available in 120 and 240 Vac variants, heaters come in widths up to 1.0 in. and straight lengths up to 125 in. Read More

Thermal & Heating Equipment

Compact HPLC Column Heater has room temperature to 90°C range.

July 24, 2013

Along with PID temperature control software that regulates temperatures to ±0.1°C, EchoTherm™ Model CO20 has temperature range that can be read and set to 0.1°C. Temperature accuracy and stability are ±0.1°C; stable temperature indicator lamp on front panel that lights when target temperature is stable to within ±0.2°C. Heater holds columns up to 30 cm long by ¼ or 3/8 in. dia in mounting clips provided with room for guard columns and fittings. Larger diameter columns can be accommodated. Read More

HVAC, Thermal & Heating Equipment

DIY Plug-In Seat Heater safely enhances operator comfort.

January 17, 2012

Promoting driver comfort in cold climates and even providing therapeutic assistance for back muscle pain, Do-it-yourself (DIY) plug-in seat heater can be installed in less than 5 min and regulates heat to 110°F. U.S.-manufactured, Class 6, 7, 8 truck seating accessory comes ready-to-use. After installation, heater plugs into truck's 12 V accessory/cigarette outlet. Read More

Thermal & Heating Equipment, Electrical Equipment & Systems

Medium Wavelength Infrared Lamps are suitable for thin films and plastics.

August 31, 2011

Complimentary to various substrates, Fast Response Medium Wavelength Lamps (FRMW) are engineered to optimize radiation of energy within medium wavelength range. Medium wave IR energy output by these heaters is absorbed by water, inks, paints, and plastics. Supplied in lengths up to 52 in., IR lamps are capable of color temperature of 2100°F and peak wavelength of 2.0 microns. This frequency can be generated with up to 100 W per linear inch. Read More

Thermal & Heating Equipment

Foam Silicone Rubber Heaters conform to gas delivery/pump lines.

August 18, 2011

Used in PECVD, LPCVD, plasma etch, and other vacuum applications, Molded Foam Silicone Rubber Heaters help reduce sublimation of ammonium chloride, nitrides, and other potential hazardous materials by heating forelines, vacuum lines, and vacuum pumps. Silicone molded foam and formed heater construction is clean room compatible. Product is formed or molded to dimensions of stainless steel components, eliminating cold spots where chance of condensation or sublimation increases. Read More

HVAC, Thermal & Heating Equipment, Green & Clean

Heaters offer split zoning capabilities.

October 27, 2009

Available in indoor and outdoor versions, STAR LINEUP P-Series A30/A36 models feature H2i® hyper-heating capabilities that provide heating down to -13°F. Units also offer moisture removal and optimized HSPF. Ducted PEAD-A indoor model features adjustable return from rear to bottom, quiet operation as low as 30 dB(A), multiple fan speeds, and built-in drain pump. Read More

Thermal & Heating Equipment

Heaters promote temperature uniformity in PV equipment.

August 19, 2008

Interference Fit Construction Heaters address photovoltaic (PV) cell substrate applications requiring large heated surfaces. Insertion of tubular style heater into undersized mill groove pattern offers repeatable thermal performance and promotes reliability of entire heated plate by eliminating potential hot or cold spots. Single sheets or array of small heaters can be produced to achieve dimensions larger than 47.24 x 55.11 in. with process heater temperatures greater than 1,022°F. Read More

HVAC, Thermal & Heating Equipment

Chilling/Heating Dry Baths feature 5-program memory.

August 16, 2007

Peltier-driven and fully programmable, EchoTherm(TM) IC35 Series stores 5 programs in memory - with 10 steps per program - for instant recall and use. Each program can be made to repeat automatically from 1-99 times. Heavy-duty dry bath models IC35 (-10 to +100°C) and IC35XT (-20 to +100°C) can freeze, chill, or heat samples in variety of sample blocks that hold 0.5-50 ml centrifuge tubes, test tubes, vials, assay plates, and round-bottom flasks. Each measures measure 8.5 x 10 x 4 in. Read More

Thermal & Heating Equipment, Laboratory and Research Supplies & Equipment

Heaters handle various sample types in aluminum blocks.

June 5, 2007

Available in analog or digital versions, Dry Block Heaters can accommodate 1, 2, 3, 4, or 6 modular blocks. Digital version features microprocessor controls for temperature uniformity, timer with audible alarm, and heats from ambient to 120°C. With 2 temperature adjustment knobs, analog unit heats from ambient to 150°C. Heaters are suited for educational, bio-pharma, food and beverage, industrial, environmental, research, and clinical markets. Read More

Material Handling & Storage, Thermal & Heating Equipment

Syringe Heater ensures consistent material viscosity.

July 29, 2005

Intended for programmable temperature control and preheating of dispense materials, DL Syringe Heater is available in 10 and 30 cc sizes, and operates at 24 V up to 65 W. Unit is precision engineered from aluminum to conduct heat directly to syringe, while non-conductive mounting prevents transfer of heat to valve or motor. When combined with DL HY-FLO(TM) Valve, Syringe Heater provides complete solution for large-volume liquid dispensing applications. Read More

Thermal & Heating Equipment

Insertion Heaters are split along length of cartridge sheath.

June 24, 2002

Model SST has single split sheath, with 2 sections that expand outward. QST, or Quad model has additional sections that expand outward in 4 directions. Both have single-circuit design, provide sheath temperatures up to 1400°F, and watt densities up to 100 W/sq in. Heaters have Incoloy® sheath and ceramic bushing under potting cap providing isolation of connector. SST ranges from 3/8 to 3/4 in dia, while QST ranges from 1/2 to 3/4 in. dia. Read More

Thermal & Heating Equipment

Zone Heater provides uniform platen temperature.

April 17, 2002

Maxi-Zone High Temperature Insertion Heater heats large platens for hot metal presses requiring continuous sheath temperatures to 2000 deg F. It provides 2 or 3 independently-controlled temperature zones along heater sheath, for better control over hot metal forming processes. Heater is available in lengths from 8 to 172 in., and diameters from 0.685 to 0.935 in., for nominal platen passages from 9/16 to 1 1/4 in. dia. Read More