Dwyer Instruments, Inc.    Michigan City, IN 46361
Dec 07, 2011 Providing both low and high limit control, Series AT23000MR and AT23000MRS Photohelic® Switches/Gauges combine differential pressure switch with analog pressure gage. AT23000MR Series employs electromechanical relays, while AT23000MRS Series uses SPST (NO) solid state relays. Compatible with air and other non-combustible, non-corrosive gases, gauges handle pressures to 25 psig. Flame-proof ATEX enclosures have glass window for viewing set point needles and process pressure.

Amerlux, Inc.    Fairfield, NJ 07004
Dec 06, 2011 Along with LED module and built-in speaker, SmartSite(TM) Street Lights feature duo-band radio system and miniature computer with data storage capacity. Street light processors communicate with each other through bi-directional wireless mesh network and monitor individual luminaire usage, energy costs, grid power, and system integrity. Luminaires also offer multimedia solutions that can upgrade existing infrastructure to provide information, advertising, security and entertainment for public spaces.

Sensortechnics Inc.    Dublin, CA 94568
Dec 06, 2011 Featuring MEMS construction which integrates micro-flow channel and analog CMOS signal conditioning within silicon sensor chip, LBA Series is suited for differential pressure flow measurement where pressure drop across flow element is measure of volumetric flow rate. Sensors offer 0.01% resolution with dynamic range greater than 10,000. Immune to dust and condensation, sensors can be used with long connecting tubes and input filters without recalibrating or correcting output signal.

SAW instruments GmbH    Bonn D-53177  Germany
Dec 05, 2011 Optimizing mammalian cell-based binding assay workflow, sam®X provides 8 channels, each addressable by fluidics individually or in combinations, facilitating on-chip immobilization at each sensor position. System can be used with unfixed cells in suspension, which are injected afresh for each measurement, or adherent cells grown directly on sensor chips themselves. Completing assays in minutes, sam®X enables accurate real-time kinetics data to be captured.

Measurement Specialties, Inc.    Hampton, VA 23666
Dec 05, 2011 Based on COTS sensor with damped MEMS sensing technology, Model 4332 is available in ranges from ±2 to ±5 with low-pass filter set at 50 Hz. Temperature compensated device operates from -40 to +85°C and complies with IP68 requirements for submersion in water to 10 m depth. Packaged in aluminum housing with integral cable assembly, accelerometer can be screw- or adhesive-mounted. Unit operates from 5-30 Vdc excitation and offers 0.5-4.5 V full scale output.

Plastic Technologies, Inc.    Holland, OH 43528
Dec 02, 2011 Using ultrasonic sensor, LeakMonitor® continuously monitors blow molding process at production speeds for air leaks from machine components and defective bottles. Automated calibration features include display of relative severity of air leaks and where they are located on blow wheel. By monitoring blowing process for leaks in base or sidewall for short shots and other sealing surface defects, solution helps ensure rPET usage does not result in defective bottles leaving operation.

Meggitt (Maryland), Inc.    Germantown, MD 20876
Dec 02, 2011 Capable of continuous submersion, 712F-M4 and 997-M4 have captive screw design with safety wire hole and may be used on smaller, lighter structures without concern of mass loading. Integral cable design uses glass to metal seal technique, ensuring true hermetic seal tested to 100 psi. While 712F-M4 houses 100 mV/g vibration sensor with ±10% sensitivity and operates from 3 Hz to 25 kHz, 997-M4 comes with 10 mV/g output with ±5% sensitivity and frequency range down to 0.5 Hz.

Kistler Instrument Corp.    Amherst, NY 14228 2119
Dec 02, 2011 Designed to be fully operational on sand, gravel, snow, ice, and other surface conditions, Kistler Corrsys-Datron Type CHFA sensors are designed to support ride height, distance, as well as other static and dynamic vehicle measurement requirements. Measured values are provided as analog signals (0-10 V), RS-232C outputs, or CANBus messages. Offered in 3 models with working distances from 100-900 mm, series features sensing elements housed in anodized, corrosion-resistant aluminum package.

Automation Systems Interconnect Inc.    Mechanicsburg, PA 17055
Dec 01, 2011 Available in diffuse proximity, fixed focus proximity, polarized retroreflex, retroreflex for transparents, and through beam versions, S8 Series delivers detection performance suited for food and beverage industry, electronic plants, packaging lines, test and assembling machines, and automotive applications. Laser models, offered in coaxial polarized retoreflex and background suppression versions, feature focused spot below 1 mm and switching frequencies reaching 10 kHz.

Sensonics    Berkhamsted Hertfor HP1 1EF  United Kingdom
Dec 01, 2011 Vibration (DN8031) and thrust position (DN8033) proximity probe systems suit Ex ia IIC T4 applications when used in conjunction with Sensonics ATEX-approved AECP proximity probes and AEXC extension cables. Able to integrate with local machine PLC or plant wide DCS, these 4-20 mA loop powered modules permit adjustment of gain and offset. All signal processing is carried out within unit, providing output current proportional to peak-to-peak shaft vibration or relative position to probe face.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Dec 01, 2011 Designed for critical low differential pressure applications, Series RSM can be configured to monitor positive or negative pressure in protected environments and hospital isolation rooms per CDC guidelines. System includes backlit LCD with GUI that enables access to pressure, security, calibration, and alarm setup. LEDs and local audible alarm alert personnel to system status. Made of NEMA 1 rated fire retardant plastic, monitor displays true differential pressure with 0.001 in. wc resolution.

Kistler Instrument Corp.    Amherst, NY 14228 2119
Dec 01, 2011 Supporting plastics injection molding requirements, Type 4021B is designed for simultaneous recording of short duration pressure peaks to 29,000 psi and temperatures to +662°F. Device is available with choice of voltage or current output and incorporates melt pressure sensor with abrasion-resistant stainless steel diaphragm and integral amplifier. Performance characteristics allow sensor mounting directly in material flow, eliminating time lag for real-time process parameter measurement.

Nonin Medical, Inc.    Plymouth, MN 55447
Nov 29, 2011 EQUANOX(TM) Model 7610 serves medical monitoring manufacturers who desire solution for integrating cerebral and tissue oximetry technology into their patient monitoring systems. Regional oximetry noninvasively measures oxygen saturation, allowing clinicians to improve outcomes by peri-operative monitoring on targeted tissue beds. To accommodate different clinical requirements, system comes in 2- and 4-channel configurations and provides Type-A USB connector.

Brüel & Kjær    Norcross, GA 30071-1588
Nov 28, 2011 Offered as subscription-based service, Construction Sentinel facilitates effective compliance monitoring at construction sites by combining noise and ground vibration monitoring. Solution also enables users to identify cause of vibration events by remotely listening to noise on site. Managed from same platform, service alerts users in real-time and automatically compiles and distributes reports that show compliance with legislation.

TAOS Inc.    Plano, TX 75074
Nov 28, 2011 Suited for OLED-based smartphones, Series TCS3x71 and TCS3x72 provide color measurement, and when coupled with IR LED, proximity detection within wide range of lighting conditions and through variety of attenuating materials. TCS3x72 Series includes IR blocking filter integrated directly on-chip and localized only to color sensor photodiodes, eliminating need for external IR filtering. On-chip IR blocking filter enables devices to also perform ambient light sensing.

Dynapar    Gurnee, IL 60031
Nov 28, 2011 Featuring stainless steel sensor modules and ductile iron housings, RIM Tach 6200 and RIM Tach 1250 provide position and velocity feedback from electric motors in heavy-duty environments. Sensor modules use magnetic technology that delivers 70 thousandths air gap. To facilitate installation, devices are designed with axial play up to 0.50 in. and do not require precision tools or measurements. Diagnostic LED provides visual status of encoder functionality.

Novotechnik U.S., Inc.    Southborough, MA 01772
Nov 25, 2011 Measuring 3.54 in. diam x 0.59 in. height, Vert-X 90E Series features 0-360°measurement range and 0.1° repeatability. Magnetic pick up is secured to rotating object so there is no direct mechanical linkage between shaft and measuring system and no wear. Available with IP68 or IP69 protection rating, sensors offer up to 2 switch outputs, independent linearity to 0.3%, and 14-bit resolution. Output options include voltage of 10-90% of power supply, SPI, and PWM.

Kistler Instrument Corp.    Amherst, NY 14228 2119
Nov 23, 2011 Accepting inputs from up to 4 piezoelectric cavity pressure sensors, Type 2869B0 Entry Level CoMo Injection provides real-time visual display of cavity pressure curves during actual injection molding process. Modular data acquisition system allows for addition of monitoring capabilities based on actual molder job fulfillment requirements. User-selectable capabilities include digital output, real-time threshold capability, and ability to export information to data collection software.

Pepperl + Fuchs, Inc.    Twinsburg, OH 44087 2245
Nov 22, 2011 Able to detect clear materials, very small objects over large area, and glossy materials without need for reflector, Series ML100-8-W is suited for material handling and packaging as well as assembly, automotive, and printing applications. Units feature multi-color LEDs that are visible from 360° for immediate sensor status detection. Resistant to ambient light, sensors include cross-talk protection and operate over extended temperatures of -22 to +140°F.

Kistler Instrument Corp.    Amherst, NY 14228 2119
Nov 22, 2011 Operating to 50 psi and with nominal sensitivity of 100 mV/psi, model Type 211B6 comes in stainless steel housing and incorporates on-board acceleration-compensation, high natural frequency, and low-impedance Piezotron® circuit electronics. Pair of preloaded quartz assemblies, located behind diaphragm, are comprised of quartz plates interleaved with gold electrodes. Other features include microelectronic signal conditioning circuit and acceleration compensation.