Flow Meters

Sensors, Monitors & Transducers, Test & Measuring Instruments

Magnetic Flowmeter suits utility water applications.

August 13, 2015

Offering intuitive solution for utility, water, and wastewater measurement, Rosemount® 8750W features welded coil housing for protection against moisture ingress, dual compartment transmitter housing to keep electronics fully isolated from moisture, and replaceable terminal block which enables repair in field without replacing entire meter. System also provides intelligent diagnostics, including SMART Meter Verification, grounding and wiring fault detection, and electrode coating detection. Read More

HVAC, Sensors, Monitors & Transducers, Test & Measuring Instruments

Bi-Directional Flow Sensor suits medical applications.

July 17, 2015

Utilizing MEMS thermal accelerometer platform, Model MFC2030 is suited for analytical instruments, anesthesia, and other medical flow devices as well as process control and natural gas measurement. Suspended-bridge microstructure, coupled with advanced CMOS circuitry and 16-bit on-chip A/D, provides wide flow dynamic range. Highly configurable, Model MFC2030 offers multiple mounting options including manifold mount, BSP and NPT fittings. Read More

Test & Measuring Instruments

Magnetic Flowmeter combines reliability, intelligent diagnostics.

July 17, 2015

Rosemount® 8700M offers Modbus output and access to diagnostics, including SMART™ Meter Verification and electrode coating detection, that provide users with data about flowmeter, installation, and process. Suited for remote locations where power is limited, flowmeter provides scalable power supply options. All diagnostic information is readily available in any environment via through-the-glass local operator interface, and terminal compartments facilitate installation and field wiring. Read More

Sensors, Monitors & Transducers, Test & Measuring Instruments

Thermal Mass Flow Meter suits gas monitoring applications.

June 29, 2015

Suitable for applications monitoring natural gas, air, and digester gas, Model FT1 utilizes DDC-Sensor™ consisting of direct digitally controlled sensor technology for calculating accurate gas correlations. Correlation algorithms allow meter to be calibrated on single gas in factory while providing user ability to select other gases in Gas-SelectX™ gas menu. With Zero CAL-CHECK™ feature, users can confirm that meter is functioning properly and accurately with push of button. Read More

Sensors, Monitors & Transducers, Test & Measuring Instruments

Thermal Mass Flowmeters support in-field gas recalibration.

June 17, 2015

Enabling users to retain accuracy without returning thermal mass flowmeter to factory for gas recalibration, QuadraTherm 640i/780i with qMix™ gas mixing software let users create custom gases or gas mixtures to compensate for gas compositional changes in field. Operators can, via included software package, also create and upload unlimited gas mixtures onto meter, save custom gas mixtures onto personal My Gases Database for later use, and download accurate gases from qTherm Gas Database. Read More

Material Handling & Storage, Test & Measuring Instruments

Metering Skids are light hydrocarbon custody transfer certified.

May 27, 2015

Respectively featuring 3, 4, and 6 in. lines for 3,300, 5,500, and 13,670 lb/min max loading rates, Models LMS080 (truck loading), LMS100 (railcar loading), and LMS150 (ship loading) come completely assembled for horizontal or vertical installation. Standard components include Promass Coriolis mass flow meter, batch controller, grounding system, temperature sensor, digital start-stop valve, Y-strainer, isolation valves, frame, piping, Ex d junction box, and other associated components. Read More

Electrical Equipment & Systems, Optics & Photonics, Test & Measuring Instruments

Totalizing Transmitter enables remote turbine meter monitoring.

April 27, 2015

Intended for installation on new or existing turbine meters or pulse devices, Rosemount® 705 wirelessly provides average flow rate and totalization in operator-configurable k-factor. Unit also delivers predictive diagnostics data to indicate instrument health and support proactive maintenance. Along with 1 sec updates, features include mounting capability up to 1 km away and ability to be configured to reset at unit or remotely via MODBUS, EtherNet/IP, or OPC from host system. Read More

Controls & Controllers, Test & Measuring Instruments

Coriolis Mass Flow Meters feature EtherCAT capability.

April 21, 2015

Suited for research or production processes, mini CORI-FLOW™ ML120 Series Coriolis Mass Flow Meters and Controllers offer flow ranges from 50 mg/h to 200 g/h, with accuracy of 0.2% of reading. Mass Flow Controller features microprocessor-based PC-board with signal and fieldbus conversion, and integrated digital controller utilizing piezoelectric control valve. Meters/Controllers are available with analog and digital communication, RS232, and various fieldbus options. Read More

Test & Measuring Instruments, Controls & Controllers, Sensors, Monitors & Transducers

Turbidity Sensor performs laboratory-quality measurements.

April 9, 2015

Suitable for process water filtration and other industrial process turbidity conditions, Turbimax CUS52D measures turbidity from 0.000–4000 NTU with accuracy of 2% of measurement ±0.01 NTU at process temperatures from -4 to 185°F with detection limit of 0.0015 NTU. Sensor uses 90° light scattering principle in accordance with ISO 7027 standard. Available in immersion, flow cell, and inline versions, Turbimax CUS52D has hygienic design and operates at pressures up to 145 psi. Read More

Sensors, Monitors & Transducers, Test & Measuring Instruments

Compact Liquid Flow Meter serves industrial applications.

March 30, 2015

Delivering measurements for 0–40 ml/min flow rates, SLS-1500 has 20 msec typ response time and can monitor highly dynamic dispensing processes. Modular approach, combining sensor and interface cable, ensures optimal match and accelerated results. Flow channel inside sensor is completely straight and open and has no moving parts, while inert wetted materials provide chemical resistance and biocompatibility. Meter is compatible with SCC1 interface cables. Read More

Test & Measuring Instruments

Variable Area Flow Meters provide 2% accuracy.

March 19, 2015

Employing optimized calibration process with integrated laser engraving system, Lake VA Meters provide precise scale locations and increments directly tied to calibration points on each individual meter. Calibration and scaling process not only streamlines production process, but also improves meter accuracy to 2% of full scale over full flow range. Process is implemented across all VA meter styles, including Basic, High Temp, Pneumatic, and Case Drain meters. Read More

Test & Measuring Instruments, Sensors, Monitors & Transducers

Intelligent Mass Flow Meters offer multi-gas/-range functionality.

March 5, 2015

Supporting 6 gases – N2, Air, O2, Argon, Helium, and CO2 – at up to 8 bar, ZFM offers standard accuracy of ±(0.5% RD + 0.2% FS). Users can, by connecting to RS232/RS485 port of PC or laptop and running ZFM Configuration Utility software, select different gas types and flow ranges (3.5–10 sl/min FS) within minutes and without removing instrument from installation. Other features include automatic sensor zero offset adjustment, 2 programmable totalizers, and selectable analog outputs. Read More

HVAC, Sensors, Monitors & Transducers, Test & Measuring Instruments

Electronic Flow Sensors provide continuous sensing.

February 20, 2015

With measurement ranges from 0.1–60.0 gpm, RotorFlow® Sensors provide accurate switching and clear visual indication within variety of monitoring and metering applications. Paddlewheel design combines high-visibility composite rotors and solid-state electronics. Components are packaged together, within panel-mounted inline housings, with choice of plastic, brass, or steel construction. Some applications include chillers, heat exchangers, medical equipment, lasers, and welders. Read More

Sensors, Monitors & Transducers, Test & Measuring Instruments

In-Line Turbine Flow Meter measures low-viscosity liquids.

February 17, 2015

Featuring flow rate range of 3–26 gpm with ±1% accuracy, MPFM Multi-Purpose Flow Meter is suited for measuring flow of water, detergents, DEF, and other low viscosity liquids. Unit features 2-button interface with ½ in. digits and ability to indicate measurements in gallons, pints, quarts, or liters. Mounted in any orientation, or at end of hose, meter has nylon and glass reinforced fiber body and rotor with ceramic bearings and stainless steel shaft and snap rings for chemical resistance. Read More

Test & Measuring Instruments

Open Channel Area-Velocity Flowmeter has portable design.

February 5, 2015

Capable of monitoring flow through open channels, partially full sewer pipes, and surcharged pipes without flume or weir, MantaRay uses submerged, hydrodynamically shaped ultrasonic sensor that sheds deposits and stringers to promote reliable operation. Flow rate and total are displayed and logged in real-time, and power can be supplied via built-in, rechargeable batteries or external 12–24 Vdc batteries. Included battery charger allows continuous operation with 4–20 mA and relay outputs. Read More

Test & Measuring Instruments, HVAC, Sensors, Monitors & Transducers

In-Line Mass Flow Sensor offers 1-3% accuracy.

January 20, 2015

Based on Microwave Doppler Effect technology, QuantiMass Flow Sensor provides reproducible, non-contact, in-line mass flow measurement of quantities in pneumatic conveying and free-falling processes without use of weigh scales. Unit features sturdy, non-intrusive design that minimizes maintenance. Available with DIN-rail transmitter or local interface controller, sensor is suitable for powders, dust, pellets, and granular up to 0.75 in. Read More

Test & Measuring Instruments, Sensors, Monitors & Transducers

Insertion Meter comes with or without data logger.

January 12, 2015

Designed to measure flow, pressure, and temperature, VPFlowScope is suitable for mobile measurements and fixed installations. Unit offers measuring ranges of 0–500 sfps, 0–250 or 0–500 psi, and up to 140°F. Software can rotate display by 180° and backlighting is adjustable. Basic configuration can be done via display, so laptop is not necessary. Providing Modbus RTU, 4–20 mA, and pulse outputs, meter is suited for compressed air usage measurements, cost allocation, and leakage measurements. Read More

Test & Measuring Instruments, Sensors, Monitors & Transducers

Rechargeable Portable Mass Flow Meters have color display option.

January 12, 2015

Offering ±0.8% reading accuracy for field verification/validation, handheld gas mass flow meters offer multi-parameter measurement and multiple true gas calibrations. Backlit color TFT display provides 6 hr continuous operation for flow verification in low-light settings within environmental, manufacturing, and metrology industries. Along with Gas Select™ firmware, solid-state products feature 5 msec meter speeds and live readouts of mass and volumetric flow rates, pressure, and temperature.
Read More

Test & Measuring Instruments, Fluid & Gas Flow Equipment, Health, Medical and Dental Supplies & Equipment, Sensors, Monitors & Transducers

Oxygen Therapy Products suit people of all ages.

December 29, 2014

Available for adults, toddlers, and infants, Suction and Oxygen Therapy Products come with variety of hospital connections that conform to NFPA 99, ISO, and world standards, including FDA, HCA, and CE. Suction Regulators, offered in analog and digital versions, are suitable for continuous, intermittent, regulating suction, and full suction applications. Medical Air Flow Meters come in flow ratings of 200 cm³ for infants, 1 and 3.5 lpm for babies and toddlers, and 8 and 15 lpm for adults. Read More

Test & Measuring Instruments, Sensors, Monitors & Transducers

Electromagnetic Flow Meters contain no moving parts.

December 19, 2014

Designed for use with conductive liquids in 1–12 in. pipe, FMG980 Series has no moving parts, making it suitable for use in dirty applications where debris would foul mechanical meter. CE-compliant insertion flow meters are also suitable for difficult applications with changing viscosities and pulsating flows, such as air-driven diaphragm pumps. Choice of materials, including stainless steel, brass, and PVC allows meters to adapt to range of temperature, pressure, and corrosive environments. Read More