Test & Measuring Instruments ->
Instrumentation I & O Devices|
Instrumentation I & O Devices
(Showing headlines 1341 - 1360) << 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 ...
Commutation Encoder features 120°C temperature rating.
Gurnee, IL 60031
Aug 04, 2008
With low profile that enables mounting onto stepper and servo motors, M53 modular commutation encoder has direct-read phased array ASIC that provides 2,500 ppr. It comes with commutation tracks for 4, 6, or 8 pole brushless motors, and uses built-in gapping mechanism that requires no special tools or parts that can get lost or damaged. With ability to accommodate motor shafts from ¼ to ½ in. including metric sizes, encoder is suitable for use with variety of motors.
I/O Modules enable structural test of PCI express slots.
GOEPEL electronics LLC
Austin, TX 78759
Aug 04, 2008
Able to completely test PCI Express Standard V2.0 compliant slots via dot1/dot6 for correct pin contacting, IEEE Std. 1149.6 compliant CION Module(TM)/PCIe-x(1/4) interface cards are plugged directly into x1 or x4 PCI Express slot and controlled by TAP (Test Access Port). With on-board IEEE 1149.1 and IEEE 1149.6 test channels, all high speed signal pins, low speed signal pins, and voltage supply pin of PCI Express compliant connectors can be tested structurally.
I/O Terminals use eXtreme Fast Control(TM) technologies.
Beckhoff Automation LLC
Minneapolis, MN 55337
Aug 01, 2008
EtherCAT® I/O terminals with time stamping latch exact system time at which edge changes occur; digital value output can occur at predefined times. Terminals with oversampling enable actual value acquisition or set value output with higher time resolution than communication cycle time. Distributed clocks with less than 1 µsec jitter and 1 µsec resolution are used for time synchronization across entire system. Fast I/O-enabled terminals offer input delays/switching times under 1 µsec.
Switching Multiplexer can be supported by any 3U PXI chassis.
Wobum, MA 01801
Aug 01, 2008
With POTS, USB 2.0, AFDX, and Gigabit Ethernet capability, Model 40-736 can switch communications signals carried on 100 W differential pair cables. It is configured as 8:1 or 16:1 multiplexer for GbE and 100BaseT/AFDX applications, respectively. I/O signals are carried on 78 way D Type connector, while interface adaptor card converts signals to 8:1 Ethernet MUX on RJ45 connectors for direct connection to Ethernet cable.
CML Output ICs operate up to 3.2 GHz.
Micrel Semiconductor Inc.
San Jose, CA 95131
Aug 01, 2008
Series SY54xxx includes 7 low voltage CML output products with core power supply of 2.5 V that can interface directly to devices powered by 1.2/1.8 V supply. Products include 1:2 fanout buffer, differential line driver/receiver, 2:1 multiplexer, and 2 x 2 crosspoint switch. AC performance is guaranteed from dc through 2.5-3.2 GHz or 3.2 Gbps, with rise and fall times of less than 95 ps. Jitter performance is less than 10 ps p-p over temperature and voltage.
Web-Based Tool grants remote access to press information.
Greenerd Press & Machine Co., Inc.
Nashua, NH 03061
Jul 31, 2008
Using pressport private online network, customers can obtain real-time status of hydraulic press operations and view data by logging in via Ethernet connection. Customers can also receive status/alarm notifications on internet-enabled devices such as cell phones, smart phones, or PCs. Anywhere, 24/7 access promotes immediate response to any problems with manufacturing process, and FTP feature offers ability to send/receive data from pressport and customize data structure.
Wireless DAQ System function over 20 mile range.
Wilkerson Instrument Co., Inc.
Lakeland, FL 33811
Jul 31, 2008
System provides analog and contact inputs with analog and discrete outputs for point to point data acquisition. Wireless transmitter (DR9011) sends analog and contact closure data to companion DR9021, where it is recovered as two 4-20 mA outputs, and switch data is provided by optically isolated NPN transistors outputs. RF choices - 2 in 915 MHz ISM band and 1 in 2.4 GHz band - all use spread spectrum frequency hopping technology. Each RF module has choice of 7 Hop sequences.
SPI and I2C DACs integrate precision reference.
Linear Technology Corp.
Milpitas, CA 95035
Jul 30, 2008
Supplied in 8-pin TSOT-23 package, LTC2631 I²C DACs are suited for fine tuning bias voltages. They incorporate 10 ppm/°C reference output, available to drive reference inputs for all other data converters on board. Also available, LTC2640 SPI DACs offer choice of 2.5 or 4.096 V FS output range. External reference can be applied if more accuracy or non-standard voltage range is required. Both series include 8-, 10-, and 12-bit models that draw 180 µA supply current at 3 V.
RF Module offers direct analog input.
Saelig Co., Inc.
Pittsford, NY 14534
Jul 30, 2008
With 4 analog inputs, EmbedRF(TM) can directly interface with voltage-output sensors and transmit information up to 50 ft. Miniature wireless board offers bi-directional transmit/receive point-to-point and point-to-multipoint capabilities. Measuring 0.8 x 0.7 in. and less than 0.2 in. thick, module provides output power up to 5 dBm at frequencies from 400-928 MHz. It includes on-board antenna, intelligent search, and 24-bit security capabilities.
Sensor Interface Board is compatible with H7546B MAPMT.
Westford, MA 01886
Jul 28, 2008
Model SIB164 provides mechanical and electrical interface between Hamamatsu H7546B 64-anode photomultiplier tube (PMT) and 64 channel DAQ system. Charge signals from high-speed events are detected by PMT mounted on SIB164 and sent over specialized cables to DAQ system. When used with IQSP582 PhotoniQ system, SIB164 achieves single photon sensitivity at rates exceeding 200,000 events/sec. Board also incorporates last dynode preamplifier and 3 types of on-board pulse discriminators.
Portable DAQ System is optimized for throughput.
Pacific Instruments, Inc.
Concord, CA 94520
Jul 28, 2008
Powered via DC or battery, Model 6005 has 10-slot enclosure that accepts Series 6000 transducer signal conditioning and DAQ modules. Connectors and controls are located on front to promote access in tight spaces, while USB 2.0 and Ethernet interfaces promote data throughput rates to 4 MSPS. Solution plugs into laptop computer with Windows XP/Vista and PI660 acquisition and display software. Optional on-board rotating or solid-state drive is also available.
Plug-In Cards expand system switch/multimeter functionality.
Keithley Instruments, Inc.
Cleveland, OH 44139 1891
Jul 28, 2008
Model 3724 Dual 1X30 FET Relay Multiplexer Card offers scanning speeds over 1,000 channels/sec, including measurement, and switch-only scan rates over 1,200 channels/sec. Solid state relays can be automatically configured into dual 1 x 30 or 1 x 60 multiplexer. Gated with 1 MHz input rate, Model 3750 Multifunction I/O Card features 40 DIO channels with high-current driver outputs that sink up to 300 mA. Other features include 2 programmable analog outputs and 4 totalizers/counters.
I/O Carriers feature vertical orientation.
Emerson Process Management
Austin, TX 78754
Jul 24, 2008
Optimizing airflow and thermal management, DeltaV(TM) VerticalPlus I/O Carriers support simplex and redundant DeltaV SIS modules that communicate via redundant safety bus, which is separate from basic process control system communications. Carriers can also communicate secure SIS data via redundant SISNet Repeaters to other DeltaV SIS nodes on vertical and horizontal carriers. Featuring modular design, carriers can be added as needed and only require T-type DIN rail for mounting.
Synchro/Resolver Simulation Card has programmable channels.
North Atlantic Industries, Inc.
Bohemia, NY 11716
Jul 23, 2008
On one 3U cPCI card, DSP-based 75DS2 includes up to 4 independent, isolated, programmable Synchro/Resolver or LVDT/RVDT simulation channels. Each has 16-bit resolution, ±1 arc-min accuracy, and short circuit protected output with 1.5, 2.2, or 3.0 VA drive capability. Requiring +5 and ±12 Vdc power supplies, product operates over 47 Hz to 10 kHz range. Each unit also includes wrap-around self-test, programmable output angle rotation, and optional 3 VA programmable reference supply.
Absolute Encoder features 13 bits/turn resolution.
BEI Sensors (BEI Industrial Encoders)
Goleta, CA 93117
Jul 23, 2008
Housed in 1.8 in. servo package with all-metal housing, optically based Model L18 contains field-proven ASIC electronics, sealed bearings, and accurate code disk. Unit is suited for space or weight limited applications requiring high accuracy, including semiconductor fabrication, industrial robotics, and mobile platforms.
Analog Multiplexers and Switches have low leakage currents.
Vishay Intertechnology, Inc.
Malvern, PA 19355 2143
Jul 23, 2008
Suited for precision instrumentation applications, DGxxx Series includes 4 analog multiplexers and 4 analog switches that combine charge current from 0.5-1.0 pC, switch capacitance of 2 and 3 pF, leakage currents from 0.25-5 nA, and typical on-resistance from 66-72 W. All operate from 2.7-12 V single supply or from ±2.5 to ±5.0 V dual supplies. Available in variety of packages, devices feature extended operating temperature of -40 to +125°C.
Weld Wire Monitor features automated operation.
Elco Enterprises, Inc.
Jackson, MI 49201
Jul 21, 2008
Utilizing wire feed sensor and controller, Wizard View(TM) Wire Central DAQ System monitors critical welding wire usage information - quantity left in drum, speed of travel - measured in US or metric units. Elimination of constant manual inspections automates weld wire usage information monitoring. Alerts notify operator when wire has stopped moving, when pre-set amount of wire is left in drum, and when wire is not within programmable wire feed speed window limits.
GPS Simulation System is optimized for testing capability.
Spirent Communications plc
Crawley United Kingdom
Jul 21, 2008
Suited for demanding applications, Spirent GSS8000 supports up to 20,000 G signal dynamics, up to 120,000 m/s velocity, and 50 Hz processing rates. Motion data can be generated via on-board vehicle models or real-time high-rate host vehicle trajectory data over remote interface. Low-latency hardware-in-the-loop capability is standard with synchronization and timing facilitated via 1 PPS in/out and 10 MHz clock inputs. Implementation supports full 6 degrees-of-freedom trajectory data.
I/O Modules offer complete BACnet® solution.
Contemporary Controls Ltd
Coventry West Midla CV4 7EZ United Kingdom
Jul 17, 2008
BASR-8M BAS Remote Expansion Modules can be daisy-chained together to BAS Remote Master (BASR-8M) to meet specific I/O requirements, and BASR-8M can be expanded to total of 32 Universal I/O points and 8 relay contacts to suit any building automation installation. Configurable Universal I/O can support BACnet®/IP or Modbus/TCP points, and digital inputs can accept pulse trains in range of 0-40 Hz at 50% duty cycle to measure flow rates.
Process Controller is designed for DC electric fastening.
Stanley Assembly Technologies
Cleveland, OH 44143-2328
Jul 16, 2008
Compatible with Stanley® QPM DC electric tools from 0.6-2,000 nm, QA Alpha can link multiple parameter sets in sequence for tightening different fasteners in workstation. It features Embedded Toolbox software, Ethernet for message-based protocols and fieldbus I/O mapping USB Port, and 2 COM ports, one connecting computer and enabling remote configuration, and one for adding barcode reader, printer, or other serial device. I/O controller options include 24 V, fieldbus, and Modbus TCP.
(Showing headlines 1341 - 1360) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161