Baumer Ltd.    Southington, CT 06489 1534
May 02, 2006 Projecting continuous 24 mm wide parallel beam to reflector, ParCon ZADM 034I analog optical line sensor permits edge and width detection to 1.0 mm. With measuring frequency greater than 1 kHz, unit measures metallic and non-metallic objects to resolution of 0.1 mm. User can program minimum object size using push button teach-in process. Housed in 67 x 34 x 16.6 mm package, sensor can control and sort by width/height, control and position sheet materials, and monitor parts for wear.

LEM Holding SA    Plan-les-Ouates CH-1228  Switzerland
May 02, 2006 Designed to measure voltage and impedance per cell as well as internal temperature of individual cells, Sentinel features intelligent SoC device that processes signal and interfaces to digital S-Bus control bus. Monitoring voltage, current, and impedance allows users to predict which cells are likely to fail, and to replace them, while temperature measurements ensure that thermal runaway situations are detected and corrected before they cause catastrophic failures.

Novotechnik U.S., Inc.    Southborough, MA 01772
May 02, 2006 Based on vertical Hall technology, Series RSC 1300 features cross structure that is affixed to silicon chip to provide 360° measurements with 10-bit resolution. Miniature non-contact sensors support maximum rotating speed of 10,000 rpm with sample rate of 10,000 kHz. Measuring 0.51 diameter x 0.8 in. long, units are housed in stainless steel and sealed to IP65. Applications include robotics, medical devices, and scientific instrumentation.

Henkel Corp.    Madison Heights, MI 48071
May 02, 2006 Using membrane sensors, Loctite® Fluid Waveform Analyzer C (LFWA-C) Series offers standardized application process for monitoring sealant and adhesive dispenses for variability. Rotospray mode monitors up to 4 short simultaneous dispenses, while single bead dispense analysis mode monitors single dispense operations. With modifiable parameters, processes can be refined to prevent production shutdowns by identifying potential problems before they arise.

MSA    Pittsburgh, PA 15230 0426
May 01, 2006 Designed to detect carbon monoxide, nitrogen dioxide, or refrigerants in air, Z Gard(TM) S uses solid state or electrochemical sensors, which generate representative output signal proportional to calibrated operating range. APOGEE Anywhere output allows sensors to communicate with other APOGEE Building Solutions over centralized network. Z Gard S is available in 4-20 mA analog output version as well as addressable RS-485 digital output model.

Fluid Imaging Technologies    Yarmouth, ME 04096
Apr 28, 2006 PetroCAM© oil analysis instrumentation integrates imaging, measuring, and reporting of droplet and particle concentration into single system. Hi-res digital images of suspended oil droplets, grains of sand, or other fluid-borne particles are displayed in interactive scattergram for instant review, differentiation, and analysis. Flow cell accommodates pressures up to 2,500 psi to permit operation at wellhead without altering pressurized state of sample.

Ortega Infosystems    Fremont, CA 94539
Apr 28, 2006 Combining mapping and video management software with MPEG-4 IP video components, VideoSm@rt(TM) is suited for mission-critical security applications. It includes all necessary components to set up, access, and manage IP video anywhere from one Web browser. Fully configured system provides map-based GUI for control over video information in systems comprised of tens to thousands of geographically dispersed cameras. NVR component enables video data to be captured and recorded.

MTS Systems Corp. - Sensor Div.    Cary, NC 27513
Apr 27, 2006 Tempsonics® Magnetostrictive R-Series includes options for 7,500 kHz update rates and position accuracy as low as ±20 microns. Internal measurement error-checking routine ensures immunity to shock and vibration. Featuring double-shielded design, field adjustable sensors come standard with IP67 housing and visual diagnostic LEDs. CANbus and Profibus DP industrial network sensors can sense up to 15 magnet positions and 5 magnet velocities simultaneously along single axis.

Linear Technology Corp.    Milpitas, CA 95035
Apr 27, 2006 Covering RF applications ranging from 300 MHz to 11 GHz, dual channel LTC5533 RF power detector supports multiple frequencies in single package. It features 40 dB dynamic range and 45 dB channel-to-channel isolation. Drawing 500 µA per detector, device is suited for dual-band Wi-Fi PA power control, dual-band cellular/WiMAX basestations, point-to-point microwave links, transmit PA forward and reverse power measurements, and low cost AM detector/receivers.

Matrikon Consulting Inc.    Edmonton, AB T5N4A3
Apr 27, 2006 ProcessGuard v4.0(TM) features interactive web reports, multi-language support, automated assessment that benchmark plant performance against ISA and EEMUA standards, as well as customized profiles so that each user can customize reports layout. Supervisors can gauge whether alarm loading problems exist, and technical staff can identify and eliminate nuisance alarms. Program helps operators respond to process situations before they become critical problems.

EMX Industries, Inc.    Cleveland, OH 44128
Apr 26, 2006 Powered by 9 V alkaline battery with 150-day life, P-44 Thru-Beam Sensor/Transmitter uses SP-44 solar panel to extend battery life by up to 2 years. Two-conductor, 20 ft cable connects panel to P-44 power input terminals. With proper power applied, detection distance between emitter and receiver can be up to 50 ft. When photoelectric beam is blocked, receiver activates relay that can be used for garage door reversal, electrical mechanism shutdown, and other safety functions.

BRUKER AXS Inc    Madison, WI 53711-5373
Apr 26, 2006 Powered by ESPRIT(TM) software, QUANTAX(TM) QUAD is designed for X-ray microanalysis on electron microscopes. It features 4-channel XFlash® QUAD Detector, which consists of 4 independently operating, 10 mm² Silicon Drift Detectors with integrated anodes and FETs. Cooled by Peltier elements, XFlash requires no liquid nitrogen and is maintenance-free. It accepts max input count rates in excess of 2,000,000 cps with standard energy resolution better than 133 eV at 10,000 cps.

Minco    Minneapolis, MN 55432
Apr 25, 2006 Comprised of IC with stable polymer element and platinum RTD used for temperature compensation, sensor is resistant to airborne contaminant and chemicals. Sintered stainless steel filter protects sensor and resists effects of condensation. Offered in wall/duct/OSA mounting configurations, product is specified over -10 to +150°F and -10 to +185°F non-condensing temperature ranges. It delivers 2-point field calibration and NIST traceable calibrations.

Banner Engineering Corp.    Minneapolis, MN 55441
Apr 25, 2006 SLM Series sensors, available in 6 fixed slot widths from 10-220 mm, provide opposed-mode sensing of objects as small as 0.30 mm that pass between emitter and receiver. Along with U-shaped metal housing, they include single-turn potentiometer sensitivity adjustment and visible red beam. Sensors, installed using molded-in beam guides, operate on 10-30 Vdc and are offered with current sourcing (PNP), current sinking (NPN), or bipolar (one NPN and one PNP) output.

Bunting Magnetics Company    Newton, KS 67114
Apr 24, 2006 As electronic, triple-coil metal detectors, Machine-Mounted Separator (MMS) systems sense and remove ferrous and non-ferrous metals from moving virgin and regrind material. Units reject contaminants as small as 0.5 mm and may be installed directly at infeed of extrusion, injection, and blow molding machines. Able to work with gravity and pneumatic systems, cube-shaped MMS units employ pneumatically driven slide gate combined with venturi-driven vacuum rejection mechanism.

Macro Sensors    Pennsauken, NJ 08110 1334
Apr 24, 2006 Available in ranges of 0.100-4.00 in., all-stainless steel GHSE 750 series operates from 15-24 Vdc inputs and generate pre-calibrated 0-10 Vdc output. Sensors consist of spring-loaded shaft running in precision sleeve bearing, which is connected to core of LVDT. Exhibiting max linearity error of ±0.25% of FS output, hermetically sealed, 19 mm dia sensors suit dimensional gauging applications and simplify mechanical set-up in automation applications.

Dytran Instruments, Inc.    Chatsworth, CA 91311
Apr 21, 2006 Operating over temperature range of -60 to 325°F, Model 3023AH has frequency range of 2-10,000 Hz with sensitivity of 10 mV/g. Welded hermetic sensor features .36 x .36 in. footprint. High-temperature rating makes accelerometer suited for automotive NVH applications on engines and HASS/HAST chambers when higher than usual temperatures are encountered. Unit is also valuable in critical flight test applications.

Associated Research, Inc.    Lake Forest, IL 60045
Apr 20, 2006 Designed to work with line leakage and functional run testing capabilities of OMNIA series of electrical safety compliance analyzers, AC1000 power source is used in applications requiring isolation transformer adjustable to 110% of line voltages. It features 1 kVA, programmable software current limits, programmable over-current fold back to maintain constant output current with varying load, 3-way power on condition, and 3 programmable memory locations.

BRUKER AXS Inc    Madison, WI 53711-5373
Apr 20, 2006 Suited for applications in petrochemistry, cement, and mining industries, S8 TIGER wavelength dispersive X-ray fluorescence (WDXRF) spectrometer analyzes all elements from Beryllium to Uranium in variety of sample types. SampleCare(TM) feature automatically recognizes liquid samples and has integrated protection seal to protect spectrometer against contamination. Integrated touch screen and dedicated user interface facilitate operation.

CLARE INSTRUMENTS US INC    Tampa, FL 33634
Apr 19, 2006 SafeCheck 8 electrical safety tester allows operators to program tests for ground bond, insulation, flash, short test, leakage, and run tests, or select from pre-programmed tests for Class I/II electrical equipment, extension cords, and locking power cord tools. Equipment/tools are automatically sequenced through test routine, where results are recorded. Capable of holding 5,000 test results, unit can also be used with barcode reader to scan ID number or pre-programmed test routines.