E+E Elektronik GmbH    Engerwitzdorf A-4209  Austria
Aug 20, 2010 With measuring range of up to 10,000 ppm, EE892 employs CO2 load cell based on infrared technology (NDIR). Features, such as adjustable measuring interval, enable sensor to be adapted to specific applications. Average current consumption is less than 60 µA, and auto-calibration process minimizes maintenance. Digital interface and compact design facilitate integration in mobile and energy-sensitive applications.

Silicon Designs, Inc.    Issaquah, WA 98027
Aug 20, 2010 Integrating 3 orthogonally mounted accelerometers in epoxy sealed anodized aluminum case, SDI 2460 series provides high-precision shock, vibration, and acceleration measurement in 3 orthogonal directions. On-board voltage regulation and internal voltage reference makes units relatively insensitive to temperature and voltage changes and eliminate need for external power amplification and regulation. Models can be mounted to test article or fixture via glue, epoxy, or 2 #8 or M4 screws.

Safety Technology International    Waterford, MI 48327
Aug 19, 2010 Unaffected by people, animals, and shadows, solar-powered (STI-34100) and battery-powered (STI-34150) models detect when vehicle enters/exits home or office driveway. Magnetometer sensor system detects movement of any large metallic (iron or steel) object and sends signal using 433 MHZ wireless frequency from transmitter to indoor receiver, which will chime and flash. Solution may be placed as far as 1,000 ft (line of sight) away from receiver indoors.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Aug 19, 2010 Series DTM provides uninterrupted liquid level indication for 30 or 55 gal storage tanks or vessels. Stem and mounting fixtures are available in 316 SS or brass, and only float and stem make contact with liquid to ensure indication tape is always clean and readable. Accurate to 1/16 in. and available in lengths from 6 in. to 6 ft, manual indicator is customizable to meet specific application requirements.

Sensor Synergy    Buffalo Grove, IL 60089
Aug 18, 2010 Watts Aware WA-118 measures and reports real-time power consumption information for motor-driven machines, HVAC, lighting, or groups of electricity-consuming equipment. System includes three 200 A current sensors and three 500 A current sensors, pre-configured netbook computer, Watts Aware DAQ Unit, wireless router, and all software and cables required to make system operational out-of-the-box. System can be installed without interrupting operational status of equipment to be monitored.

Tektroniks    Nottingham   United Kingdom
Aug 17, 2010 Wireless Gas Leak Detection Sensors enable full range of gases to be monitored, with refrigerant, ammonia, toxic, and combustible versions available immediately. Designed to compliment Wireless DATAcentre Monitoring System as well as SAMie Control and Monitoring System, sensors produce system alarm through base station as well as at actual sensor point. This minimizes risk of employee/customer entering area where gas leak is detected.

CAS Data Loggers    Chesterland, OH 44026
Aug 16, 2010 Powered by external 12 V supply with internal NiMH back-up battery that can provide up to 100 hours of operation, Eltek GD47 collects temperature, humidity, and CO2 measurements and sends them wirelessly to receiver for storage, display, and alarming. Equipped with NDIR sensor, unit measures CO2 from 0-5,000 ppm, temperature from -20 to +65°C, and humidity from 0-100% RH. Wireless range can be several hundred feet to almost 1 mile, depending on transmitter frequency and environment.

E+E Elektronik GmbH    Engerwitzdorf A-4209  Austria
Aug 16, 2010 Suitable for demanding operating conditions and outdoor applications, IP65-rated EE240 Series enables up to 3 intelligent probes to be connected to each transmitter. Each probe operates independently, can be hot swapped, and allows sensing head to be placed up to 10 m away from transmitter. Measured values can be read directly off display on transmitter or remotely via web browser from any PC in network. Base station includes 4 analog outputs for connection to system controller.

Lincoln Industrial    St. Louis, MO 63120 1578
Aug 16, 2010 Combining Mityvac Selectline hand pressure pump with 4 cooling system test adapters and 2 dual-function cap test adapters, Model MV4560 finds leaks and defective caps in cooling systems of cars and light trucks. Unit can pinpoint external cooling system leaks caused by loose clamps or leaky hoses, connectors, water pumps, or radiators. Kit can also diagnose internal leaks caused by blown head gaskets or damaged blocks or heads.

Renishaw, Inc.    Hoffman Estates, IL 60192
Aug 13, 2010 Providing true absolute positioning in linear/rotary models, RESOLUTE(TM) has single-track optical scale that eliminates misalignment and allows wide setup tolerances. Resolution of 1 nm at up to 100 m/s accommodates linear and angle encoding applications, and absolute position is acquired immediately upon switch-on and without battery backup. Product reads fine-pitch, 30 µm scale, resulting in noise levels with jitter less than 10 nm RMS. Sub-divisional error is ±40 nm.

Newport Electronics, Inc.    Santa Ana, CA 92704
Aug 13, 2010 With Model iSD-TC, users can monitor and record temperature of critical equipment and locations over Ethernet network or Internet via Web browser. Device can trigger alarm if temperature goes above or below user-determined set point, and alarms can be sent by email to single user or to group distribution list, including text messages to cell phones and PDAs. Supplied with removable 2 GB Flash Memory card, monitor enables user to store up to 7 years of readings taken at 10-sec intervals.

AMETEK Solartron Metrology    Gastonia, NC 28054
Aug 13, 2010 Designed to test electrical properties of materials ranging from insulators to superconductors, ModuLab MTS combines time domain tests and AC tests together with wide range of modules, providing high voltage, high current, resolution, and sample/reference measurements. Core of system is MAT core module, which makes use of DSP technology to provide accurate experiment control, data acquisition, data averaging, and responsive safety and step limit detection.

Maxim Integrated Products    Sunnyvale, CA 94086
Aug 13, 2010 Providing 12-cell measurement, Model MAX11068 employs capacitor-isolated SMBus-laddered communication bus, which allows up to 31 devices to be connected in series to monitor up to 372 cells. Analog front-end combines 12-channel voltage-measurement data-acquisition system with fault-tolerant switch bank input. Using 12-bit ADC to digitize cell voltages, MAX11068 delivers less than ±0.25% error over normal battery temperature ranges and ±20 mV error over full AEC-Q100 Type 2 temperature range.

Baumer Ltd.    Southington, CT 06489 1534
Aug 13, 2010 Insensitive to changing color or reflectivity of printed materials, SCATEC Clamp Sensor counts newspapers transported via conveyor clamps or grippers. Laser optics and internal algorithm are used to count number of documents in clamp as well as detect presence and number of copies in one gripper. Documents as thick as 0.25 mm can be measured at sensing ranges to 120 mm, and accurate detection can take place at travel speeds to 5 m/sec. Visible red laser beam facilitates alignment.

Vacuum Instrument Corp.    Ronkonkoma, NY 11779
Aug 13, 2010 Suited for testing integrity of vacuum systems and parts, MS-60 Series comes with touchscreen GUI that promotes control and monitoring during system start-up and operation. GUI displays system status and accept/reject status, as well as system health, setup, calibration, and other diagnostic functions. Chart Mode lets operator simultaneously view strip chart of leak rate, range, and set point, while System Diagnostic Mode lets operator monitor several operating parameters.

GAO RFID Inc.    Toronto   Canada
Aug 12, 2010 Measuring 80 x 57 x 19 mm, portable model 223015 addresses HF (13.56 MHz) and LF (125 kHz) RFID tags simultaneously. Hot-pluggable unit, able to read/write tags at distances to 70 mm, has USB interface for data transmission and power. Areas of use include RFID tag/label verification and programming, personnel identification and access control to computers terminals or POS applications, as well as other applications for supply chain, retail, or logistics.

KLA-Tencor Corp.    San Jose, CA 95134
Aug 12, 2010 Utilizing Patented Broadband Spectroscopic Ellipsometry, white light reflectometry, and optional UV reflectometry optics technologies, Aleris(TM) 8330 measures film thickness, refractive index, and stress of non-critical films at 32 nm node and beyond. Unit offers remote recipe management and enables recipe import from previous generation platforms. Recipe sharing among Aleris tools facilitates flexible process control strategy within fab, covering high- and low-end film applications.

Meggitt Sensing Systems (Endevco Corp.)    San Juan Capistrano, CA 92675
Aug 11, 2010 Endevco® model EM46BD combines ¼ in. ISOTRON® pressure microphone and TEDS-enabled preamplifier in preassembled kit that is constructed of stainless steel. Designed to IEC 61094 Class 1 standard, microphone has 10 Hz to 70 kHz audio frequency range and wide dynamic range. Device uses TEDS technology that allows for microphone and preamplifier to be recognized by smart-transducer compatible input module. Unit is suited for aerospace, automotive, and general laboratory testing applications.

ControlAir Inc.    Amherst, NH 03031 2315
Aug 11, 2010 Able to mount directly to common valve actuators, I/PAC (Integrated Process Air Control) assembly is offered with choice of explosion-proof, field-mounted I/P transducer that comes pre-assembled with filter regulator and pressure gauge. Tapped exhaust option enables use in natural gas applications, and field selectable outputs are 3-15, 3-25, 6-30, and 1-17 psig. Able to withstand harsh environments, product carries all agency hazardous area approvals from FM, CSA, and ATEX.

Elobau Sensor Technology, Inc.    Lake Bluff, IL 60044
Aug 10, 2010 Featuring integrated CANopen protocol according to ISO 11898, 424CO rotary position sensor is based on Hall effect magnetic sensing technology. Contactless sensing element promotes reliability. Measuring range is 360°, with 0.1° resolution over entire range, and shaft is supported by ball bearings in order to allow radial forces. Protected to IP67, sensor operates over -40 to +85°C range and withstands EMC up to 200 V/m. Sensor operates 9-32 Vdc supply.