Dwyer Instruments, Inc.    Michigan City, IN 46361
May 09, 2012 Combining individual pressure gauge and thermometer in one instrument, Series TRI2 features moveable dial with blue pressure markings and red temperature markings. Internal Bourdon tube assembly indicates pressure in both psi and kPa, while bimetal coil assembly measures temperature in both °F and °C. Available in rear and lower connect models, gauges are suited for use on boilers and other hot water applications where space is limited.

CorDEX Instruments Ltd.    Scarborough YO139QD  United Kingdom
May 09, 2012 Used for non-destructive testing to establish extent of corrosion, intrinsically safe UT5000 uses Echo-Echo technology to read metal thickness levels even through painted surface. Intelligent measuring technology can record multiple readings at specific locations, and total of 9 multi-point readings can be saved against each RFID tag on asset or pipeline. Dual-element, 4 MHz transducer is adjustable up to 10 Hz and offers accuracy of ±0.05 mm.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Mar 12, 2012 Constructed with 304 stainless steel housings and brass wetted parts for chemical compatibility, Series SGY offers wide variety of ranges from full vacuum to 1,000 psi. Units have dual psi and bar scales and are available with bottom or back connections. Designed to pop open without being entirely removed or cut, plug on top allows liquid filled units to breath, relieving any built up internal pressures.

Mark-10 Corp.    Copiague, NY 11726
Mar 02, 2012 Applying up to 200 lbf, Model WT3-200 measures pull-off force of wire and tube terminations. Backlit graphic LCD displays real-time force, peak force, and programmable pass/fail limits. Data can be transferred to PC or other data collector via USB, RS-232, Mitutoyo, or analog outputs. Able to store 1,000 readings and calculate statistics, tester includes break detection feature that can be configured to automatically output data, store data, and zero display upon sample break.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Feb 29, 2012 Designed for continuous measurement of powder and bulk materials in silos, tanks, or hoppers, Series DBOB utilizes internal motor that drives weight suspended by firm stainless steel tape down to bulk material level. Upon reaching material, unit reverses and weight is drawn back into upper stop position. Distance weight descends is electronically measured based on internal rotations of unwinding tape. User-programmable to output height or volumetric signal, device measures at rate of 0.6 fps.

Macro Sensors    Pennsauken, NJ 08110 1334
Feb 28, 2012 Available in 3 standard ranges of +0.020, +0.100, and +0.200 in., BB Series LVDT dimensional gaging probes combine AC-LVDT with linear ball bearing assembly to reduce radial play and core skewing, resulting in repeatability of 0.000006 in. Spring-loaded LVDTs feature rubber bellows covering probe shaft to prevent contaminants from entering into bearing. Probes are available in 4 models including full bridge, half bridge, pneumatic and soft touch.

Fluke Corp.    Everett, WA 98203
Feb 07, 2012 Fluke® 700G Series Precision Pressure Test Gauges can measure -14 to 15 psi with resolution of 0.001 psi (model 700G04) to -14 to 10,000 psi with 1 psi resolution (model 700G31) with 0.05% total measurement uncertainty for one year. Equipped with backlit display, instruments can log up to 8,493 pressure measurements when used in conjunction with 700G/TRACK software and feature ¼ in. NPT to ¼ in. ISO adapter for connections. Products carry CSA and ATEX approvals.

Omega Engineering, Inc.    Stamford, CT 06907
Feb 02, 2012 Based on micro-machined silicon sensor with 0.08% accuracy, Model DPGM409 covers full spectrum in pressure measurement with gage, sealed gage, absolute, compound gage, vacuum, and barometric ranges. User selectable analog output of 0-5 Vdc, 0-10 Vdc, or 4-20 mA is standard, and built-in wireless transmitter is optional. Enclosed in washdown-rated stainless steel and ABS housing, battery-powered gauge has 1 in. digits and front panel programmable MIN/MAX/AVG readings.

Essemtec Ag      Switzerland
Feb 01, 2012 Available as option on FLX2011 Series machines, placing force measurement system consists of chuck where actual placement takes place. Chuck allows for processing of substrates such as PCBs with max size of 200 x 200 x 3 mm. By means of software plug-in, actual placement force from 0-5 N ±0.5 N can be predefined. Spring characteristic is calibrated for each nozzle and data is stored in database.

Polygon Solutions, Inc.    Fort Myers, FL 33912
Dec 20, 2011 Made of hardened M-2 tool steel, Rotary Broach Gauges ensure size of hexagon or square hole has been machined properly. Each gauge is held by hand and inserted into hexagon or square hole. If NOGO gauge fits, hole is too large and part fails inspection. If GO gauge fits, hole size is correct and part will pass. Gauges can also help determine if there is too much twist in form, which is common with holes manufactured using rotary broaching process.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Dec 16, 2011 Supplied with 304 SS housings and 316 SS wetted parts for chemical compatibility, 1.5 in. Series SG3 and 2.5 in. Series SGZ feature dual psi and bar (x100 kPa) scales with respective ±2.5% and ±1.5% FS accuracy. Series SG3 covers ranges from full vacuum to 300 psi and can withstand ambient temperatures to 140°F. Bottom or back 1/8" NPT connection options are available. Equipped with breather plug, Series SGZ also covers diverse ranges and offers bottom or back connection configurations.

Palmer Wahl    Asheville, NC 28804
Dec 14, 2011 Featuring 2.5 in. dial face, EDG Gauges display pressures on LCD with ±1% FS accuracy and settable resolutions of 0.1, 0.2, 0.5, and 1 whole unit. Units operate on 9 V battery for approximately 1,500 hours, and include auto-off timer that saves battery life, allowing gauges to be always on, or to auto shut off in increments from 30-180 sec. Equipped with protective rubber boot and ¼ in. bottom NPT connection, gauges are available with 316 SS internals for corrosive liquid applications.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Dec 07, 2011 Providing both low and high limit control, Series AT23000MR and AT23000MRS Photohelic® Switches/Gauges combine differential pressure switch with analog pressure gage. AT23000MR Series employs electromechanical relays, while AT23000MRS Series uses SPST (NO) solid state relays. Compatible with air and other non-combustible, non-corrosive gases, gauges handle pressures to 25 psig. Flame-proof ATEX enclosures have glass window for viewing set point needles and process pressure.

Mahr Federal Inc.    Providence, RI 02905
Dec 02, 2011 MarSurf® M 400 features motorized probe height adjustment that automatically zeros probe in seconds. Magnetic breakaway probe mounting system protects probes from accidental damage and facilitates changes. System measures all common international parameters and features Bluetooth connectivity between measuring system and evaluation unit with integrated thermal printer. Skidless tracing of surface characteristics allows capture of primary, waviness, and roughness profiles.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Dec 01, 2011 Designed for critical low differential pressure applications, Series RSM can be configured to monitor positive or negative pressure in protected environments and hospital isolation rooms per CDC guidelines. System includes backlit LCD with GUI that enables access to pressure, security, calibration, and alarm setup. LEDs and local audible alarm alert personnel to system status. Made of NEMA 1 rated fire retardant plastic, monitor displays true differential pressure with 0.001 in. wc resolution.

Adcole Corp.    Marlborough, MA 01752-3067
Nov 04, 2011 Capable of high-speed production monitoring of up to 200 parts/hr, ADCOLE 1310 measures 10 or more parameters, including radius, profile, taper, crown, timing angle, diameter, velocity, acceleration, run-out, roundness, and concentricity. End-of-line gauge provides 0.1 micron resolution per data point. Incorporating Eurocard PCB format with diagnostic test points in front, gauge comes equipped with dual computers, Windows XP® embedded software, and GE Fanuc® motion controllers.

AutomationDirect.com    Cumming, GA 30040-9905
Nov 01, 2011 Using Bourdon tube sensing elements to measure vacuum to 6,000 psi, ProSense(TM) Pressure Gauges come in steel or stainless steel, in dry or liquid filled versions to dampen vibration and pulsations. Brass wetted parts are suited for air, oil, or water, while stainless steel wetted parts are offered for corrosive applications. Constructed of 304 SS with bi-metal sensing elements, ProSense(TM) Thermometers are available in 3 in. dials with center back mounts and 5 in. dials with adjustable angle mounts.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Oct 24, 2011 Available with bottom or back connections, 1.5 in. Series SG1 Industrial Pressure Gauge features dual psi and bar scales with ±2.5% FS accuracy. Units are constructed with brass connector, bronze tube, polycarbonate lens, and stainless steel case and ring, which offer protection from harsh processes. Operating from -4 to 140°F, gauges are suitable for applications where ambient corrosion and vibration are of concern.

Paul N. Gardner Co., Inc.    Pompano Beach, FL 33060 6608
Oct 12, 2011 Along with backlit display and 1 m sensor cable, battery-operated MiniTest 650 features one-pole sensor made of wear-resistant carbide material. Ram- and impact-protection is provided through rubber rimmed casing, and USB interface enables connection to PC. Unit comes in 3 models: with magnetic-induction sensor for measurements on steel substrates; with eddy currents sensor for measurements on non-ferrous metals; and with dual sensor for measuring on both steel or non-ferrous metals.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Oct 07, 2011 Comprised of repeatable pressure switches combined with precision pressure gauge, Series AT3A3000 employ Magnehelic® gauge design and come in flame-proof enclosure. ATEX-approved Photohelic® switch/gauge products measure and control positive, negative, or differential pressure of air and compatible gases. Standard models are rated to 25 psig, with options to 35 or 80 psig. All feature phototransistor-actuated, DPDT relays for low/high limit control and adjustable set point indicators.