Safety & Security Sensors & Detectors

Electrical Equipment & Systems, Sensors, Monitors & Transducers

Safety Disconnect Switch features stainless steel enclosure.

March 24, 2015

Housed in non-magnetic Type 304 stainless steel enclosure, Powerswitch® MDS30-AX is rated at 30 A and 600 V. Non-fused safety disconnect switch is watertight and dust-tight with IP66/IP67 and NEMA Type 3R, 4X, and 12K ratings. Mounting feet stand ¾ in. from wall to enable inspection and cleaning behind unit. Made from polycarbonate, high-impact, non-conductive handle features 3 provisions for padlocks to comply with OSHA lockout and tagout capabilities. Read More

Transportation Industry Products, Sensors, Monitors & Transducers

Back-Up Alarm alerts truck drivers to obstructions, incidents.

March 3, 2015

Designed for large trucks and haulers, wireless and commercial-grade RVS-114 makes roads safer for commercial and passenger vehicles. Mounted to rear of vehicle, 4 sensors monitor events occurring at rear of vehicle. Sensors connect to control box, connected from outside/inside via wireless technology, to display placed on front of vehicle. Visual and audible warnings alert drivers of any and all hazards that may exist behind their vehicle and eliminates blind spots. Read More

Electrical Equipment & Systems, Sensors, Monitors & Transducers

Safety Limit meets regulatory requirements.

February 25, 2015

Approved to UL® 1998 and EN 60730 as well as WEEE, CE, and RoHS standards, SERIES LS will shut system down to prevent damage to equipment or injury to personnel. Device maximizes safety by using factory fixed set point, factory fixed hysteresis, and redundant temperature sensors to protect against single-point sensor failure. Uses include applications where control failure could cause temperature to continue to increase and cause damage to system, potential fire hazard, or product scrap. Read More

Electrical Equipment & Systems, Sensors, Monitors & Transducers

Magnetic Safety Switches feature integrated LED indicators.

February 10, 2015

Featuring tamperproof design, SMA Series provides contactless safety monitoring of machine doors. Integrated LED technology gives machine operators immediate indication of safety door's interlock status to minimize incidence of unscheduled downtime. Rated for 48 Vdc/0.2 A, interlock switches feature NO/NO/NC contacts with actuating distance of 7–20 mm. SMA 0249 models are designed with M12 connector, while SMA 0243 devices have 3 m open-wire cable integral to unit. Read More

Health, Medical and Dental Supplies & Equipment, Safety & Security Equipment, Sensors, Monitors & Transducers, Non-Industrial Products

Waterproof Sensor Pads help maximize patient safety.

January 27, 2015

Part of Sensatec® Fall Management Solution, bed and chair sensor pads are antimicrobial and reusable. Pads connect with universal 4-pin connector compatible with all 600 Series Sensatec alarm units. Made of non-slip, latex-free materials, products can be completely submerged and cleaned with germicidal bleach-type solutions for optimal infection control. Typical applications include hospitals, rehabilitation facilities, and senior living communities. Read More

Test & Measuring Instruments, Vision Systems, Software, Sensors, Monitors & Transducers, Communication Systems & Equipment

X-Ray Screening System aids anti-terrorism efforts.

January 5, 2015

Linked to any X-ray machine used to screen for prohibited items, SecureTech™ instantly transmits suspect images and real-time video to remote operations centers for analysis. Technicians view video stream live while speaking with onsite individual as to level of threat parcel posses. Final evaluation process manipulates image to determine if item is considered Threat/No Threat. Technology also allows for Internet-based training by providing immediate access to experienced bomb technicians. Read More

Sensors, Monitors & Transducers

RFID-Based Electronic Safety Sensor has compact form factor.

October 8, 2014

Intended for application in safety circuits of hinged, sliding, or removable safety guards, RSS260 features LED status indicator, integrated dual monitoring microprocessor, optional serial diagnostics, and optional individual coding of actuators. Availability of standard actuator (RST-260-1); flat, elongated actuator (RST-16-1); and compact, rectangular target (RST-U-1) affords mounting flexibility. Sensor will accept any of these target actuators from 2 approach directions. Read More

Safety & Security Equipment, Sensors, Monitors & Transducers

Fall Management System features restraint-free design.

October 2, 2014

Designed to monitor patients or residents at risk of falling, Sensatec® Fall Management Solution brings added safety to senior living communities, hospitals, and rehabilitation facilities. Products include foldable bed and chair sensor pads, toilet sensor pad, and seat belt sensor, which connect to Sensatec alarm units to alert staff if at-risk patient or resident tries to get up without assistance. Made with non-slip, latex-free material, pads include protective connector plug. Read More

Plant Furnishings & Accessories, Sensors, Monitors & Transducers, Fasteners & Hardware

Safety System Escape Release permits unlocking from inside.

July 17, 2014

Designed for protecting and monitoring safety guards such as doors and flaps on machines and installations, Safety System ESL consists of handle and interlocking module equipped with transponder-coded safety technology CES. Escape release permits quick and straightforward unlocking of safety guard from inside, even if handle is locked. Release engages when actuated and prevents renewed closing of door. To close door and switch safety outputs on again, detent knob must be actuated. Read More

Electrical Equipment & Systems, Sensors, Monitors & Transducers

RFID Safety Switches maintain PLe and SIL3 levels.

July 16, 2014

Suitable for machines where hazardous conditions remain even after machines have been switched off, NG Series creates circuits with max safety level PLe and SIL3. Units can be connected in series up to max number of 32 devices, while maintaining safety levels. With electronic system for detection of actuator based on RFID technology, switches prevent tampering using another actuator of same series. Interlocking system guarantees actuator maximum holding force equal to 7,500 N. Read More

Safety & Security Equipment, Controls & Controllers, Sensors, Monitors & Transducers, Optics & Photonics

Integration Kit simplifies connection to access control systems.

July 2, 2014

With plug-and-play installation, EA-A01 Security System Integration Kit simplifies cabling and connections necessary between H3-EM Electronic Swinghandle with integrated card reader and any Wiegand-based access control system. Solution integrates with existing building access control infrastructure and extends data center security down to rack level. When integrated with existing access control system, kit facilitates complete remote control and monitoring. Read More

Safety & Security Equipment, Sensors, Monitors & Transducers, Green & Clean, Display & Presentation Equipment

Hybrid Lighting and Security System uses alternative energy.

June 17, 2014

With design powered by carbon fiber plastic wind turbine, solar panel, or stored power, Guard-Lite can be installed at any location without wiring or electrical permit. HD Wi-Fi Security Camera offers 2-way streaming audio and HD video, IR night vision, motion sensing, and alert notifications, while 3 LED lights with 6000K lamps deliver 900 lm each and last 60,000+ hr. With vinyl sleeve or powder coating, carbon steel mounting pole measures 4 x 4 in. and 14 ft 4" in. tall. Read More

Material Handling & Storage, Fluid & Gas Flow Equipment, Sensors, Monitors & Transducers

Safety Relief Valves offer pressure ratings to 750 psi.

June 12, 2014

Available in sizes from ½ x ¾ in. to 2 x 3 in. with 17 choices of inlet/outlet combinations, Series 740 offers soft or metal-to-metal seating choices, with closed cap, open, or packed lift levers. Full nozzle valves couple pivoted and bearing based post design with swivel styled seating. Constructed of stainless steel, bronze, carbon steel, or Monel, valves are designed for all ASME Section VIII services (air/gas/steam and liquid).  Read More

Electrical Equipment & Systems, Sensors, Monitors & Transducers

Non-Contact RFID Locking Switches offer 1,500 N max holding force.

May 29, 2014

Supplied in die-cast metal housing, MGL-M combines magnetic sensing and RFID technology to provide non-contact operation and anti-tamper coding. Electromagnet is used to lock machine guards. Coding is achieved by using RFID and magnetic techniques; both principles have to be satisfied for switch to operate safely. Respectively, holding forces range up to 1,500 and 1,000 N for MGL-1M and MGL-2M. There are 2 LEDs that offer 5 diagnostic functions to user. Read More

Electrical Equipment & Systems, Sensors, Monitors & Transducers

RFID Locking Switches offer holding force up to 1,200 N.

May 22, 2014

Manufactured in 316 stainless steel with mirror polished finish, Models MGL-SS and MGL-2SS offer holding force of 1,200 N and 600 N, respectively. Non-contact RFID switches with solenoid locking also feature electromagnet to lock guards, anti-tamper coding, and IP69K rating for CIP and SIP processes. Units come complete with 2 LEDs that offer 5 diagnostic functions. Operating with most safety relays, switches provide and maintain functional safety up to PLe/Cat 4 ISO13849-1. Read More

Electrical Equipment & Systems, Sensors, Monitors & Transducers

Grid Monitoring Relay ensures safe connection for wind turbines.

May 19, 2014

Ensuring safe, reliable, and proper grid connection at all times, CM-UFD.M33 (Grid Tie Relay) protects wind turbines from unstable grid activity or faults by disconnecting electric energy source from grid. Relay monitors voltage and frequency in single- and 3-phase grids and trips coupling switch when electrical values are not within set parameters. Upon fault detection, grid feeding monitoring relay sounds alarm, displays message, and signals alarm cause to control system. Read More

Controls & Controllers, Electrical Equipment & Systems, Sensors, Monitors & Transducers

Low-Water Cutoff Devices protect boilers and steam generators.

May 5, 2014

Offered in configurations and functions to suit various water feed vessels, LWC-700/720/800 Series features redundant switches within liquid level sensors as well as electronic controllers to deactivate systems before water supply problem can damage or create critical situation. Controller box may be mounted directly on sensor unit head or up to 2 ft away via optional electrical conduit configuration. Other options include manual reset, power outage resets, and operation testing. Read More

Electrical Equipment & Systems, Sensors, Monitors & Transducers

Heavy-Duty Safety Switches have touch-safe, visible blades.

April 25, 2014

Intended for commercial and industrial applications, 600 V and 200 kA rated switches feature globally rated bodies and meet UL98, CSA, and NEMA KS-1 standards for service-entrance and motor-load applications. Fully enclosed operating mechanisms are protected from dirt and debris. Ranging from 30–1,200 A, maintenance-free switches are available as fused and non-fused. Interior space in Type 1/12/3R/4X steel or stainless steel enclosures facilitates safe wiring/installation of accessories.
Read More

Safety & Security Equipment, Test & Measuring Instruments, Sensors, Monitors & Transducers

Electrical Safety Analyzer targets on-the-go technicians.

April 15, 2014

Built with rubberized case for durability, Model ESA609 integrates all functions needed to test medical devices when patient lead testing is not required, including: line (mains) voltage, ground wire resistance, equipment current, leakage current, and point-to-point tests. Portable unit tests to ANSI/AAMI ES1, NFPA-99, and parts of IEC62353 and IEC60601-1. With heavy-duty switches, users can
change polarity and configuration of neutral connection between open and closed. Read More

Test & Measuring Instruments, Sensors, Monitors & Transducers

Electrical Safety Test Systems suit production, laboratory use.

March 26, 2014

Electrical safety compliance test systems perform 4 common safety tests — AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond — with one DUT connection. Products include 2900 Series Hipot tester and 2600 Series Ground Bond tester, which can be interconnected to form complete test system that lets manufacturers perform electrical safety tests with single point of control. Milliohm Offset, Ramp Up, and Dwell features; 10 test memory locations; and PLC I/O are standard. Read More