McCrometer, Inc.    Hemet, CA 92545
May 11, 2012 Suited for gas or liquid service in line sizes from 1-6 in., Wafer-Cone® Flowmeter features flangeless design and plug-and-play mounting, eliminating potential source of flow measurement errors. Unit uses differential pressure sensing technology with built-in flow conditioning, achieving accuracy of +1.0%, with repeatability of +0.1%, and operation over flow range of 10:1. When flow conditions change over time, cone can be removed and replaced with cone at different beta ratio.

Bronkhorst High-Tech BV    NL-7261 AK   Netherlands
May 08, 2012 Promoting accelerated analysis while minimizing requirements for reagents and analytes, LIQUI-FLOW mini measures flow ranges from 1.5-75 mg/h up to 12-600 mg/h as based on water. Straight duplex steel sensor tube has internal volume of less than 1 mm³ and operates on thermal measuring principle. Suited to HPLC systems and rated for pressures to 1,000 bar, compact instrument features MPU-based PCB and RJ45 connection for power supply as well as analog and digital (RS232) communication.

ABB Instrumentation    Warminster, PA 18974
May 04, 2012 Designed to work with both WaterMaster and AquaMaster 3 transmitters, AquaProbe offers choice of main- and battery-power options as well as renewable power version, which can draw power from solar or wind power. Unit fits pipe sizes from 200-8,000 mm and is fully submersible with IP68/NEMA 6P protection rating. Installed using fit-and-flow intelligent technology, which eliminates need to match flow sensor and transmitter in field, flowmeter is suited for clean water applications.

L & J Technologies, Inc.    Hillside, IL 60162
Apr 19, 2012 Comprised of wave guide, probe housing, float with permanently-embedded magnets, and motion or stress sensing device, MCG 8151 gathers level gauging information, can act as point switch for overfill alarms, and has 5 temperature sensors to provide average temperature measurement of product. Offering resolution of ±.001 in., MCG 8151 is available in lengths up to 70 ft and can be installed in nearly any type of storage or process vessel, aboveground or underground.

Fluid Components International    San Marcos, CA 92069
Apr 11, 2012 Thermal Mass Air/Gas Flow Meter, ST100 Series, suits equipment-crowded plants or hazardous factory areas where combustible or toxic gases may be present. Using interconnecting cable, transmitter with optional digital display can be mounted up to 1,000 ft away from flow sensor. Product continuously measures, displays, and transmits array of parameters and is available with 4-20 mA analog, frequency/pulse, alarm relays, or digital bus communications: HART, Fieldbus, Profibus or Modbus.

Clark Solutions    Hudson, MA 01749
Apr 11, 2012 Designed for 3 and 4 in. pipe systems, FSI-S00 is constructed with 4-bladed, HDPE impeller; Type 1 PVC sensor housing; tungsten carbide impeller shaft; and BUNA-N O-ring. Sensor is rated to 150 psi and outputs square wave digital signal proportional to flow. Also, pulse signal output will travel up to 2,000 ft without amplification. Installation requires end user to drill pipe and mount saddle, and sensor insert mounts in housing that controls depth and alignment of impeller.

Clark Solutions    Hudson, MA 01749
Apr 11, 2012 Designed for 1, 1½, and 2 in. pipe systems, FSI-T00 Series is constructed with 4-bladed HDPE impeller, Type 1 PVC sensor housing, tungsten carbide impeller shaft, and Buna-N O-ring. Units deliver square wave digital signal output proportional to flow that will travel up to 2,000 ft without amplification. Equipped with threaded retaining nut for servicing, sensors are suited for water treatment systems, water dispensing, cooling loops, irrigation systems, and large scale aquariums.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Apr 04, 2012 Supplied pre-calibrated for horizontal, inline mounting, Series DTFW is available with brass or 316 stainless steel body to withstand system pressures up to 3,000 psig. Ranges are offered up to 30 gpm, and products measure water flow rates with ±2% FS accuracy. Available with ¼, ½, and 1 in. connections, series features 2.5 in. dia dial face. Other elements of construction include 302 SS spring and range spring, PTFE-coated magnet, acetal or PTFE metering cone, and Buna seals.

BlueLevel Technologies, Inc.    Rock Falls, IL 61071
Mar 12, 2012 With overall insertion length from 18-118 in., Model VHS is suited for top mounting installations where advantages of no calibration and solid-state technology are desirable. Sensor, utilizing piezoelectric technology, will operate with dry and free-flowing powders as well as free-flowing granular materials. Unit has built-in SPDT relay that is fail-safe on power failure, local bi-color LED indicator of normal/alarm status, all stainless steel wetted parts, and NEMA 4X enclosure.

Fluid Components Intl.    San Marcos, CA 92069 5115
Mar 09, 2012 With VeriCal Calibration Verification System, ST100 Series combines advanced measurement capability with in-situ calibration for flare gas applications aboard offshore platforms, land-based oil/gas facilities, and chemical plants. Basic insertion style air/gas meter features thermal flow sensing element that measures flow from 0.25-1,000 SFPS with accuracy of ±0.75% of reading, ±0.5% of full scale. Designed for service up to 850°F, meter is available with integral or remote electronics.

Honeywell International, Inc.    Morristown, NJ 07960
Mar 07, 2012 Providing flow ranges from ±50 to ±750 SCCM, Zephyr(TM) Analog and Digital Airflow Sensors offer Total Error Band as low as ±2.25% FSS, allowing accurate airflow measurement. Stability minimizes errors due to thermal effects and null shift, providing accurate readings over time and often eliminating calibration after PCB mount. Potential applications include fuel cells, gas meters, and HVAC filters as well as hospital diagnostics, patient monitoring, and ventilators.

Baumer Ltd.    Southington, CT 06489 1534
Mar 05, 2012 Able to detect media levels in tanks, vessels, and pipes, LBFS level switch features sensitivity over measuring range for dielectric constants from 1.5 to 100+ that enables limit detection with all types of powders, granulates, and liquids. Response time of 0.2 sec promotes accelerated fill level detection as well as fill level accuracy and compliance. Featuring sensor head resistant to media adhesion, product is insensitive to flow, turbulence, bubbles or foaming, and suspended solids.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Feb 29, 2012 Designed for continuous measurement of powder and bulk materials in silos, tanks, or hoppers, Series DBOB utilizes internal motor that drives weight suspended by firm stainless steel tape down to bulk material level. Upon reaching material, unit reverses and weight is drawn back into upper stop position. Distance weight descends is electronically measured based on internal rotations of unwinding tape. User-programmable to output height or volumetric signal, device measures at rate of 0.6 fps.

POSIFA Microsystems Inc    San Jose, CA 95112
Feb 28, 2012 As drop-in, pin-compatible upgrade to Honeywell AWM3000 series, PMFc3000 series incorporates MEMS and microelectronics technologies and replaces membrane-cavity structure with solid-state thermal isolation process. This promotes reliability by eliminating field failures associated with pressure shock and contamination. While meeting same packaging and calibration specifications of AWM3000, PMFc3000 series offers initial output tolerance to less than 2% FS.

Honeywell Sensing and Control    Golden Valley, MN 55422
Feb 24, 2012 Housed in IP67-sealed package with integral connector, RTY Series Rotary Position Sensors provide 12 million cycle product life and 8 operating ranges up to 360°, which are tolerant to over-travel. Low and high voltage versions cover input voltage range of 4.5-30 Vdc. Providing non-contact operation, sensors use magnetically biased, Hall-effect IC to sense rotary movement of actuator shaft over set operating range. Devices are protected against both reverse polarity and EMI.

FMC Technologies Inc. Measurement Solutions    Erie, PA 16514
Feb 09, 2012 Immune to external piping forces, Proline® Promass E Coriolis flowmeter is available in 3/8-3 in. sizes for use in liquid or gas measurement and operates from -40 to +284°F. Fit-and-Forget installation eliminates need for long lengths of straight pipe runs or supports/braces for meter. Meter is supplied with model 83 transmitter, which offers 4-line LCD with touch control operation, application-specific quick setup, and measurement display.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Feb 08, 2012 Available in either ¼ or ½ in. NPT connections with ranges up to 100 scfm, Series DTFA offers ±5% FS measurement accuracy and ±1% FS repeatability. Flowmeter features 2.5 in. dia dial face and is constructed with aluminum body to withstand system pressures up to 3,000 psig. Reliability is further promoted via PTFE-coated spring and magnet, 302 SS range spring, acetal metering cone, and Buna seals. Pre-calibrated for horizontal in-line mounting, product has -40 to +200°F temperature limit.

Climatecraft    Oklahoma City, OK 73101
Feb 06, 2012 MatrixMonitor(TM) gauges airflow in arrays with 3-98 fans, with max airflow of 300,000 cfm per array. Offering alternative to fan inlet and piezometric flow monitors, this digital instrument consists of sensors and internal wiring for each fan connected to embedded processor. Solution operates on 100 W power supply and generates one airflow signal for entire fan array. With dual fan array capability, product can operate as stand-alone system or integrate with building automation system.

TR Electronic, Inc.    Troy, MI 48083
Feb 06, 2012 By inductively supplying power and signals from fixed part to moving part, across air gap, PowerGap(TM) eliminates need for cables, connectors, and slip ring solutions. System features wear-free, non-contact design, which can transmit wirelessly through non-metallic barriers. Available in Standard M18, M30, and 90 x 90 mm square housings, PowerGap has up to 64 inputs and 32 outputs of discrete I/O and is DeviceNet, EtherNet/IP, and RS232 compatible.

Macro Sensors    Pennsauken, NJ 08110 1334
Jan 20, 2012 Environmentally sealed to IP68 standard, rated to 185°F, and protected against dust ingress, Steel Mill Position Sensors monitor position of milling frames that support rollers during hot rolling process, ensuring frames do not deform or shift. Radial configuration with rod ends facilitates installation, while pre-calibrated on-board electronics eliminate need to configure signal conditioners. Available in ±0.015 to ±10.0 in. ranges, non-contact sensors provide 0-10 V, 4-20 mA, and ±10 V outputs.