Advanced Micro Peripherals    New York, NY 10001
May 21, 2012 Converting computer VGA signals into PAL/NTSC/RSI170, NanoVTV is suited for multi-purpose displays in fighting vehicles, illuminated panels, and aircraft/avionics displays. Unit features on-board frame store and DSP unit which performs scan conversion, flicker filtering, scaling, and color space conversion in digital domain. Equipped with board microcontroller, converter can operate completely standalone without run-time control from external system.

Broadcom Corp.    San Jose, CA 95110
Apr 30, 2012 BCM7014 features integrated DVB-C tuner, demodulator, MPEG2 A/V decoder, regulators controller, A/V outputs, and RF modulator. It is designed to facilitate conversion from analog to digital TV reception in India. This cable set-top box system-on-a-chip solution features adaptive volume leveling support that maintains constant volume across commercial, program and channel changes. Conpact size consists of 2-layer reference design measuring 4 x 2.5 in.

PESA Industries, Inc.    Huntsville, AL 35805
Apr 25, 2012 Available in 22 configurations, easyPORT Throw Down Converter Boxes are based on 4-port utility switch, which incorporates standard SFP-type pluggable module card cages that can be populated to support any combination of I/O signals, including HDMI/DVI, 3G-SDI, ASI, NTSC/PAL, and IP-to-ASI conversion. All video formats are transcoded or converted internally, and signals can be distributed over several possible transmission paths, including coax, fiber, and CATx for IP.

For-A    Cypress, CA 90630
Apr 18, 2012 FRC-30 can be switched between motion compensation and linear conversions to deliver optimal results for varying source material. Compensation mode detects motion vector amount of moving object and generates its motion in frames, while linear conversion mode bases frame conversion on previous and next frames. Along with built-in up/down/cross converters, product offers support for several video formats, includes HD/SD-SDI and analog composite I/O, and measures 1 RU high and ½ RU wide.

Analog Bits Inc    Mountain View, CA 94041
Apr 05, 2012 With SERDES IP, customers can use cables with SERDES at either end to recover and retime signal. Pin-configurable macro uses standard CMOS logic process devices and exhibits optimal input sensitivity, jitter tolerance, and equalization. With 0.095 mm² active silicon area per lane, IP is suitable for variety of flip-chip and wire-bound packages embedded in connectors. Serial client interfaces can connect directly to SFPs and operate over frequencies from 125 Mbps to 12.5 Gbps.

iDirect Technologies    Herndon, VA 20171
Mar 22, 2012 With iDX 3.1, organizations can build and support large-scale narrowband networks with existing iDirect Intelligent Platform. Release includes Evolution X1 Remote, which combines low power remote with BUC and LNB, plus DVB-S2/ACM demodulator, TDMA modulator, and VLAN functionality. Evolution X1 Outdoor, featuring IP67 weatherproof housing and passive cooling system, operates from -40 to +60°C. With licensing option, single XLC-M Line Card can support up to 16 narrowband return channels.

NK Technologies    Campbell, CA 95008
Feb 23, 2012 Featuring snap-in installation, CTC Series lets users utilize existing standard 5 A secondary CT or low voltage (0.333 Vac) ProteCT(TM) current transformer with non-contact ranges as low as 0-5 A over conductor to produce standard 4-20 mA, 2-wire, loop-powered signal. DIN rail mounting and 24 Vdc loop-powered supply are standard, and no calibration is required; primary current transformer ratio provides scaling required without any installer intervention.

Monroe Electronics, Inc.    Lyndonville, NY 14098
Jan 19, 2012 Housed in 1 RU chassis, Model R198 converts incoming analog source to digital AES audio and distributes it to 4 different AES switches, making it suited for older Emergency Alert Systems without native AES support and for facilities looking to add digital program streams. With built-in web server, Model R198 can be configured and operated from any standard web browser on any standard platform. Once system is configured, each channel is controllable over TCP/IP network connection or via GPIs.

Weidmuller, Inc.    Richmond, VA 23236
Dec 08, 2011 Available in 8 single- and dual-channel models, ACT20M Series features 2-channel loop-powered isolation, signal splitting with power provided for transmitter, or universal input conversion. DIN-rail mountable, 6 mm wide modules offer option to distribute power through rail, minimizing wiring. With isolation level of 2.5 kV, less than 0.05% accuracy, and ambient temperature range of -13 to 158°F, ACT20M Series is suited for industrial process measurement and control applications.

Analog Devices, Inc.    Norwood, MA 02062-9106
Dec 02, 2011 With full power analog bandwith of 650 MHz, models AD9257 (14-bit) AD9637 (12-bit) octal, along with AD9253 (14-bit) and AD9633 (12-bit) quad A/D converters operate on a single 1.8 V power supply with input voltage range of 2 V p-p. Features include operating temperature range of -40 to +85°C, data and frame clock outputs, serial port control and low power, reduced output swing option. Suitable applications include those requiring low power, small size and high channel density.

Agilent Technologies, Inc.    Santa Clara, CA 95051
Nov 11, 2011 Covering frequencies from 300 kHz to 1.05 THz, PNA and PNA-X Series with frequency converter measurement capability enable engineers to fully characterize mixers and frequency converters up to 67 GHz. Users can measure magnitude-, phase-, and absolute-group-delay response without using reference or calibration mixer. Measurements can be done on devices requiring external local oscillator signals, or those with local oscillators that are not locked to system's 10 MHz reference.

Agilent Technologies, Inc.    Santa Clara, CA 95051
Nov 10, 2011 Using 81199A Wideband Waveform Center software and M8190A arbitrary waveform generator or Infiniium 90000 X-Series oscilloscope, design teams can verify overall performance of 60 GHz wireless devices. Combination also allows validation engineers to perform specific measurements with expected values for transmitters and receivers as defined in standard. Complete solution offers arbitrary waveform creation, frequency conversion, signal modulation, and spectrum analysis.

WAGO Corp.    Germantown, WI 53022
Nov 08, 2011 Simplifying simulators by replacing standalone frequency generators, rotating equipment, and associated cabling, 0-10 Vdc 859 Series mimics motor encoders to generate pulse inputs for controlling lighting or machine speed. Products can be factory-tuned to user-specified frequency within 3 ranges: 0-1.0, 0-1.5, or 0-25 KHz, and isolated versions are available for excessively noisy environments or applications with high potential differences between machinery.

JH Technology, Inc.    Sarasota, FL 34233 2432
Oct 24, 2011 Models JH7500/JH7501 plug into standard relay sockets and feature I/O isolation as well as AC or DC power options. Model JH7500 offers output ranges to 10 kHz, and Model JH7501 has relay contact output for electromechanical counters (FS pulse rates can be as low as 1.25 pulses/min). Range of input choices includes standard process signals such as 0-5 V, 0-10 V, 4-20 mA, and 0-1 mAdc as well as others.

Pentek Inc.    Upper Saddle River, NJ 07458
Oct 20, 2011 Based on Xilinx Virtex-6 FPGA preconfigured with data acquisition and playback IP, Cobalt(TM) 71651 has 2 input and 2 output RF channels, transformer-coupled to allow direct connection to HF or IF radio stages. Input channels feature 12-bit, 500 MHz A/Ds that feed data into Virtex-6 FPGA, while output channels incorporate TI DAC5688 digital upconverter that translates baseband signals to IF frequency up to 380 MHz. Dual 16-bit, 800 MHz D/As create real or in-phase and quadrature analog outputs.

Electro Standards Laboratories    Cranston, RI 02921 3403
Oct 05, 2011 With integrated rate buffering, Model 4149 (desktop), Model 4149-DIN, and Model 4159 (board) operate from -40 to +85°C with typical speeds to 1.5 Mbps for RS232 to fiber conversion and up to 5 Mbps for RS485/422 to fiber conversion. Model 4149-DIN provides enclosure and all mounting hardware and brackets for installation in DIN-rail application. Model 4159 features front-mounting threaded brackets for rack mounting in embedded applications.

Data Device Corp. (DDC)    Bohemia, NY 11716-2482
Oct 05, 2011 Providing up to 4 independent channels, SB-36330CX can be configured for 11.8 V line-to-line synchro/resolver, 90 V line-to-line synchro, or 2 V sin/cos signal input, with 10, 12, 14, or 16-bit resolution. Each channel provides separate reference input which is auto-ranging to accept reference signal from 2-130 Vrms. Operating over industrial temperature range of -40 to +85°C, Model SB-3633CX includes AquadB encoder emulation outputs for motor control applications.

Motor Protection Electronics, Inc.    Apopka, FL 32703
Sep 06, 2011 Powered by 24 Vdc, LPC420 senses liquid level and provides 4-20mA analog output for use by pump controller or PLC in liquid level control applications. All setup is done using 4 DIP switches on unit, and sensitivity is set for type of liquid being detected. Analog output delay setting controls how fast analog output transitions from one level output value to another. Supplied in aluminum enclosure, DIN rail mountable unit has no openings through which debris can enter.

Automation Systems Interconnect Inc.    Mechanicsburg, PA 17055
Aug 15, 2011 Available from 0-1 A to 0-10 A, Current to Analog Converters allow user to monitor flow of current in circuit indicating circuit is operating and load is connected and active. Use of Hall Effect sensor enables both AC and DC currents to be measured. Since 3 different common analog outputs are available, modules will work in any control application where current to analog signal conversion is required.

Omega Engineering, Inc.    Stamford, CT 06907
Aug 11, 2011 PCM5 series converts 4-20 mA signal from process/temperature controller or computer to time proportional output. Mounted directly on single 3-32 Vdc Input SSR, module supports single-phase, 50 or 60 Hz operation and tolerates inputs of less than 4 mA. In manufacturing environment, series is used with process controller and solid state relay to control electric heaters for oven drying manufactured parts. Other areas of use include water, chemical, automotive, and food processing industries.